Operation Manual

51 En
Changing various settings of this unit (SETUP menu)
English
INTRODUCTION
ADDITIONAL
INFORMATION APPENDIX
PREPARATION
BASIC
OPERATION
ADVANCED
OPERATION
■ Aspect
Sets a horizontal to vertical ratio (aspect ratio) of images
reproduced by HDMI signals output from the HDMI OUT
jack when the HDMI signals are converted from analog
video input signals by a video conversion function.
Notes
• You cannot change the aspect ratio of the screen when “Resolution” is set
to “Through.”
• The setting is not effective for inputs with the aspect ratio other than 4:3.
• You cannot obtain an effect of the aspect ratio when video signals are
input from the HDMI 1-4 jacks or 720p, 1080i or 1080p signals are input.
You can change some parameters for a monitor or the
front panel display.
■
Dimmer
Sets brightness of the front panel display. As the value is
lowered, the brightness of the front panel display is
darkened.
Note
• The brightness of display does not become bright in Pure Direct mode
even if the value is increased.
■ FL Scroll
Selects the way to scroll the screen when a total number of
characters exceed a display area of the front panel display.
■
OSD Shift
Adjusts top and bottom positions of the OSD (on-screen
display) menus. To move up the screen, set this value
larger. To move down the screen, set it smaller.
You can change some parameters for volumes.
■
Adaptive DRC
Adjusts the dynamic range in conjunction with the volume
level. This function is useful when you are listening at
lower volumes or at night. When this function is enabled,
the dynamic range is adjusted as follows.
If the volume setting is low:
the dynamic range is narrow
If the volume setting is high:
the dynamic range is wide
y
• The “Adaptive DRC” setting is effective for headphones.
■ Max Volume
Sets the maximum volume level so that the volume will
not be accidentally increased. For example, you can adjust
the volume between –80.0 dB and –5.0 dB or mute when
you set this parameter to “–5.0dB.” The volume increases
to the maximum level when this parameter is set to
+16.5 dB (default).
■
Init. Volume
Sets the volume at the time this unit is turned on. When
this parameter is set to “Off,” the volume is set to a level
that last time this unit is set to standby.
Note
• If the setting of “Max Volume” is lower than the setting of “Init.
Volume,” the setting of “Max Volume” becomes effective. For example,
when you set “Max Volume” to “–30.0dB” and “Init. Volume” to
“0.0dB,” the volume is automatically set to “–30.0dB” at the next time
this unit is turned on.
Choices: Thrgh*/16:9/Smart
Thrgh Outputs the video signals without changing
the aspect ratio.
16:9 Outputs the video signals that displays 4:3
images on a 16:9 monitor with black bands
on the right and left sides of the monitor
screen.
Smart Outputs the video signals that displays 4:3
images on a 16:9 monitor by stretching right
and left of images to fit on the monitor
screen.
2Display
Adjustable range: -4 to 0*
Choices: Continue*/Once
Continue Repeatedly displays all characters by
scrolling.
Once Displays all characters by scrolling once,
halts scrolling, and then displays first 14
characters.
Adjustable range: -5 to 0* to +5
3Volume
Choices: Auto/Off*
Auto Adjusts the dynamic range automatically.
Off Does not adjust the dynamic range
automatically.
Adjustable range: -30.0dB to +15.0dB/+16.5dB* (5.0 dB
steps)
Choices: Off*/Mute/-80.0dB to +16.5dB (0.5 dB steps)
Volume: highVolume: low
Input levelInput level
Output level Output level
Auto
Off Off
Auto