SmartSwitch 9500 9A656-04 ATM Module Hardware and Installation Guide 9032031-01
Notice Notice Cabletron Systems reserves the right to make changes in speciÞcations and other information contained in this document without prior notice. The reader should in all cases consult Cabletron Systems to determine whether any such changes have been made. The hardware, Þrmware, or software described in this manual is subject to change without notice.
Notice FCC Notice This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules.
Notice Declaration of Conformity Application of Council Directive(s): ManufacturerÕs Name: ManufacturerÕs Address: European Representative Name: European Representative Address: Conformance to Directive(s)/Product Standards: Equipment Type/Environment: 89/336/EEC 73/23/EEC Cabletron Systems, Inc. 35 Industrial Way PO Box 5005 Rochester, NH 03867 Mr. J.
Notice iv
Contents Chapter 1 Introduction Document Objectives.................................................................................................... 1-1 Overview ........................................................................................................................ 1-2 Features........................................................................................................................... 1-4 Processor ..........................................................................
Contents Chapter 4 LANVIEW LEDs ANIM LEDs ............................................................................................................ 4-3 Chapter 5 General Specifications Operating SpeciÞcations .............................................................................................. 5-1 Environmental Requirements .............................................................................. 5-1 Regulatory Compliance..................................................................
Chapter 1 Introduction Document Objectives This document, the SmartSwitch 9500 9A656-04 ATM Module Hardware and Installation Guide, contains introductory, installation and speciÞcation information for the support of the 9A656-04 SmartSwitch Module.
Introduction Overview The 9A656-04 (shown in Figure 1-1) is a 4.5 Gbps, single slot module for the SmartSwitch 9500 chassis. Up to four ATM Network Interface Modules (ANIMs) of any type can be plugged into the 9A656-04 to provide front panel connectivity to the network. Cabletron Systems ANIMs can support up to 622 Mbps of bandwidth per port. The 9A656-04 switches data between the ANIMs and the Cell Transfer Matrix (CTM) backplane in the SmartSwitch 9500 chassis.
AN AN AN AN Overview 2031_01 Figure 1-1.
Introduction Features The features of the 9A656-04 are described in the sections below: Processor The 9A656-04 is equipped with an advanced Intel i960 microprocessor. This microprocessor provides signalling, SNMP management, and serves as the in-band management LAN Emulation Client (LEC). Cabletron Systems ASICs The 9A656-04 contains Þve different Cabletron Systems designed ASICs that provide a variety of switching services. For more information on these ASICs refer to Chapter 3.
Related Manuals LANVIEW LEDs The 9A656-04 uses LANVIEW, The Cabletron Systems built-in visual diagnostic and status monitoring system. With LANVIEW LEDs, you can quickly identify the device, port, and physical layer status at a glance. Related Manuals The manuals listed below should be used to supplement the procedures and technical data contained in this manual.
Introduction Getting Help For additional support related to this device or document, contact the Cabletron Systems Global Call Center: Phone (603) 332-9400 Internet mail support@ctron.com FTP Login Password ctron.com (134.141.197.25) anonymous your email address Modem setting (603) 335-3358 8N1: 8 data bits, No parity, 1 stop bit BBS For additional information about Cabletron Systems or its products, visit the World Wide Web site: http://www.cabletron.
Chapter 2 Installing the 9A656-04 Module SmartSwitch 9500 modules can be installed in any of the slots that are available. To install a module, proceed as follows: ! Observe all antistatic precautions when handling sensitive electronic equipment. CAUTION ! 1. Remove the blank plate covering the slot in which the 9A656-04 will be installed. All other slots must remain covered to ensure proper airßow and cooling. (Save the blank plate in the event you need to remove the module.) 2.
Installing the 9A656-04 Module AN AN AN AN Plastic Locking Tab Plastic Locking Tab Metal Back-Panel Circuit Card Card Guides 2031_02 Figure 2-1.
The Reset Switch The Reset Switch ! CAUTION Resetting the 9A656-04 will cause a brief period of system downtime. When the interface module is reset, the remaining modules attached to the CTM go through an initialization process to determine which interface module will become the module that performs specific management functions. The Reset switch is located on the front panel, under the top plastic tab as shown in Figure 2-2.
Installing the 9A656-04 Module The Module Card DIP Switch An eight position DIP switch is located on the module card as shown in Figure 2-3. The functions of the switches are listed in Table 2-1. ! Do not toggle Switch 8 unless you intend to reset the user configured passwords to their factory default settings. CAUTION Do not toggle Switch 7 unless you intend to reset the user parameters to the factory default settings.
Installing an ANIM Installing an ANIM Figure 2-3 shows the location of the 4 motherboard connectors, and the 16 standoff screws for the ATM Network Interface Modules (ANIMs). Figure 2-3 also shows the location of the Module Card DIP Switch. i960 Processor ANIM Connectors (4) Standoff Screws (16) 2031_04 DIP Switch 8 7 6 5 4 3 2 1 Figure 2-3.
Installing the 9A656-04 Module ! CAUTION NOTE The ANIM and 9A656-04 module are sensitive to static discharges. Use a grounding strap and observe all static precautions during this procedure. Failure to do so could damage the ANIM and the 9A656-04 module. If you are installing ANIMs in more than one slot, remove the cover plates from all the associated slot openings. A Phillips Head screwdriver is needed to install the ANIMs. The 9A656-04 module is shipped without ANIMs.
Installing an ANIM ! When installing or removing an ANIM make sure to always use the cutouts on the board to handle the ANIM. See Figure 2-6 for the location of the cutouts. CAUTION When connecting the ANIM pins to the motherboard connector take extra precaution that the pins do not enter the connector at an angle as this will damage both the ANIM and the motherboard connector. 5. Press straight down Þrmly on the ANIM until the pins slide all the way into the motherboard connector.
Installing the 9A656-04 Module 2-8
Chapter 3 Operation The 9A656-04 provides switching between the front panel interfaces (ANIMs) and the Cell Transfer Matrix backplane located inside the SmartSwitch 9500 chassis. Figure 3-1 shows the trafÞc ßow of ATM cells in the 9A656-04. The following sections brießy describe the functions of the i960 Processor, the ASICs, the CTM and how they relate to ATM cell trafÞc ßow.
Operation ATM Cell Traffic Flow in the 9A656-04 The 9A656-04 SmartSwitch utilizes several innovative features that result in a completely redundant, fault-tolerant design. The three most important hardware facets of the 9A656-04 SmartSwitchÕs features are the Cell Transfer Matrix, Cabletron Systems ASICs, and the i960 HD RISC Processor. Cell Transfer Matrix (CTM) The Cell Transfer Matrix provides a Time Division Multiplexed (TDM) based mesh of full duplex, high-speed (1.
ATM Cell Traffic Flow in the 9A656-04 CTM (Cell Transfer Matrix) ASICs The 9A656-04 has seven CTM ASICs that provide two interfaces each between the TDM Bus and the CTM Backplane located in the SmartSwitch 9500 chassis. Each interface is a full-duplex connection with a raw throughput capacity of 2 Gbps. In addition, the CTM ASICs perform all trafÞc management between the 9A656-04 and the CTM backplane.
Operation System Management Buses There are two management channels within the SmartSwitch 9500 system: ¥ ¥ SMB-1 SMB-10 These buses provide out-of-band management and inter-module management communication. SMB-1 Bus The SMB-1 is a 1 Mbps management bus located within the SmartSwitch 9500 chassis.
System Diagnostic Controller System Diagnostic Controller This diagnostic controller is composed of a Z-80 microprocessor and its supporting logic.
Operation 3-6
Chapter 4 LANVIEW LEDs The front panel LANVIEW LEDs indicate the status of the module and may be used as an aid in troubleshooting. Shown in Figure 4-1 are the LANVIEW LEDs of the 9A656-04 module. Refer to Table 4-1 for the full deÞnitions of 9A656-04 LED states. 9A656-04 SMB Status System Status 2031_09 Figure 4-1.
LANVIEW LEDs Table 4-1. SMB and CPU LEDs LED SMB CPU 4-2 LED Color State DeÞnition Green Functional Fully operational Amber Crippled Not fully operational (i.e.
ANIM LEDs The front panel LANVIEW LEDs indicate the status of the ANIM and may be used as an aid in troubleshooting. Shown in Figure 4-2 are the LANVIEW LEDs of all ANIMs. Although there are several types of ANIMs, all share the same LANVIEW LEDs. Refer to Table 4-2 for the full deÞnitions of ANIM LED states. ATM Link ATM Status 2031_10 Figure 4-2. ANIM LEDs Table 4-2.
LANVIEW LEDs 4-4
Chapter 5 General Specifications The speciÞcations for the 9A656-04 are detailed in the sections that follow. Operating Specifications Environmental Requirements Operating Temperature Storage Temperature: Operating Relative Humidity: 5¡C to 40¡C (41¡F to 104¡F) -30¡C to 73¡C (-22¡F to 164¡F) 5% to 90% (non-condensing) Regulatory Compliance Safety This equipment meets the safety requirements of UL 1950, CSA C22.2 No. 950, EN 60950, IEC 950 and 73/23/EEC.
General Specifications Physical Dimensions 35.0 D x 44.0 H x 3.0 W centimeters (13.8 D x 17.4 H x 1.2 W inches) Weight Unit: 1.36 kg. (3lb) Shipping: 1.81 kg. (4lb) Device Specifications Processor Intel i960HD RISC processor control Dynamic Random Access Memory (DRAM) 96 MB FLASH Memory 8 MB ANIM Specifications The 9A656-04 uses ATM Network Interface Modules (ANIMs) to provide front panel cable connections. The ANIMs should be installed by qualiÞed personnel.
ANIM Specifications ANIM-21/3 The ANIM-21/3 provides a multimode Þber connection using a Duplex SC connector and a line rate of 155.52 Mbps. The speciÞcations for the ANIM-21/3 are listed in Table 5-1. Table 5-1. ANIM-21/3 Specifications Parameter SpeciÞcation Number of Interfaces 3 Line Rate 155.52 Mbps Interface Type Duplex SC Media Type Multimode Fiber Frame Type SONET/SDH Typical Range 2 km TX -17 db to -12 db Loss Budget RX -27 db to -12 db 2031_11 Figure 5-1.
General Specifications ANIM-29/3 The ANIM-29/3 provides a single mode Þber connection using a Duplex SC connector with a line rate of 155.52 Mbps. The speciÞcations for the ANIM-29/3 are listed in Table 5-2. Table 5-2. ANIM-29/3 Specifications Parameter SpeciÞcation Number of Interfaces 3 Line Rate 155.52 Mbps Interface Type Duplex SC Media Type Single mode Fiber Frame Type SONET/SDH Typical Range 15 km TX -15 db to -8 db Loss Budget RX -31 db to -8 db 2031_11 Figure 5-2.
ANIM Specifications ANIM-29/3LR The ANIM-29/3LR provides a single mode Þber connection using a Duplex SC connector with a line rate of 155.52 Mbps. The speciÞcations for the ANIM-29/3LR are listed in Table 5-3. Table 5-3. ANIM-29/3LR Specifications Parameter SpeciÞcation Number of Interfaces 3 Line Rate 155.52 Mbps Interface Type Duplex SC Media Type Single mode Fiber Frame Type SONET/SDH Typical Range 60 km TX -15 db to -8 db Loss Budget RX -31 db to -8 db 2031_11 Figure 5-3.
General Specifications ANIM-31/2 The ANIM-31/2 provides a multimode Þber connection using a Duplex SC connector with a line rate of 622 Mbps. The speciÞcations for the ANIM-31/2 are listed in Table 5-4. Table 5-4. ANIM-31/2 Specifications Parameter SpeciÞcation Number of Interfaces 2 Line Rate 622 Mbps Interface Type Duplex SC Media Type Multimode Fiber Frame Type SONET/SDH Typical Range 2km TX -19 db to -14 db Loss Budget RX -26 db to -14 db 2031_12 Figure 5-4.
ANIM Specifications ANIM-39/2 The ANIM-39/2 provides a single mode Þber connection using a Duplex SC connector with a line rate of 622 Mbps. The speciÞcations for the ANIM-39/2 are listed in Table 5-5. Table 5-5. ANIM-39/2 Specifications Parameter SpeciÞcation Number of Interfaces 2 Line Rate 622 Mbps Interface Type Duplex SC Media Type Single mode Fiber Frame Type SONET/SDH Typical Range 15 km TX -15 db to -8 db Loss Budget RX -28 db to -7 db 2031_12 Figure 5-5.
General Specifications ANIM-39/2LR The ANIM-39/2LR provides a single mode Þber connection using a Duplex SC connector with a line rate of 622 Mbps. The speciÞcations for the ANIM-39/2LR are listed in Table 5-6. Table 5-6. ANIM-39/2LR Specifications Parameter SpeciÞcation Number of Interfaces 2 Line Rate 622 Mbps Interface Type Duplex SC Media Type Single mode Fiber Frame Type SONET/SDH Typical Range 60 km TX -15 db to -8 db Loss Budget RX -28 db to -7 db 2031_12 Figure 5-6.
ANIM Specifications ANIM-67/2 The ANIM-67/2 provides a coaxial cable connection using BNC connectors with a line rate of 45 Mbps. The speciÞcations for the ANIM-67/2 are listed in Table 5-7. Table 5-7. ANIM-67/2 Specifications Parameter SpeciÞcation Number of Interfaces 2 Line Rate 45 Mbps Interface Type BNC Media Type Coaxial Cable Frame Type DS3 Typical Range 185 meters 2 Figure 5-7.
General Specifications ANIM-77/2 The ANIM-77/2 provides a coaxial cable connection using BNC connectors with a line rate of 34 Mbps. The speciÞcations for the ANIM-77/2 are listed in Table 5-8. Table 5-8. ANIM-77/2 Specifications Parameter SpeciÞcation Number of Interfaces 2 Line Rate 34 Mbps Interface Type BNC Media Type Coaxial Cable Frame Type E3 Typical Range 185 meters 2 Figure 5-8.
ANIM Specifications ANIM-22/4 The ANIM-22/3 provides a Category 5 UTP connection using four RJ45 connectors with a line rate of 155.52 Mbps. The speciÞcations for the ANIM-22/4 are listed in Table 5-9. Table 5-9. ANIM-22/4 Specifications Parameter SpeciÞcation Number of Interfaces 4 Line Rate 155.52 Mbps Interface Type RJ45 Media Type Category 5 UTP Frame Type SONET/SDH Typical Range 100 meters Figure 5-9.
General Specifications 5-12
