User’s Manual VoIP Analog Telephone Adapter VIP-156/VIP156PE/VIP-157/VIP-157S 1
Copyright Copyright (C) 2012 PLANET Technology Corp. All rights reserved. The products and programs described in this User’s Manual are licensed products of PLANET Technology, This User’s Manual contains proprietary information protected by copyright, and this User’s Manual and all accompanying hardware, software, and documentation are copyrighted.
Revision User’s Manual for PLANET VoIP Analog Telephone Adapter: Model: VIP-156 / VIP156PE / VIP-157 / VIP-157S Rev: 5.0 (2012, March) Part No. EM-VIP_ATA_V5.
TABLE OF CONTENTS Chapter 1 Introduction ............................................................................................................ 6 U U Overview ...................................................................................................................................................... 6 U U Package Content .......................................................................................................................................... 7 U U Physical Details ...
Auto Config ....................................................................................................................................... 44 U U Management-Advanced Setting ......................................................................................................... 45 U U Tones .................................................................................................................................................. 47 U U TR-069 ........................................
Chapter 1 0B Introduction 1B 1 Overview 11B Based on years of VoIP manufacturing experiences, PLANET Technology VoIP total solutions are known for advanced implementation of standards based telephony with mass deployment capability. Cost-effective, easy-to-install and simple-to-use, the PLANET VIP-156/VIP-157/VIP-157S VoIP Phone Adapter (“ATA” in the following term) converts standard telephones to IP-based networks.
• Voice processing: Voice Active Detection, DTMF detection/ generation, G.168 echo cancellation (16mSec.), Comfort noise generation (CNG) • In band, out-of-band, and SIP-info DTMF support • IPV6 Support • TR-069 Package Content 12B The contents of your product should contain the following items: VoIP Telephone Adapter Power adapter Quick Installation Guide User’s Manual CD RJ-11 cable x 1 Physical Details 13B The following figure illustrates the front/rear panel of ATA.
Left / Right Panel of VIP-156 Front Panel of VIP-156PE Left / Right Panel of VIP-156PE 8
Front Panel of VIP-157 Left / Right Panel of VIP-157 Front Panel of VIP-157S 9
Left / Right Panel of VIP-157S LED Display & Button 19B 1 PC RJ-45 connector, to main tain the existing network structure, connected directly to the PC through straight CAT-5 cable RJ-45 connector, for Inte rnet access, connected directly to Switch/Hub through straight CAT-5 cable. 2 LAN The LAN interface also can be connected with 802.
LED display of VIP-156 / VIP-156PE LED Indicators Descriptions PWR Power is supplied to the device. STATUS The Status LED will be flashing when the machine is operational LNK/ACT OFF: the device is connected to LAN at 10Mb/s. ON: the device is connected to LAN at 100Mb/s. RING OFF: the phone is idle. ON: the phone is in use (offhook). Blinking: the phone is ringing.
Chapter 2 2B Preparations & Installation 2 Physical Installation Requirement 14B This chapter illustrates basic installation of ATA analog Phone Adapter ((“ATA” in the following term)) • Network cables. Use standard 10/100BaseT network (UTP) cables with RJ45 connectors. • TCP/IP protocol must be installed on all PCs.
ÍNote Please locate your PC in the same network segment (192.168.0.x) of ATA. If you’re not familiar with TCP/IP, please refer to related chapter on user’s manual CD or consult your network administrator for proper network configurations. LAN IP address configuration via web configuration interface 20B Execute your web browser, and insert the IP address (default: 192.168.0.1)) of VIP in the address bar.
IVR Menu Choice #111# #112xxx*xxx*xxx* xxx# #113xxx*xxx*xxx* xxx# #114xxx*xxx*xxx* xxx# #115xxx*xxx*xxx* xxx# Machine operation Set DHCP client Setup Static IP Address Parameter(s) Notes: ATA will change to DHCP None Client Use the * (star) key DHCP will be disabled and when entering a decimal system will change to the point. Static IP type. Use the * (star) key Set Network Mask when entering a decimal Must set Static IP first. point.
of the ATA. IVR will announce the current gateway IP #124# Check Gateway IP Address #125# Check Primary DNS Server Setting #126# Check LAN IP Address #128# Check Firmware Version address of the ATA. IVR will announce the current setting in the Primary DNS field. IVR will announce the current LAN port IP address of the ATA. IVR will announce the version of the firmware running on the ATA. Following keypad commands can be used to set up the main function .
Forward function disable Disable forwrad funciton enable forward to FXS Eanble forward to FXS Port Port enable forward to FXO Eanble forward to FXO Port Port #116# Enable PPTP function None Enable PPTP function #117# Disable PPTP function None Disable PPTP function #118# Enable VLAN function None Enable VLAN function #119# Disable VLAN function None Disable VLAN function #145# #146+Number# #147+Number# L Hint Please contact your Internet service provider to obtain the Internet a
Chapter 3 3B Network Service Configurations 3 Configuring and monitoring your ATA from web browser 15B The ATA integrates a web-based graphical user interface that can cover most configurations and machine status monitoring. Via standard web browser, you can configure and check machine status from anywhere around the world. Overview on the web interface of ATA 21B With web graphical user interface, you may have: More comprehensive setting feels than traditional command line interface.
VoIP Phone Adatper main page 18
Chapter 4 4B VoIP Telephone Adapter Configurations 5B 4 Status 23B Show all the system information, ex: WAN/LAN IP address, System information, IPV6 connection information, Register status and VPN connection message.
Phone Book 24B ATA can set up 140 records of Phone Book. User can dial the Name records to make calls via Phone Book feature. Field Phone Book Page Phone Description The default is Page 1. It can select Page1 ~ Page 7 to look round Phone Book records.
records in total. The name of Phone Book records, it only can input Name numerals character. Fill in the outgoing number (Line Number) or IP URL address. Delete Clean this item’s data. Export csv Save the phone book data as CSV file. Upload Upload the phone book file If you need to add a phone number into the Phone Book list, you need to input the position, the name, and the phone number (by URL type). When you finished a new phone list, just click the “Submit” button.
Call Service 25B [Call Forward] This page defines Call Forward function. You can setup the phone number you want to forward in this page. There are three type of Forward mode. You can choose All Forward, Busy Forward, and No Answer Forward by click the icon. All Forward: All incoming call will forward to the number you chosen. You can input the name and the phone number in URL field. If you select this function, then all the incoming call will direct forward to the speed dial number you choose.
All to PSTN/ No Answer to PSTN (VIP-157): VIP-157 not only support Call Forward to IP calls, but also can forward the calls to PSTN. You can choose the Call Forward type with PSTN, then input the name and the PSTN number in URL/Number field. IP Line Forward function for VIP-157 The IP Line Forward function is use for the incomin g call is IP call type, and the destinatio n is IP or PSTN call types.
[Alarm Type] This page defines the Alarm setting in this page. It provides the alarm function, and it can set up the Alarm Time to get the telephone ringed up every day. Alarm Type: The default is Off. If set up as On, the telephone will ringed up at the specific time. Alarm Time: It can set up the system prompt time with 24 hours. Alarm Line: select the Line for alarm.
Volume Settings for VIP-156T/VIP-156PT Beside the above settings, VIP-157 also can set the volume of PSTN. PSTN-Out Volume is to set the PSTN volume for you can hear. PSTN-In Gain is to set the volume send out to the other side’s handset. Volume Settings for VIP-157 Dail Plan Setting 28B This page defines the Dial Plan Setting function. This function is when you input the phone number by the keypad but you don’t need to press “#”. After time out the system will dial directly.
Dial Plan Settings for VIP-156 For VIP-157 have four more items. Field Description Drop Prefix The rule of add or replace code. If setup as Disable, it will add the prefix number prior to the identification number. If setup as Enable, it will replace the identification number. Prefix The prefix number. It only accept the numeral and the max length is 8. Rule Rule The identification number. It can accept the numeral or symbol and the max length is 40.
Dial Now rule If the dialing number are match with this field, it will dial out and need not to press the “#” key to end the dialing. It accepts the numeral or symbol, and the max length are 124. LNote: The starting number can’t be the “0”. For example, if the number is “0xxxx”, because the starting number is “0”, so that the system will ignore this dial plan. Realm 1/2/3/4/5 These options can define the switching code for each Realm No.
1. If the dialing number is “002+86xxxx”, it will ma tch the rule [002], then system will automatically replace the prefix [002] to the p refix number [006].The real dialing number is [006+8613xxxxx]. 2. If the dialing number is “003+77xxxx”, it will ma tch the rule [003], then system will automatically replace the prefix [003] to the prefix n umber [006]. The re al dialing number is [006+77xxxx]. Example_3: Drop prefix: Disable, Prefix: 009, Rule: 12 1.
Routing Type Deafult is Disable, it define the dialing route, according the [Routing Rule] to define the dialing route is [IP or FXO]. Routing Rule Define the outgong rule. It can also Add/ Drop profix number, if you want to increase more then one Routing rule, you can use “+” to except it can only press the numeric or D D: drop Example_5: Routing: Routing Type: FXO, Routing Rule: D007+009+0800 1.
Field Description Call Waiting Default is enable. When you are talking with other people, You can choose If you want to hear the notice when th ere is a ne w coming call. If the call waiting function is On, if there is a new incomeing call, you will hear the call waiting notice in your cu rrent call. If you set the function to Off, then you will not hear any notice. Ring Timeout Default is 60(sec). After how long the system will repl y the busy(486 busy) message.
Chapter 5 6B Netowrk 5 Network Settings 30B This page defines the LAN setting in this page. Field Description WAN Active The default is Fixed IP, and it also provides DHCP Client and PPPoE connection modes. Fixed IP: It could setup the IP address manual. DHCP Client: It will acquire the IP address automatically.
PPPoE AC Name PPPoE AC name. DDNS Settings 31B This page defines the DDNS setting in this page. You need to have the DDNS account and input the informations properly. You can have a DDNS account with a public IP address then others can call you via the DDNS account. But now most of the VoIP applications are work with a SIP Proxy Server. When you finished the setting, please click the Submit button.
Field Description VLAN Active If setup as On, it could receive VLAN messages. VID (802.1Q/TAG) Dispose VLAN ID is add a Tag header after realize enable the VLAN function. The realized voice packets transfer at the same VLAN. The prerequisite is it must the same as VLAN of upper switch. The value range are 2~4094. User Priority To setup the user priority. (802.1P) Field Description SIP VID Set the SIP VLAN ID, this is the independ en function don’t nee d to enable [VLAN Packets: Enable].
Caution: VIP-156/VIP-157 VPN can’t use the encryption or compression for VPN connection. U U IPV6 Settings 34B This page defines the IPV6 setting in this page, you can programm the IPV6 information. Field Description IPV6 Active Support three IPV6 type: Auto, Fixed IPV6, IPV6 in IPV4 Tunnel IPV6 address Setting the WAN IPV6 address or display it.(64 bits) SubnetPrefix Length Default is 64, settin the Default Gateway IPV6 gateway address(64 bits) LAN IPv6 Address: IP V6 LAN address.
Chapter 6 7B NAT Trans H 6 Stun Settings 35B This page defines the STUN Enable/Disable and STUN Server IP address in this page. This function can help your Phone Adapter working properly behind NAT. To change these settings please following your ISP information. When you finished the setting, please click the Submit button. PC Settings 36B This page defines the PC setting in this page. Field Description Device Active The default is Bridge mode, and it also provides NAT mode.
address. PC IP address The IP address of PC port. (In the Birdge mode, the Default IP: 192.168.0.1 PC MAC Address The MAC of PC port Enable DHCP Server It will allot the IP address automatically when enabke this function. IP Address The range for DHCP IP address. Lease Time DHCP server lease time DMZ and MAC Clone 37B This page defines the DMZ and MAC Clone setting in this page. DMZ Active: If setup as On, all of packets (expect SIP packets) will send to the specific IP address.
Field Description Index The serial number. There are total 12 records from Num 1 to 12. Active The activate status. The default is Disable, this record will been activate if enable. Protocol The TCP or UDP communication protocol. Internal Port For corresponding the internal port. External Port For corresponding the external port. Server IP To input the Server IP address.
Chapter 7 8B SIP Setting H H 7 Service Domain Settings 39B In Service Domain Function you need to input the account and the related informations in this page, please refer to your ISP provider. You can register five SIP account in the ATA. You can dial the VoIP phone to your friends via first enable SIP account and receive the phone from these five SIP accounts. Field Description Realm Which line you want to use.
LNote: The starting number can’t be the “0”. For example, if the number is “0xxxx”, because the starting number is “0”, so that the system will ignore this dial plan. You can see the Register Status in the Status page. If the item shows “Registered”, then your Phone Adapter is registered to the ISP, you can make a phone call direcly. If you have more than one SIP account, you can following the steps to register to the other ISP. When you finished the setting, please click the Submit button.
SIP Advance Setting 41B This page defines the Hold by RFC, Voice/SIP QoS and other settings in this page. To change these settings please following your ISP information. When you finished the setting, please click the Submit button.
Field Description SIP Expire Time To setup the registration interval time. SIP Expire Time Default is G eneral; Register interval time setting. Provide items Type General (standard), 1/2, 2/3, 3/4, 4/5, 5/6, 6/7, 7/8, 8/9, 9/10。 LNote: register server need support this function. Register time calculated General: expire time-[(expire time/30)*6], when Expire Time>60 it will start to work, if less then 60 seconds, it will decrease 5 seconds. 1/2: expire time * 1/2. 2/3: expire time * 2/3.
SIP Register Retry If SIP register fail, system will retry interval after this time. Timer SIP session timer T1 Setting the maximum retransmit interval for non-INVITE requests and INVITE responses. LNote: register server need support this function. SIP session timer T2 Setting the maximum retransmit interval for non-INVITE requests and INVITE responses. LNote: register server need support this function.
Class(IPV6) Use DNS SRV The default is disable, and use DNS SRV mode. Set enable t o use DNS to SRV mode to search the host information. Send Keep Alives Always to transport the network packets to keep the NAT port could be Packet opened continuous. Keep Alives Period To setup the interval time for transporting packets. Jitter Buffer To setup the size for jitter buffer packets.
Chapter 8 9B Advance Setting 8 Status Log 42B Display and saving systems running status message data, Press “Get Status Log” can backup the status log file. Auto Config 43B T This page defines the Auto Configuration (Auto Provision) setting. ATA supports TFTP, FTP, HTTP and IP PBX auto configuration function in total. In IP PBX Auto Configuration Setting you need to check with your service provider if they have provided this function.
Management-Advanced Setting 44B This page defines the advanced functions. When you finished the setting, please click the Submit button.
Field Description ICMP Not Echo This function can disable echo when someone ping this device, it can avoid hacker try to attack the device Anonymous Call If enable this function, machine will to start the calling hidden function, and it will not send the related Caller information. LNote: register server need support this function. Management form When [Enable] allow user login from WAN.
Timeout disconnection the line. PSTN CID forward It must wo rk with [Phon e – Ge neral] [Auto Answer] fun ction or [Phone – Ca ller Service] [Forwa rd] function。 When en able this function, The caller ID from FXO, can transfer to other device Generate Flash FXO flash time, define would you hold or hang on the phone Signal for PSTN FXS Port Coutry Select the FXO port local country Flash Hook Time Maximum flash time, to detect the call on hold or hang on.
auto-configuration. It also can take control of other CPE functions.
Chapter 9 10B Other Setting 9 System Authority 47B In System Authority it can change admin/System/User login password. Firmware Upgrade 48B This page defines the SIP and RTP port number in this page. Each ISP provider will have different SIP/RTPport setting, please refer to the ISP to setup the port number correctly. When you finished the setting, please click the Submit button. If your update file is xxxx.ROM. you must enter http://VIP-15X’s-IP Address/update.htm HU UHU U ex:http://192.168.0.
LNote: For technological consideration, we’ve strongly suggested refering to the following upgrade methods for update your device. After firmware loaded, the unit will be reboot, and Default IP address of the customized firmware: http://192.168.0.1 ; login name/password: root/null (no password) HU UH Auto Update Settings 49B The device can update new firmware with the gz or ds file format automatically by the Auto Upgrade function.
- Power On (+ Scheduling): The machine will check the new firmware when power on and following the scheduling date and time. - Scheduling: The machine will follow the scheduling date and time to check the new firmware. Scheduling (Date) The machine will check the new firmware between the time range by random. Automatic Update There are Notify only and Automatic ways to update.
Reset to default 50B In Default Setting you can restore the Phone Adapter to factory default in this page. You can just click the Restore button, then the Phone Adapter will restore to default and automatically restart again. Save and Reboot 51B In Save & Reboot you can save the changes you have done. If you want to use new setting in the Phone Adapter, You have to click the Save button. After you click the Save button, the Phone Adapter will automatically restart and the new setting will effect.
Appendix A Voice Communication Samples 16B There are several ways to make calls to desired destination in ATA. In this section, we’ll lead you step by step to establish your first voice communication via keypad and web browsers operations. Case 1: ATA to ATA connection via IP address 53B Assume there are two ATAs in the network the IP address are 192.168.0.1, 192.168.0.2 Analog telephone sets are connected to the phone (RJ-11) port of ATAs respectively 192.168.0.2 192.168.0.
Case 2: (Peer-to-Peer mode) VIP-157S Port 1 to Port 2 communications 54B Supposing one VIP-157S connects to two telephones, just pick up phone 1 and dial ‘192*168*0*1**5062’, phone 2 will ring. Analog telephone sets are connected to the phone (RJ-11) ports of VIP-157S respectively 192.168.0.1 1001 1 9 2 * 1 1002 6 8 * 0 * 1 * * 5 0 6 2 # Test the scenario: 1. Pick up the telephone set on VIP-157S port 1, and you should be able to hear the dial-tone 2.
Case 3: Call Forward Feature_Example 1 55B In the following samples, we’ll introduce the Call Forward Feature applications. In this example, there are three VIP-156 register to IPX-300 and VIP-156_A had set Call Forward function to VIP-156_B. Machine configuration on the VIP-156: Please log in VIP-156_A via web browser, browse to the Phone Settings menu and select the Call service config menu.
Case 4: Call Forward Feature_Example 2 56B In this example, there are one VIP-157 and two VIP-156 register to IPX-300. The VIP-157_A had set Call Forward function to phone number 1111-2222 (PSTN). Machine configuration on the VIP-157: Please log in VIP-157_A via web browser, browse to the Phone Settings menu and select the Call service config menu.
Case 5: Call Forward Feature_Example 3 57B In this example, there are one VIP-157 and two VIP-156 register to IPX-300. The VIP-157_A had set Call Forward function to number 2002 (VIP-156_B). Machine configuration on the VIP-157: Please log in VIP-157_A via web browser, browse to the Phone Settings menu and select the Call service config menu.
Case 6: Call Forward Feature_Example 4 58B In this example, there are three VIP-156 and connect with Peer to Peer mode. VIP-156_A had set Call Forward function to VIP-156_B. Machine configuration on the VIP-156: Please log in VIP-156_A via web browser, browse to the Phone Settings menu and select the Call service config menu.
Machine configuration on the VIP-157: STEP 1: Please log in VIP-157_A via web browser, browse to the Phone Settings menu and select the Call service config menu. In the setting page, please disable All Forward function, and then the sample configuration screen is shown below: STEP 2: Please log in VIP-157_A via web browser, browse to the Phone Settings / General setting menu and select the Auto Answer config menu.
6. The Phone Number 11112222 will ring up then it pick up the telephone and communication with the VIP-156_C Case 8: Auto Answer Feature_PSTN to IP 60B In this example, there are one VIP-157 and two VIP-156 and connect with Peer to Peer mode. The VIP-157_A had set Auto Answer function for forwarding to arbitrary telephone.
Test the scenario: 1. The Phone Number 11112222 pick up the telephone 2. Dial the PSTN Phone Number 33334444(VIP-157_A) 3. VIP-157_A will ring up but doesn’t answer the call 4. After 3 rings, the Phone Number 11112222 will hear the prompt sounds then input the password 123# 5. The Phone Number 11112222 will hear the dial tone then input 0# 6. The IP address 192.168.0.
Appendix B The method of operation guide 17B In this section, we’ll introduce the steps of how to set up some call features of the ATA. Please follow the steps below to utilize those features. Call Transfer 61B A. Blind Transfer 1. B call to A and they are in the process of conversation. 2. A carry the transfer function out (Press “transfer” button) to hold the conversation with B. 3. A press “#510#” and hear the dial tone, then input the number of C (Follow by the “#” key). 4.
SIP accounts incoming call, and it can switch to any one SIP accounts for making calls through input the switch code. Realm switch code: U 1*: Realm 1 2*: Realm 2 3*: Realm 3 4*: Realm 4 5*: Realm 5 For example: The default is realm 1, input the 2* (Follow by the # key) from keypad and hang up the telephone set. It will switch to realm 2, and it can make the SIP calls via realm 2. Auto Update firmware by manual (Keypad) 65B If pick up the handsetof ATA, it will hear the “DoDoDo” prompt.
Appendix C VIP-156/VIP-156PE/VIP-157/VIP-157S Specifications 18B Product Model Hardware LAN PC FXS (for telephone set connection) FXO (PSTN connection) Protocols and Standard Standard Voice codec Fax support Voice Standard Protocols Network and Configuration Access Mode Management Dimension (W x D x H) Operating Environment Power Requirement EMC/EMI SIP Analog Telephone Adapter VIP-156 VIP-156PE VIP-157 VIP-157S 1 x 10/100Mbps RJ-45 port (802.
EC Declaration of Conformity For the following equipment: *Type of Product *Model Number : SIP Telephone Adapter : VIP-156 * Produced by: Manufacturer‘s Name : Manufacturer‘s Address: Planet Technology Corp. 11F, No 96, Min Chuan Road Hsin Tien, Taipei, Taiwan, R. O.C. is herewith confirmed to comply with the requirements set out in the Council Directive on the Approximation of the Laws of the Member States relating to 1999/5/EC R&TTE.
EC Declaration of Conformity For the following equipment: *Type of Product *Model Number : PoE SIP Telephone Adapter : VIP-156PE * Produced by: Manufacturer‘s Name : Manufacturer‘s Address: Planet Technology Corp. 11F, No 96, Min Chuan Road Hsin Tien, Taipei, Taiwan, R. O.C. is herewith confirmed to comply with the requirements set out in the Council Directive on the Approximation of the Laws of the Member States relating to 1999/5/EC R&TTE.
EC Declaration of Conformity For the following equipment: *Type of Product *Model Number : VoIP Analog Telephone Adapter (1*FXS + 1*FXO) : VIP-157 * Produced by: Manufacturer‘s Name : Manufacturer‘s Address: Planet Technology Corp. 11F, No 96, Min Chuan Road Hsin Tien, Taipei, Taiwan, R. O.C.
EC Declaration of Conformity For the following equipment: *Type of Product *Model Number : VoIP Analog Telephone Adapter (2*FXS) : VIP-157S * Produced by: Manufacturer‘s Name : Manufacturer‘s Address: Planet Technology Corp. 11F, No 96, Min Chuan Road Hsin Tien, Taipei, Taiwan, R. O.C.
