Digital Camera User Manual

ManualsBrandsOlympus ManualsDigital CameraAU400

DSD/00001/7194.5

December 10, 1999

* YEAR 2000 READINESS DISCLOSURE STATEMENT *

TO OLYMPUS CUSTOMERS PRESENTLY USING:

• OLYMPUS DEMAND®, OLYMPUS® AU5000, OLYMPUS REPLY®, OLYMPUS®

AU560, OLYMPUS® AU5200, OLYMPUS® AU800, OLYMPUS® AU1000,

OLYMPUS® AU600, OLYMPUS® AU640, and OLYMPUS® AU400 Automated

Chemistry Analyzers

• OLYMPUS® PK7100 and OLYMPUS® PK7200 Automated Microplate Systems

• OLYMPUS® Aliquotting System (OASYS)

***

This Year 2000 Readiness Disclosure Statement revises, supplements, and/or restates important

information previously disseminated in our Year 2000 Readiness Disclosure Statement dated February

12, 1999 (the “February 1999 Statement”). Revised and supplemental paragraphs and sections are so

noted in this new Year 2000 Readiness Disclosure Statement. Those systems described in this

Statement as “year 2000 compliant” are year 2000 compliant in accordance with the attached Year

2000 Compliance Limited Warranty.

• OLYMPUS DEMAND Automated Chemistry Analyzer:

REVISED STATUS: A four-digit year code must be entered in the date. Entering a two-digit year

code in the date may generate an input error and prevent analysis.

• OLYMPUS AU5000 Automated Chemistry Analyzer:

REVISED STATUS:

• A four-digit year code must be entered in the date. Entering a two-digit year code in the date may

generate an input error and prevent analysis.

‚A parameter save/load function performed using the Parameter Floppy Disk after December 31,

1999 will result in the date stamp indicating the “Last Modified” status as the year “1900”.

• OLYMPUS REPLY and OLYMPUS AU560 Automated Chemistry Analyzers:

The OLYMPUS REPLY and OLYMPUS AU560 will display a year of “1900” upon transition to

January 1, 2000. OLYMPUS REPLY systems with operating software versions 2.4 and above and

OLYMPUS AU560 systems will require a special software tool to ensure year 2000 compliance.

Olympus is preparing a special software disk that must be installed in these systems. This disk will be

provided to you at no charge during the first half of 1999. Customer installation of the special

software must be performed upon initial use of the system AFTER 12:00 a.m. on January 1, 2000.

No action should be taken prior to 12:00 a.m. on January 1, 2000. Please follow the Year 2000

Conversion Instructions and Test Procedures attached to this Year 2000 Readiness Disclosure

Statement. Upon complete and correct installation of the special software provided by Olympus,

OLYMPUS REPLY and OLYMPUS AU560 units will be year 2000 compliant. NOTE: OLYMPUS

Summary of content (26 pages)

PAGE 1
December 10, 1999 * YEAR 2000 READINESS DISCLOSURE STATEMENT * • • • TO OLYMPUS CUSTOMERS PRESENTLY USING: OLYMPUS DEMAND®, OLYMPUS® AU5000, OLYMPUS REPLY®, OLYMPUS® AU560, OLYMPUS® AU5200, OLYMPUS® AU800, OLYMPUS® AU1000, OLYMPUS® AU600, OLYMPUS® AU640, and OLYMPUS® AU400 Automated Chemistry Analyzers OLYMPUS® PK7100 and OLYMPUS® PK7200 Automated Microplate Systems OLYMPUS® Aliquotting System (OASYS) *** This Year 2000 Readiness Disclosure Statement revises, supplements, and/or restates important infor
PAGE 2
REPLY systems with operating software versions below version 2.4 cannot be upgraded using the special software disk. SUPPLEMENTAL INFORMATION: After December 31, 1999, a four-digit year must be used to define the date in the OLYMPUS AU560 “SET DATE & ROUND” and OLYMPUS REPLY “SET DATE & CAROUSEL” menus. If existing data indexes have a two-digit year entry they must be searched separately from those data indexes having a four-digit year entry.
PAGE 3
that there are no initialized Data Floppy Disks available upon transition to January 1, 2000, the system date can be set to a date prior to January 1, 2000 in the “AUXILIARY/CURRENT DATE AND TIME” menu. Disks can then be initialized using the “FLOPPY INITIALIZE” menu. Should this procedure be required, the date must be returned to the then-current date and time prior to analysis in the “AUXILIARY/CURRENT DATE AND TIME” menu.
PAGE 4
• Offline Output and Data floppy disk file date stamps will be recorded on the disks as “53” during the year 2000. In addition, years subsequent to 2000 will be displayed as “54”, “55”, etc. Information stored on the disks will not be affected. File date stamps are displayed only when viewed outside the AU600 application. This condition has no impact on system functionality.
PAGE 5
° The “Cuvette Status” menu displays a yellow color to alert the operator when 8 or more days have elapsed since the last W2/Photocal operation was performed. When a W2/Photocal is performed between February 22 and February 29, the yellow color alert will not be displayed until 9 days following the date of such W2/Photocal operation. The scheduling of W2/Photocal operations during this period must be manually tracked.
PAGE 6
Director of Service Olympus America Inc. Diagnostic Systems Division Notice: This Statement contains proprietary information that is protected by copyright. All rights are reserved. No part of this document may be photocopied, reproduced, or translated to another language without the prior written consent of Olympus America Inc. MS-DOS is a U.S. registered trademark of Microsoft Corporation. DSD/00001/7194.
PAGE 7
YEAR 2000 COMPLIANCE LIMITED WARRANTY OF OLYMPUS AMERICA INC. DIAGNOSTIC SYSTEMS DIVISION EXCEPT AS DESCRIBED IN THE YEAR 2000 READINESS DISCLOSURE STATEMENT TO WHICH THIS LIMITED WARRANTY IS ATTACHED, Olympus America Inc.
PAGE 8
Limited Warranty, shall not be binding upon OAI-DSD unless reduced to writing and approved by an expressly authorized officer of Olympus America Inc. DSD/00001/7194.
PAGE 9
Year 2000 Conversion Instructions and Test Procedure OLYMPUS REPLYand OLYMPUS AU560 Automated Chemistry Analyzers Year 2000 Conversion Instructions: Note: If you wish to do a year 2000 test of the instrument please see page 5. The following items are required to perform this procedure on the Reply/AU560. Program Floppy Disk 1/3 MU5907 SPECIAL TOOL for YEAR 2000 diskette 1. Confirm that POWER ON switch on the front of the DPR is not illuminated and the analyzer and DPR are off. 2.
PAGE 10
*** SYSTEM UP *** # SELECT No.> --------------------------------------------------------------------1 DATE & TIME SET (2 SYSTEM PARAMETERS ) (3 OPTION UNIT ) (4 DATA FILE INITIALIZE ) (5 PARAMETER INITIALIZE ) 1: 2: 3: 4: 5: 6: 7: 8:PRINT FIG.2 8. Type S and the Enter ↵ key, B and the Enter ↵ key and M and the Enter ↵ key on the keyboard. Items 2 through 5 will now be displayed on the above menu.(FIG.2) 9. Type 2 and the Enter ↵ key on the keyboard.
PAGE 11
*** COPY FILES *** # SELECT No.> --------------------------------------------------------------------1. FILE COPY 2. FILE CREATE 1: 2: 3: 4: 5: 6: FIG.4 7: 8:PRINT 14. Type 1 and the Enter ↵ key on the keyboard. Wait until the DPR displays the menu shown in FIG.5. *** FILE COPY *** # SELECT No.> --------------------------------------------------------------------DEV. FILE NAME DEV. FILE NAME DEV. FILE NAME 1.MKP.SYS 2.M510SYS.
PAGE 12
CP/M-86 Version 1.0 Segment Address = F000 Last Offset = 317F CP/M86=Version 1.0 A> FIG.6 22. Type GO2000 and press the Enter ↵ key on the keyboard. (see FIG.7) A>GO2000 FIG.7 23. Wait until the DPR displays the following messages (Fig.8). A>GO2000 Transformation 2000 program for OLYMPUS Data Processor Ver.1.0 Copyright OLYMPUS OPTICAL CO.,LTD All rights reserved Translation normal end. A> FIG.8 Note: If any errors are displayed during steps 21 to 23, refer to the Appendix Error List. 24.
PAGE 13
30. No further action is required. Year 2000 Test Procedure: Use the following steps to test the change to the year 2000 and then reset to the current date. The following items are required to perform this procedure on the Reply/AU560. Program Floppy Disk 1/3 MU5907 SPECIAL TOOL for YEAR 2000 diskette 31. Confirm that POWER ON switch on the front of the DPR is not illuminated and the analyzer and DPR are off. 32. Move the BOOT switch on the rear side of the DPR from “WD” to “FD”.
PAGE 14
46. 47. 48. 49. 50. 51. 52. 53. 54. 55. 56. 57. 58. 59. 60. 61. 62. Type 2 and the Enter ↵ key on the keyboard. Type 01 for the month and the Enter ↵ key on the keyboard. Type 3 and the Enter ↵ key on the keyboard. Type 01 for the day and the Enter ↵ key on the keyboard. Press F4 (Set) to set the date and time. The date and time displayed in the upper right hand corner of the screen will reflect your changes. Press the OPS Menu key on the keyboard. The DPR displays the menu shown in FIG.1.
PAGE 15
73. 74. 75. 76. 77. 78. 79. 80. 81. 82. 83. 84. 85. 86. 87. 88. 89. 90. 91. 92. 93. 94. 95. 96. 97. 98. 99. Wait until the DPR displays the (FIG.1) menu. Type 7 and the Enter ↵ key on the keyboard. Wait until the DPR displays the (FIG.2) menu. Only Item 1 displays at this time. Type S and the Enter ↵ key, B and the Enter ↵ key and M and the Enter ↵ key on the keyboard. Items 2 through 5 will now be displayed on the (FIG.2) menu. Type 2 and the Enter ↵ key on the keyboard.
PAGE 16
A>GO2000 BACK Transformation 2000 program for OLYMPUS Data Processor Ver.1.0 Copyright OLYMPUS OPTICAL CO.,LTD All rights reserved Restore translation normal end. A> FIG.11 Note: If any errors are displayed during steps 98 to 100, refer to the Appendix Error List. 100. Remove the MU5907 SPECIAL TOOL for YEAR 2000 floppy disk. 101. Move the BOOT switch on the rear side of the DPR from “FD” to “WD”. When moving the switch, please pull out on the switch. If the switch is not pulled, it cannot be moved (FIG.
PAGE 17
Rear side of the DPR WD ‡A Â BOO ‡@ BOOT À WD ,eD FD Á FD FUSE DPR 5A ON ‡B LOCAL POWER OFF ‡C Ã FIG.9 FIG.12 Appendix: Error List Error No. Error Message 1 Parameter Error 2 or 4 Patch file [ B:INIT00.TSK] not found. 3 This system is already translated to 20xx. 5 Can't create new file [ B:INIT00.20 ]. 6 Patch strings [ 1900 ] not found in this file [B:INIT00.TSK ]. 7 This system is not translated to 20xx yet. DSD/00001/7194.5 Cause and Corrective Action The command typed was not correct.
PAGE 18
Year 2000 Conversion Instructions and Test Procedure OLYMPUS AU1000 Automated Chemistry Analyzer Year 2000 Conversion Instructions: 1. Press the Power switch on the analyzer and then press the “Q” key while the * is displayed in the upper left hand corner of the screen. The Dos C:> prompt will be displayed. 2. Type “date” and press enter↵. Follow the prompts to enter the correct date within the year 2000 and press enter↵. 3. Press the Em. Stop switch to remove power from the analyzer. 4.
PAGE 19
Year 2000 Conversion Instructions and Test Procedure OLYMPUS AU5200 Automated Chemistry Analyzer Year 2000 Conversion Instructions: 1. From the Ops Menu select 21. Auxilliary Menu then select 8. Current Date and Time. 2. In this menu press the Enter key for the Year, Month, Day, Hour, Minute and Day of Week. This menu will have the updated date already. 3. Press the Yes key at the # All Ok ? (Yes,No) > __ prompt. The display will now be correct. No further action is required.
PAGE 20
Year 2000 Conversion Instructions and Test Procedure OLYMPUS AU600 Automated Chemistry Analyzer Year 2000 Conversion Instructions: 12. Press the Power switch on the analyzer and then press the “Q” key while the * is displayed in the upper left hand corner of the screen. The System Maintenance Menu will be displayed. 13. Type “14” and press enter↵ to select option 14. Go to DOS. 14. Type “date” and press enter↵. Follow the prompts to enter the correct date within the year 2000 and press enter↵. 15.
PAGE 21
24. Press the Em. Stop switch to remove power from the analyzer. Press the Reset switch and then the Power switch to restore power and load the program on the analyzer. Check that the current date is displayed in the upper right corner of the screen. No further action is required. DSD/00001/7194.
PAGE 22
Year 2000 Conversion Instructions and Test Procedure OLYMPUS PK7200 Automated Microplate System Year 2000 Conversion Instructions: 14. Power on the instrument using the Power On switch on the front of the DPR. ***OPERATION MENU*** # SELECT No.> _____________________________________________________________ 1 START CONDITION 2 TEST REQUISITION 3 TEST DATA DISPLAY 4 ANALYZER STATUS 5.SAMPLE LIST 6 DATA MANAGEMENT 7 REPORT 1: 2: 3:WARM 4: 8 DATA…… 9 QC 5:DIAG 6: 21…… 22…… 7:END 8: 15.
PAGE 23
_____________________________________________________________ 1 DATE MARK 19 2 DATE & TIME SET 3 CLEANING DRIVE 1: 2: 3: 4: 5: 6: 7: 8: 17. In the Maintenance (DPR) menu select 1, Date Mark, then press enter ↵. 18. Type 20 and press enter↵. 19. The date and time will be properly displayed and updated in the upper right corner of the CRT. No further action is required. Year 2000 Test Procedure: Use the following steps to test for the change to the year 2000 and then reset to the current date. 20.
PAGE 24
1 DIAGNOSTIC (DPR) 2 DIAGNOSTIC (DPR) 3 DIAGNOSTIC (DPR) 4 DIAGNOSTIC (DPR) 5 MAINTENANCE (DPR) 6 MAINTENANCE (ANL) 7 MANUAL MEASURE 1: 2: 3:WARM 4: 5: 6: 7:END 8: 22. Select 5, Maintenance (DPR) and press enter ↵. *** 5 MAINTENANCE (DPR) *** # SELECT No.> _____________________________________________________________ 1 DATE MARK 19 2 DATE & TIME SET 3 CLEANING DRIVE 1: 2: 3: 4: 5: 6: 7: 8: 23. In the Maintenance (DPR) menu select 1, Date Mark, then press enter ↵. 24. Type 20 and press enter↵.
PAGE 25
2 DIAGNOSTIC (DPR) 3 DIAGNOSTIC (DPR) 4 DIAGNOSTIC (DPR) 5 MAINTENANCE (DPR) 6 MAINTENANCE (ANL) 7 MANUAL MEASURE 1: 2: 3:WARM 4: 5: 6: 7:END 8: 28. Select 5, Maintenance (DPR) and press enter ↵. *** 5 MAINTENANCE (DPR) *** # SELECT No.> _____________________________________________________________ 1 DATE MARK 19 2 DATE & TIME SET 3 CLEANING DRIVE 1: 2: 3: 4: 5: 6: 7: 8: 29. In the Maintenance (DPR) menu select 1, Date Mark, then press enter ↵. 30. Type 19 and press enter↵. 31.
PAGE 26
Year 2000 Conversion Instructions and Test Procedure OLYMPUS AU800 Automated Chemistry Analyzer Year 2000 Conversion Instructions: 25. Press the Power switch on the analyzer and then press the “Q” key while the * is displayed in the upper left hand corner of the screen. The Dos C:> prompt will be displayed. 26. Type “date” and press enter↵. Follow the prompts to enter the correct date within the year 2000 and press enter↵. 27. Press the Em. Stop switch to remove power from the analyzer. 28.