Congratulations Dear Kirby Customer, Congratulations on the purchase of The Ultimate G series™. You now own a superior, complete home maintenance system designed to help make your home and furnishings look better and last longer. Most importantly, repeated use of your Kirby® Ultimate G will give you the type of clean in-home environment you want and deserve. This use and care manual is designed to help you get the most out of your new Kirby Ultimate G and enjoy its numerous benefits and features.
Important Safety Instructions The Ultimate G series™ Model G7D is Listed and Certified by Underwriters Laboratories Inc. and Canadian Standards Association as a double insulated appliance. The Model 293001 and 295001 Carpet Shampoo System, Model 293101 and 295101 Floor Care System, Model 293501 Zippbrush™ and Model 293201 Turbo Accessory System™ are also Listed and Certified as Optional Accessories for use with this Kirby® model.
Table of Contents Important Safety Instructions About this Manual Kirby® Micron Magic® HEPA Filtration Part 1 — Getting Started Moving Your Ultimate G/Handle Tilt Latch/Toe-Touch Control™ 7 Power Nozzle Height Adjustment/TechDrive® Power Assist 8 Installing/Changing Disposable Filter Bags 9 Bag Support Strap/Mini Em-Tor® 10 The Belt Lifter 10 Part 2 — Upright & Portable Cleaner The Upright Cleaner 13 The Upright as a Straight Suction Cleaner 14 The Portable Cleaner 15 Part 3—Canis
About This Manual Using this Owner's Manual This Owner’s Manual was designed to be easy to read and follow. It has been organized in sections based on the various ways you may use your new Kirby® Ultimate G. Within each section, simple step-by-step illustrations will help you easily visualize the steps required to properly operate your new Ultimate G and its many attachments and optional accessories.
You bought the best; you expect the best. That’s why Kirby developed the Micron Magic HEPA (High Efficiency Particle Arrest) Filtration System featuring the latest in clean air technology without sacrificing Kirby’s tremendous airflow. * * Captures and retains 99.97% of household dust, pollen, dust mites and other particles down to 0.3 microns. Captures and retains 99.5% of other particles down to 0.1 microns.
Getting Started PART ONE This section outlines general information you will need as you begin using your new Kirby® Ultimate G. It includes information on: Moving and Carrying Your Ultimate G Using the Handle Tilt Latch The Toe-Touch Control™ Proper Power Nozzle Height Using TechDrive® Power Assist Installing/Changing Disposable Filter Bags Emptying the Mini Em-Tor® Understanding the Belt Lifter Please read this section (as well as all other sections) carefully before using your new Ultimate G.
Getting Started Moving/Carrying Your Ultimate G/Handle Tilt Latch and Toe-Touch Control™ MOVING YOUR ULTIMATE G Your Ultimate G is equipped with TechDrive® Power Assist. In order to push your Ultimate G with the motor OFF, TechDrive Pedal o 11 must be turned OFF (disengaged). Turn TechDrive OFF by pushing down on the gray “N” side (marked “N” for Neutral) of the TechDrive Power Assist N/D Pedal. (See page 8 for additional information.
Getting Started Power Nozzle Height Adjustment and TechDrive® Power Assist Then, each time you press on the Toe-Touch Control™Upper Pedal o 8 , you will lower the front one notch. The number of bars showing above the Toe-Touch Control provide an indication of height. ❏ POWER NOZZLE HEIGHT ADJUSTMENT When using the Power Nozzle o 25 , it is important to adjust the height properly.
Getting Started Installing/Changing Disposable Filter Bags INSTALLING/CHANGING DISPOSABLE FILTER BAGS A Disposable Filter Bag must be installed before you begin vacuuming. 1 2 To install a new Disposable Filter Bag, unzip the Outer Permanent Bag o 1 and pull out the Disposable Filter Bag along with the Top Adaptor o 5 . ➤ When necessary, remove the used Disposable Filter Bag. NOTE: Always replace the Disposable Filter Bag when dirt reaches the “FULL” line on the bag.
Getting Started Bag Support Strap/Mini Em-Tor® and Belt Lifter BAG SUPPORT STRAP 4 Check to make sure the Bag Support Strap o 4 is connected to the Top Adaptor o 5 . The Bag Support Strap provides the support required for proper operation of the Disposable Filter Bag. If it is not connected, thread the strap through the small hole of the Top Adaptor. Then place the hole in the strap over the stud on the Top Adaptor.
Getting Started The Belt Lifter (continued) USING THE BELT LIFTER (cont) 1 To use the Belt Lifter, you must first raise the Headlight Hood o 21 . ➤ 2 Flip out the L-shaped handle on the Belt Lifter o 20 . Use it to turn the Belt Lifter fully to the left (counter-clockwise) until it stops and the red arrows line up. This stretches the belt and lifts it off the motor shaft. Return the L-shaped handle on the Belt Lifter to its closed position.
Upright & Portable Cleaner PART TWO Your Kirby® Ultimate G is an extremely versatile home maintenance system. In this section, we will discuss the following: Using your Ultimate G as an Upright Cleaner Using your Upright as a Straight Suction Cleaner Cleaning Hard-Surface Floors Using your Ultimate G as a Portable Cleaner Cleaning Mattresses and Carpeted Stairs This section provides the information you need to use your Ultimate G for a wide variety of jobs.
Upright & Portable Cleaner The Upright Cleaner THE UPRIGHT CLEANER Before you begin vacuuming, it’s important to have the Power Nozzle o 25 adjusted to the proper height setting. This gives you the most efficient cleaning action. Lowering the Power Nozzle too far prevents proper cleaning and shortens belt life.
Upright & Portable Cleaner The Upright Cleaner/Straight Suction Upright Cleaner 4 If power assist is desired, engage TechDrive® by pushing down the yellow “D” side (marked “D” for Drive) of the TechDrive Power Assist N/D Pedal o 12 located just below the Power Switch o 13 . ➤ 5 To turn your Ultimate G OFF, press the Toe-Touch Control™ Bottom Pedal o 9 all the way down until nozzle is fully raised.
Upright & Portable Cleaner The Hard Floor Pad and The Portable Cleaner THE HARD FLOOR PAD By attaching the optional Hard Floor Pad to your Ultimate G, you may dust bare floors. While the Ultimate G is turned OFF, raise the Power Nozzle o 25 as far as it will go by pressing the Toe-Touch Control™ Bottom Pedal o 9 . Attach the Hard Floor Pad onto the nozzle opening using the spring clips on the plate.
Upright & Portable Cleaner The Portable Cleaner PORTABLE CLEANER SET-UP (cont) 4 Bend the Filtration Bag Assembly o 1 in half and insert the Bag Latch Tab o 2 into the slot on the Portable Handle until it snaps into place. You are now ready for portable power cleaning. ❏ NOTE: Do not use portable mode on upholstered furniture. CARPETED STAIRS Place your Ultimate G on one of the carpeted steps, while supporting the rear of the Ultimate G.
Canister Cleaner & Attachments PART THREE Your Kirby® Ultimate G comes with a wide variety of attachments for added versatility.
Canister Cleaner & Attachments Converting to a Canister Cleaner/Installing the Attachment Hose CONVERTING TO A CANISTER CLEANER/ INSTALLING THE ATTACHMENT HOSE When using different cleaning attachments, the Attachment Hose is connected to the front of the cleaner in place of the Power Nozzle o 25 . NOTE: When connecting the Attachment Hose, you may choose between the Upright Handle o 17 or the Portable Handle o 15 . To install the Portable Handle, see page 15.
Canister Cleaner & Attachments Installing/Using the Attachments INSTALLING ATTACHMENTS ON THE ATTACHMENT HOSE To attach tools to the hose, push lightly while twisting the smaller end of the hose into the tool. ❏ ATTACHING THE SUCTION RELIEF UPHOLSTERY PANEL To attach the suction relief faceplate for drapes and delicate upholstery, insert the lip on the front edge of the upholstery tool under the two tabs on the front of the suction relief faceplate as shown.
Canister Cleaner & Attachments Using the Attachments DUSTER BRUSH The Duster Brush may be connected to the Attachment Hose or the Extension Tubes to remove dust from any surface, including contoured or irregular surfaces. ❏ UPHOLSTERY NOZZLE The Upholstery Nozzle is used for cleaning upholstered furniture, carpeted steps, clothing and inside of cars.
Canister Cleaner & Attachments Using the Attachments/Using Your Ultimate G as a Blower MASSAGE CUP Used with the Attachment Hose, the Massage Cup provides an invigorating skin or scalp massage. It can also be used to clean the floors of cars. ❏ CONTROLLING AIRFLOW WITH THE SUCTION CONTROL GRIP Sometimes when using the attachments, vacuuming drapes or delicate lamp shades, for example, you might wish to control the amount of suction.
Canister Cleaner & Attachments Using your Ultimate G as a Blower (continued) BLOWER SET-UP (cont) 2 Raise the Headlight Hood o 21 and flip out the L-shaped handle on the Belt Lifter o 20 . Use it to turn the Belt Lifter all the way to the left (counter-clockwise) until the red arrows line up. ➤ 3 Unlock the Power Nozzle o 25 by turning the Accessory Lock o 22 all the way to the left (counter-clockwise). The Power Nozzle should tip forward when it is released.
Canister Cleaner & Attachments Using your Ultimate G as a Blower (continued) BLOWER SET-UP (cont) 6 Place the large end of the Attachment Hose over the Air Exhaust Port o 19 . Line up the Indicator Arrow on the Hose End with the Indicator Arrow on the Air Exhaust Port and twist the Hose Connector to the right (clockwise) to lock it in place. If the Ultimate G will not operate, see page 51, question 2, items 4 and 5. ❏ USING YOUR ULTIMATE G AS A BLOWER Your Ultimate G may now be used as a blower.
Canister Cleaner & Attachments The Portable Sprayer (Blower Mode Only) THE PORTABLE SPRAYER The Portable Sprayer is used only in the Blower Mode. It is an excellent tool to apply many different types of water-based liquids to any type of surface. The spray can be adjusted ranging from very fine to coarse. PORTABLE SPRAYER SET-UP 1 Unscrew the jar from the Portable Sprayer and fill 3/4 full with non-flammable liquid.
Canister Cleaner & Attachments The Portable Sprayer USING THE PORTABLE SPRAYER (cont) 2 With the nozzle pointed away from you, adjust the spray by turning the Spray Adjustment Control on the trigger of the Portable Sprayer. ➤ 3 Use slow, sweeping motions to spray the desired area with solution. Always squeeze the trigger fully to permit maximum flow. This will give you the best spray control.
Canister Cleaner & Attachments The Portable Sprayer (continued)/The Portable Shampooer CLEANING THE PORTABLE SPRAYER (cont) 3 The spray opening on the front of the Sprayer also pulls out so that the inside of the Sprayer and the nozzle jet can be cleaned. To remove the nozzle jet, press on the two latches on the front of the nozzle jet and pull it out. (The latches must be aligned with the holes on the front of the Sprayer when returning the nozzle jet to the front of the Sprayer.
Canister Cleaner & Attachments The Portable Shampooer USING THE PORTABLE SHAMPOOER 1 Before shampooing, vacuum surface thoroughly. To make suds, turn the Ultimate G ON and pull the trigger of the Portable Sprayer. A stream of suds will come out of the cap. The suds can be sprayed directly onto the surface being cleaned or on a plain paper bag or in a bowl and then applied to the surface being cleaned.
28 T h e K i r b y C o m pa n y
Optional Accessories PART FOUR Optional Kirby® Accessories greatly enhance the usefulness of your new Ultimate G. In this section, we will discuss the following: Using the Carpet Shampoo System Using the Floor Care System Using the Turbo Accessory System™ Using the Zippbrush™ This section will provide the information you need to take advantage of your Kirby Optional Accessories.
Optional Accessories The Carpet Shampoo System CARPET SHAMPOO SYSTEM SET-UP Vacuum thoroughly before shampooing for maximum cleaning. Then, remove the Outer Permanent Bag o 1 and the Power Nozzle o 25 to prepare for shampooing. 1 By using the L-shaped handle, turn the Carpet Shampoo System Nozzle Belt Lifter to the right (clockwise) until the green arrows line up. ➤ 2 Slide the slots on the side of the Carpet Shampoo System Nozzle over the outer shoulders of the Carpet Shampoo System Tray.
Optional Accessories The Carpet Shampoo System CARPET SHAMPOO SYSTEM SET-UP (cont) 5 While sliding the Carpet Shampoo System Nozzle/ Tray Assembly toward the Ultimate G and over the Motor Shaft o 23 , connect the hooks on the bottom rear of the nozzle to the Attaching Bar o 24 . ➤ Push the nozzle up against the Ultimate G and turn the 6 22 to the right (clockwise) to lock the Accessory Lock o nozzle in place.
Optional Accessories The Carpet Shampoo System (continued) 8 Taking care to avoid spilling liquid on the Ultimate G or the floor, place the opening in the bottom front of the Shampoo Tank over the Air Exhaust Port1o 9 on the Ultimate G. Angle the Shampoo Tank outward from the Ultimate G until the arrows line up. Next, slide the Shampoo Tank down over the locking pins on the Air Exhaust Port. Rotate the Shampoo Tank toward the Ultimate G (clockwise) to lock it in place.
Optional Accessories The Carpet Shampoo System (continued) USING THE CARPET SHAMPOO SYSTEM (cont) As you move the Ultimate G back and forth, foam will be released and the brush will work it into the carpet. NOTE: Suds should be dispensed the full width of the tray when the Ultimate G is pulled backward. If not, pull back more slowly or check and clean the Shampoo Tank Filter, if necessary (see page 35).
Optional Accessories The Carpet Shampoo System (continued) CLEANING THE CARPET SHAMPOO SYSTEM (cont) 4 Turn the Accessory Lock o 22 to the left (counterclockwise). The Carpet Shampoo System Nozzle/Tray Assembly will tip forward. Lift the Nozzle/Tray Assembly off the Ultimate G and carry it to the sink. ➤ 5 6 Remove the hose from the tray and rinse. ➤ By using the L-shaped handle, turn the Belt Lifter to the right (clockwise) until the green arrows line up. Pull the tray and nozzle apart. Rinse tray.
Optional Accessories The Carpet Shampoo System (continued) CLEANING THE CARPET SHAMPOO SYSTEM (cont) 8 To remove the Shampoo Tank from the Air Exhaust Port1o 9 , rotate it away from the Ultimate G as far as it will go, then lift it upwards. ➤ 9 Remove and clean the Suds Screen Cap, Cup and Sponge Filter. Rinse out the Shampoo Tank with cold water and replace the Screen Cap, Cup and Sponge Filter. NOTE: The belt should not be stretched for extended periods.
Optional Accessories The Carpet Shampoo System (continued)/The Floor Care System-Miracle Waxer® REPLACING A WORN CARPET SHAMPOO SYSTEM NOZZLE BELT (cont) 3 Align the metal ends of the brush with the slots on the tray and push the brush in until it snaps into place. The brush will only fit the tray the correct way. NOTE: The belt should not be stretched when stored for an extended period. Make sure the green arrows line up for storage (see page 10 for discussion of the Belt Lifter).
Optional Accessories The Floor Care System-Miracle Waxer® (continued) USING THE KIRBY® MIRACLE WAXER (cont) 3 Pull the roller bag off the wax roller and save the packing bag. Begin waxing according to the directions in box on previous page. ➤ 4 To remove the wax roller from the long handle, hold the original wax roller packing bag with the open end facing the roller. Push the wax roller into the packing bag as far as it will go. Avoid touching the wax with your hand.
Optional Accessories The Floor Care System-Floor Buffer FLOOR BUFFER SET-UP Your Ultimate G can be used as an effective floor buffer for wood or tile floors. To use the Floor Buffer, you must first insert the Buffer Brush into the Floor Buffer Nozzle. NOTE: Use only approved Kirby® belts. 1 2 3 Center the belt of the Buffer Brush in the middle area between the tufts of the brush. ➤ Turn the Buffer Nozzle over and slide the ends of the Brush into the slots at each end of the nozzle.
Optional Accessories The Floor Care System-Floor Buffer (continued) FLOOR BUFFER SET-UP (cont) 5 Place the hooks located on the rear of the nozzle over the Attaching Bar o 24 and push the nozzle up against the Ultimate G. Turn the Accessory Lock o 22 all the way to the right (clockwise) to lock the nozzle in place. ➤ 6 To engage the drive belt and Buffer Brush, use the L-shaped handle to turn the Belt Lifter all the way to the right (clockwise) until the green arrows line up.
Optional Accessories The Floor Care System-Floor Buffer (continued)/The Floor Care System-Carpet Fluffer USING THE FLOOR BUFFER (cont) 9 Press the Toe-Touch Control™ Upper Pedal 8oto lower the brush one notch at a time. Lower the brush as far as the Toe-Touch Control will allow. With the Buffer running, move the Ultimate G over the floor as though you were cleaning a carpet, using slow, steady strokes. NOTE: The belt should not be stretched when stored for an extended period.
Optional Accessories The Floor Care System-Carpet Fluffer (continued)/ The Turbo Accessory System™ USING THE CARPET FLUFFER (cont) 3 Lower the Carpet Fluffer Nozzle one notch at a time by pushing the Toe-Touch Control™ Upper Pedal 8 . The instant the brush contacts the carpet, stop o lowering the brush. ➤ 4 Then engage TechDrive® by pressing down on the yellow “D” side of the “N/D” Pedal. You are now ready to fluff the carpet by pushing the cleaner back and forth over the carpet.
Optional Accessories The Turbo Accessory System™ (continued) TURBO-SANDING SET-UP (cont) 3 Select the correct grade of sandpaper needed for the job. Use fine paper for a smooth finish and coarse paper to clear rough surfaces or remove paint. Slide the sheet into the front clamp and lock the clamp lever. NOTE: Three grades of sandpaper come with the Sander. Each piece is a standard 1/3 sheet. ➤ 4 Tightly wrap the paper around the bottom of the Turbo Accessory and tuck the end into the rear clamp.
Optional Accessories The Turbo Accessory System™ (continued)/The Zippbrush™ TURBO POLISHING Attach the synthetic lamb’s wool pad using the same procedure as attaching sandpaper (see page 42). The Turbo Accessory now becomes a polisher. Use it for polishing hard waxed surfaces, such as table tops, paneling, large flat surfaces and cars. The Dust Shroud is not used when polishing. ❏ TURBO SCOURING Attach the webbed nylon scouring pad using the same procedure as attaching sandpaper (see page 42).
Optional Accessories The Zippbrush™ (continued) CLEANING THE ZIPPBRUSH 1 To clean the Zippbrush, press the button on the front of the brush to release the outer brush ring. 2 Lift the center Brush/Air Turbine out of the tool and remove any particles or lint from the brush and turbine. Also remove any particles left in the tool cavity. ➤ When pressing the release button, avoid placing pressure on the outer ring brush.
Operating/Maintenance Tips PART FIVE Your Kirby® Ultimate G is a highly sophisticated home maintenance system. As with most modern appliances, it requires a modest degree of routine maintenance to keep it operating efficiently. This section of the Owner’s Manual presents tips on operating and maintaining your Ultimate G.
Operating/Maintenance Tips Changing The Power Nozzle Belt CHANGING THE POWER NOZZLE BELT After extended use, the Power Nozzle Belt on your Ultimate G may become stretched and worn causing the belt to slip.(See page 11 - Brush Roll Performance Indicator Light.) If this condition exists, simply replace the old belt with a new one. NOTE: Use only approved Kirby® belts. 1 To change the belt, remove the nozzle from the Ultimate G as on page 18.
Operating/Maintenance Tips Changing The Power Nozzle Belt CHANGING THE POWER NOZZLE BELT (cont) 5 Make sure the Brush Roll Bristle Height Adjustment setting (1, 2, or 3) is the same as when the brush was removed. See page 48 for discussion of the Brush Roll Bristle Height Adjustment (1, 2, or 3). Place the belt and Brush Roll back into the nozzle. One of the plastic Brush Roll ends is larger than the other, thus the Brush Roll will only fit in the nozzle one way. Then center the belt on the Brush.
Operating/Maintenance Tips Brush Roll Bristle Height Adjustment ADJUSTING THE BRUSH ROLL HEIGHT The Brush Roll bristles wear away after long periods of use. This reduces cleaning efficiency. However, the ends of the Brush Roll are adjustable, so you can extend the bristles, allowing the brush to work like new again. The Brush Roll on a new Ultimate G has three settings: one notch, two notches and three notches. The greater the number of notches, the farther the bristles are extended.
Operating/Maintenance Tips Brush Roll Bristle Height Adjustment/Light Bulb Replacement ADJUSTING THE BRUSH ROLL HEIGHT (cont) 4 Place the brush back into the nozzle making sure both plastic Brush Roll ends are set to the same number of notches (1, 2, or 3). Replace the Rug Plate o 26 by placing it on the front of the bumper first and then pulling it over the bumper on rear of Power Nozzle o 25 . Secure the Rug Plate using the two latches that hold it in place.
Operating/Maintenance Tips Miscellaneous Parts Replacement WHEEL WEAR/ REPLACEMENT Kirby® wheels are made with a pliable tread that is designed to prevent carpet wear and prevent damage to non-carpeted floors. After extended periods of use, the tread on the wheels will wear out and the wheels will need to be replaced. Check wheel tread occasionally to determine if the wheels need to be replaced. The tread material is darker in color than the plastic wheel itself.
Operating/Maintenance Tips Questions and Answers/Troubleshooting Q WHAT IS A DOUBLE-INSULATED MACHINE? (Servicing of double-insulated appliances) A In a double-insulated appliance, two systems of insulation are provided instead of ground- ing. No grounding means is necessary on a double-insulated appliance, nor should a means for grounding be added to the appliance. A double-insulated appliance is marked with the words “DOUBLE-INSULATED” (U.S.A. and Canada).
Operating/Maintenance Tips Questions and Answers/Troubleshooting Q I SMELL BURNING RUBBER WHEN I USE MY ULTIMATE G WHAT SHOULD I DO? A 1.Check to see if the Brush Roll is turning when the Ultimate G is running. If not, then the Brush Roll may be stalled due to threads around the ends. Remove Brush Roll and make sure it rotates freely at both ends. See page 46. 2. The belt may not be fully engaged (or disengaged). Make sure the green arrows or red arrows on the Belt Lifter20o match up fully. 3.
Operating/Maintenance Tips Questions and Answers/Troubleshooting Q HOW DO I VACUUM MY UPHOLSTERED FURNITURE? A 1.Convert to a canister. See page 18. (Do not use Power Nozzle o 25 on furniture.) 2. Use the Attachment Hose with or without the following attachments: • the Upholstery Nozzle. • the Crevice Tool with the brush removed. (Use in between seat cushions and in crevices.) • the optional Zippbrush™.
Operating/Maintenance Tips Questions and Answers/Troubleshooting Q HOW DO I CLEAN OTHER HOME FURNISHINGS? A Books and Bookcases: 1. Convert to a canister. See page 18. 2. Attach the Duster Brush to the end of the Attachment Hose and “dust” the books and bookcase. 3. Other options include using an Extension Tube with the Duster Brush or the Wall & Ceiling Brush to dust the bookcase top. Lampshades and Pictures: 1. Convert to a canister. See page 18. 2. Attach the Duster Brush to the Suction Control Grip.
Consumer Relations Got a Question? Need Assistance? Your local authorized distributorship is available to answer any questions regarding your purchase or the operation of your Kirby® Home Care System. The Kirby Company also has Consumer Relations Specialists available to answer any questions you may have about the Kirby Home Care System or provide you with the name of your nearest Kirby distributor. You can contact Consumer Relations by: e-mail consumer@kirbywhq.
Kirby® Home Care Products From Your Factory Authorized Distributors and Service Centers CARPET SHAMPOO PRODUCT FAMILY Carpet Shampoo Highly effective product for deep-cleaning carpets and rugs. Carpet-safe and non-toxic. Contains KIRBY GUARD, a unique anti-resoiling ingredient. Available in 12-oz., 32-oz. and one gallon sizes. Multi-Purpose Spot Remover Ready-to-use formula for everyday stains. Just spray on stain and blot with a clean, white cloth.
Kirby® Home Care Products From Your Factory Authorized Distributors and Service Centers HARD SURFACE PRODUCT FAMILY Scuttle® Glass & Surface Cleaner A traditional Kirby favorite; great for hard surfaces such as floors, walls, countertops, appliances as well as windows, mirrors and more. Dries to a streak-free shine. 22-oz. spray bottle. Scuttle2 Antibacterial Kitchen & Bath Cleaner Cleans, deodorizes and disinfects. Kills bacteria, mold and mildew.
Index A About this Manual . . . . . . . . . . . . . 4 Accessories . . . . . . . . . . . . . . . . . 29 Accessory Lock . . . . . . . . . . . . . . 18 Air Intake Guard . . . . . . . . . . . . . 22 Attaching Bar . . . . . . . . . . . . . . . 18 Attachments . . . . . . . . . . . . . . . . 19 Attachment Hose . . . . . . . . . 18 Crevice Tool . . . . . . . . . . . . . 20 Duster Brush . . . . . . . . . . . . . 20 Extension Tubes . . . . . . . . . . 19 Inflator/Deflator . . . . . . . . . . 23 Massage Cup . . .
CE DECLARATION OF CONFORMITY We declare under our sole responsibility that, where applicable, the Model G7E vacuum cleaner is in conformity with the following standards or standardized documents. EN 55 014, EN 60 555, EN 60 335-1 and EN 60 335-2-2 in accordance with the regulations 73/23/EEC, 93/68/EEC CE 95 KIRBY® 1920 West 114th Street Cleveland, OH 44102 U.S.A. Made under one or more of the following patents and design registrations, other patents and design registrations pending.
Accessories and Attachments NOTE: View inside rear cover. No. 27 Part Recommended Uses Carpet Shampoo System Shampoo your carpet. 28 Floor Care System Floor buffer for wood or tile floors. Carpet fluffer to reset the nap on a matted-down carpet. 29 Hard Floor Pad Dust bare floors. 30 Kaddy Storage of accessories. 31 Portable Sprayer Attach onto attachment hose with unit in blower mode only to apply water-based, non-flammable liquids.
30 31 32 40 39 36 34 33 35 38 37 42 41 43 46 44 49 45 48 47
2 3 16 4 1 5 17 18 10 19 21 22 20 7 6 23 15 25 24 26 14 13 12 8 9 11 28 27 29
For assistance, contact your local Authorized Distributor. Kirby®, a division of The Scott Fetzer Co., 1920 West 114th Street, Cleveland, OH 44102, U.S.A. U.S.A./Canada Parts and Supplies: 1-800-437-7170 – imd@kirbywhq.com Consumer Relations: 1-800-494-8586 – consumer@kirbywhq.com Europe Consumer Relations 00 800 547 292 72 – consumer@kirbywhq.com www.kirby.
