USB 2.0 1-to-2 Standalone Flash Drive Duplicator USBDUP12 *actual product may vary from photos DE: Bedienungsanleitung - de.startech.com FR: Guide de l'utilisateur - fr.startech.com ES: Guía del usuario - es.startech.com IT: Guida per l'uso - it.startech.com NL: Gebruiksaanwijzing - nl.startech.com PT: Guia do usuário - pt.startech.com For the most up-to-date information, please visit: www.startech.
FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Table of Contents Introduction.............................................................................................1 Packaging Contents.................................................................................................................................. 1 Front..........................................................................................................2 Back...........................................................................................................
6.3.2 H5 R/W 100%..................................................................................................................................... 10 6.3.3 Setup Range...................................................................................................................................... 10 6.3.4 Setup Error Limit.............................................................................................................................. 10 6.4 Quick Erase...................................
Introduction The USBDUP12 USB 2.0 1:2 Standalone Flash Drive Duplicator offers a quick and easy solution for duplicating/cloning a USB flash drive to one or two target USB flash drives without connecting to a computer system. Featuring high performance duplications at up to 1.5GB per minute, the flash drive copier has a lightweight design, and user friendly interface using the integrated LCD display.
Front Forward LCD OK USB Master Port ESC Backward Signal LED USB Target Port Back DC Power Port Instruction Manual 2 Power Switch
How to Use Menu Options 1. Copy 2. Compare 3. Copy + Compare 4. Capacity Check 5. Information 5.1 USB Info 5.2 System Info 6. Utility 6.1 Format 6.1.1 Auto Format 6.1.2 FAT Format 6.1.3 FAT32 Format 6.2 Measure Speed 6.3 Media Check 6.3.1 H3 Sake 100% 6.3.2 H5 RW 100% 6.3.3 Setup Range 6.3.4 Setup Error Limit 6.4 Quick Erase 6.5 Full Erase 6.6 DoD Erase 6.7 System Update 6.8 Calc.
Menu Options (Continued) 7. Setup 7.1 Start-up Menu 7.2 Copy Area 7.2.1 System and Files 7.2.2 Whole Media 7.3 Button Beep 7.4 Asynchronous Hold Time 7.5 Target Tolerance 7.6 Asynchronous Mode 7.7 Check Before Copy 7.8 Power Off Time Between Copy + Compare 7.9 Language 7.10 Working Mode 7.11 Set HDD Mode 7.
1. Copy There are two types of copy modes, Asynchronous Copy and Synchronous Copy. The system will check the content size of the source before executing the ‘copy’ function. If the source content size is less than the system’s buffer memory, it will automatically start an Asynchronous copy. If the source content size is larger than the system’s buffer memory, it will copy in Synchronous mode. 1.1 Synchronous Copy To configure, go to function “7.6 Asynchronous” and select “Disable”.
NOTE: a. When the copy is in progress, the green LED will flash for each Flash drive that is connected. When the copy has finished, the green LED will stop flashing and remain illuminated. If an error occurs, the red LED will illuminate. b. Do NOT remove the Flash drives while the system is copying (green LED is flashing). You can cancel a duplication by pressing ESC. c. It is recommended that the source and destination are the same size.
NOTE: a. When the copy is in progress, the green LED will flash for each Flash drive that is connected. When the copy has finished, the green LED will stop flashing and remain illuminated. If an error occurs, the red LED will illuminate. b. Do NOT remove the Flash drive while the system is copying (green LED is flashing). c. Once the copy process has completed (green LED is solid), you can then take out that Flash drive and insert a new one. d.
1 2 3 [#2] SIZE: 1847M Capacity 0K [#3] SIZE: 1847M Wrong Size: 752M Green Light: Correct Size Red Light: Wrong Size NOTE: a. This function may change the data and format on the Flash drive. b. To protect the source drive’s data, the system does not check the capacity of the source drive. c. If the red LED illuminates indicating an error, you can use the up and down arrows for error information. 5. Information 5.1 USB Info.
6. Utility 6.1 Do Format 6.1.1 Auto Format Insert a Flash drive device into one of the destination slots and press OK to begin formatting. 1. This function will automatically detect the capacity of the Flash drive and format accordingly. If the Flash drive is already FAT16 or FAT32, the original format will not be changed. 2. If the Flash drive’s format is NTFS, Linux, or multi-partition FAT, the system will format the drive according to the capacity.
6.3 Media Check Analyze the Flash drive’s quality. There are two types of methods to check the drive, ‘H3 Safe’ and ‘H5 R/W’. Before starting a quality check, you can change the range and error limit using functions ‘6.3.3 Setup Range’ and ‘6.3.4 Set Error Limit’ respectively. 6.3.1 H3 Safe 100% Check the Flash drive’s quality by reading the drive. After the process has completed, the LCD display will show the volume of bad sectors detected, and the read speed of the drive. 6.3.
6.5 Full Erase Erase the Flash drive’s content and format. 6.6 DoD Erase This function complies with the U.S.A Department of Defense (DoD 5220) standard to fully erase the Flash drive three times to guarantee the data has been deleted. NOTE: The source drive will not be formatted. 6.7 System Update Update the system’s firmware version. Save the firmware update onto your Flash drive. Make sure the firmware update file is un-zipped and not in a folder. To start, press OK on “6.
7.3 Button Beep Turn audio feedback ON/OFF. ON by default. 7.4 Asyn Hold time Set the time to cancel an Asynchronous copy when you’ve temporarily finished copying and all of the Flash drive devices have been removed, but the copy job has not been manually cancelled. This is to prevent mistakenly overwriting your source drive when you’d like to start a new source copy but the previous Asynchronous copy job has not yet been cancelled. The default is 30 seconds.
7.10 Working Mode There are 5 duplication speeds: • Slowest Mode • Slower Mode • Normal Mode (default setting) • Faster Mode • Fastest Mode Change the duplication speed. Normal speed is recommended for most Flash drive types. If there is a high failure rate when duplicating, try lowering the speed. 7.11 Set HDD Mode Choose ‘Active Mode’ to duplicate to USB Hard Disk Drives (HDD/SSD). Choose ‘Inactive Mode’ to duplicate USB Flash drives. Inactive mode is set by default. 7.
Specifications Number of Ports 3 (1 x Source, 2 x destination) External Connectors 3 x USB 2.0 type A female Duplication Rate Up to 1.5GB/m Media Supported USB 1.1/ USB 2.
Technical Support StarTech.com’s lifetime technical support is an integral part of our commitment to provide industry-leading solutions. If you ever need help with your product, visit www.startech.com/support and access our comprehensive selection of online tools, documentation, and downloads. For the latest drivers/software, please visit www.startech.com/downloads Warranty Information This product is backed by a two year warranty. In addition, StarTech.
Hard-to-find made easy. At StarTech.com, that isn’t a slogan. It’s a promise. StarTech.com is your one-stop source for every connectivity part you need. From the latest technology to legacy products — and all the parts that bridge the old and new — we can help you find the parts that connect your solutions. We make it easy to locate the parts, and we quickly deliver them wherever they need to go. Just talk to one of our tech advisors or visit our website.
