User Manual User guide

replace the SPED module.
601 ERR SPED REPORTED INVALID
ENCRYPT MODE
Inspect cable from main board assembly to the SPED module for
damage. Mak
e sure
that the cable is connected at both ends.
Verify that the DC operating voltages are correct. Restart ATM.
Clear the error. If error persists, replace the SPED module.
602 ERR SPED REPORTED
UNSUPPORTED CLEAR OPTION
Inspect cable from main board assembly to the SPED module for
damage. Mak
e sure
that the cable is connected at both ends.
Verify that the DC operating voltages are correct. Restart ATM.
Clear the error. If error persists, replace the SPED module.
603 ERR SPED REPORTED TAMPER
PRESENT
Inspect cable from main board assembly to the SPED module for
damage. Mak
e sure
that the cable is connected at both ends.
Verify that the DC operating voltages are correct. Restart ATM.
Clear the error. If error persists, replace the SPED module.
604 ERR SPED REPORTED INVALID KEY
INDEX
Inspect cable from main board assembly to the SPED module for
damage. Mak
e sure
that the cable is connected at both ends.
Verify that the DC operating voltages are correct. Restart ATM.
Clear the error. If error persists, replace the SPED module.
605 ERR SPED REPORTED PARENT KEY
NOT LOADED
Inspect cable from main board assembly to the SPED module for
damage. Mak
e sure
that the cable is connected at both ends.
Verify that the DC operating voltages are correct. Restart ATM.
Clear the error. If error persists, replace the SPED module.
606 ERR SPED REPORTED WRONG
DATA LENGTH
Inspect cable from main board assembly to the SPED module for
damage. Mak
e sure
that the cable is connected at both ends.
Verify that the DC operating voltages are correct. Restart ATM.
Clear the error. If error persists, replace the SPED module.
607 ERR SPED REPORTED PIN RETRY
TOO SOON
Inspect cable from main board assembly to the SPED module for
damage. Mak
e sure
that the cable is connected at both ends.
Verify that the DC operating voltages are correct. Restart ATM.
Clear the error. If error persists, replace the SPED module.
608 ERR SPED SELFTEST CRC FAILED
Inspect cable from main board assembly to the SPED module for
damage. Make sure
that the cable is connected at both ends.
Verify that the DC operating voltages are correct. Restart ATM.
Clear the error. If error persists, replace the SPED module.
609 ERR SPED SELFTEST
CRYPTOGRAPHIC ERROR
Inspect cable from main board assembly to the SPED module for
damage. Mak
e sure
that the cable is connected at both ends.
Verify that the DC operating voltages are correct. Restart ATM.
Clear the error. If error persists, replace the SPED module.
610 ERR SPED SELFTEST BATTERY LOW
STATUS
Inspect cable from main board assembly to the SPED module for
damage. Mak
e sure
that the cable is connected at both ends.
Verify that the DC operating voltages are correct. Restart ATM.
Clear the error. If error persists, replace the SPED module.
611 ERR SPED SELFTEST SERIAL
NUMBER ERROR
Inspect cable from main board assembly to the SPED module for
damage. Mak
e sure
that the cable is connected at both ends.
Verify that the DC operating voltages are correct. Restart ATM.
Clear the error. If error persists, replace the SPED module.
612 ERR SPED TAMPER STATUS COLD
Verify all SPED connections. Restart the operating system. Clear
any errors conditi
ons. Inspect the battery for a voltage reading of
greater than 2.8 VDC. Replace SPED battery is below 2.8 VDC.
Replace SPED module if error persists.
613 ERR SPED TAMPER STATUS FRONT
Inspect cable from main board assembly to the SPED module for
damage. Make sure
that the cable is connected at both ends.
Verify that the DC operating voltages are correct. Restart ATM.
Clear the error. If error persists, replace the SPED module.
614 ERR_SPED_TAMPER_STATUS_BACK
Inspect cable from main board assembly to the SPED module for
damage. Make sure
that the cable is connected at both ends.
Verify that the DC operating voltages are correct. Restart ATM.
Clear the error. If error persists, replace the SPED module.
37