USER GUIDE 8 Cu. Ft. Electric and Gas Dryers with Steam and Sensor Dry NS-FDRG80W3/NS-FDRE80W3 Before using your new product, please read these instructions to prevent any damage.
Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Package contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SAFETY & PRECAUTIONS 8 Cu. Ft. Electric and Gas Dryers Introduction Congratulations on the purchase of your new Insignia dryer. Insignia dryers feature the latest in design and capabilities and will provide reliable and trouble-free performance. IMPORTANT SAFETY INSTRUCTIONS READ AND KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE This manual contains important information on the installation, use, and care of your appliance.
SAFETY & PRECAUTIONS NS-FDRG80W3/NS-FDRE80W3 The level of risk is shown by the following indications. WARNING This symbol indicates the possibility of death or serious injury. CAUTION This symbol indicates the possibility of injury or damage to property. WARNING This symbol indicates the possibility of dangerous voltage constituting a risk of electrical shock is present that could result in death or serious injury.
SAFETY & PRECAUTIONS 8 Cu. Ft. Electric and Gas Dryers WARNING To reduce the risk of fire, electric shock, or injury to persons when using your appliance, follow basic precautions, including the following: • Read all instructions before using the appliance. • Use this appliance only for its intended purpose as described in this User Guide. • Before use, the dryer must be properly installed as described in this User Guide. • ALWAYS follow the fabric care instructions supplied by the garment manufacturer.
SAFETY & PRECAUTIONS NS-FDRG80W3/NS-FDRE80W3 • Keep the area around the exhaust opening and surrounding areas free from lint, dust, and dirt. • The interior of the dryer and exhaust duct should be cleaned periodically by qualified service personnel. • Do not place items exposed to cooking oils in your dryer. Items contaminated with cooking oils may contribute to a chemical reaction that could cause a load to catch fire. • This appliance must be grounded.
INSTALLATION INSTRUCTIONS 8 Cu. Ft. Electric and Gas Dryers • Take care that fingers are not caught in door when closing it. This may result in injury. • Gas leaks may occur in your system, resulting in a dangerous situation. • Gas leaks may not be detected by smell alone. • Gas suppliers recommend you purchase and install a UL approved gas detector. SAVE THESE INSTRUCTIONS THIS APPLIANCE IS FOR HOUSEHOLD USE ONLY. Features Package contents • • • • 8 Cu. Ft.
INSTALLATION INSTRUCTIONS Back components Electric Dryer Wiring box Water inlet Back venting hole Gas Dryer Power cord (gas dryer only) Gas inlet Water inlet 8 www.insigniaproducts.
INSTALLATION INSTRUCTIONS 8 Cu. Ft. Electric and Gas Dryers Unpacking your dryer WARNING: • Packing materials can be dangerous to children. Keep all packing materials (such as plastic bags and polystyrene) out of the reach of children. • Unpack your dryer and inspect it for shipping damage. Make sure that you have received all the items shown in Package contents on page 7. • To prevent personal injury or strain, wear protective gloves and use a furniture mover whenever lifting or carrying your dryer.
INSTALLATION INSTRUCTIONS • Do not install or store your dryer in an area where it will be exposed to water or weather. Keep the dryer area clear of combustible materials, gasoline, and other flammable vapors and liquids. Your dryer produces combustible lint. Keep the area around your dryer lint-free. 39 13/16 in. (101 cm) 27 in. (68.6 cm) 10 www.insigniaproducts.
INSTALLATION INSTRUCTIONS 8 Cu. Ft. Electric and Gas Dryers 33 3/4 in. (85.6 cm) 39 13/16 in. (101 cm) 55 1/4 in. 140.2 cm Installing side-by-side, or in an alcove, closet, or other recessed area WARNING: • You must exhaust your dryer to the outside to reduce the risk of fire when installed any place inside the house. • Do NOT install another fuel-burning appliance in the same closet as your dryer. • For information about how to select and install exhaust ducts, see Exhausting requirements on page 15.
INSTALLATION INSTRUCTIONS Installing in a closed cabinet Minimum clearances between your dryer and adjacent walls or other surfaces are: • Either side: 1 in. (2.5 cm) • Rear: 5 in. (12.7 cm) • Top: 24 in. (61 cm) • Front: 2 in. (5.1 cm) 39 13/16 in. (101 cm) 1 in. (2.5 cm) 27 in. (68.6 cm) 1 in. (2.5 cm) 24 in. (61.0 cm) 2 in. (5.1 cm) 12 33 3/4 in. (85.6 cm) 5 in. (12.7 cm) www.insigniaproducts.
INSTALLATION INSTRUCTIONS 8 Cu. Ft. Electric and Gas Dryers Note: Your dryer can be installed in either the left or right side of the cabinet. 1.01in.in.(2.5 (2.5cm) cm) 1 in. (2.5 cm) 27 in. (68.6 cm) www.insigniaproducts.com 1 in. (2.
INSTALLATION INSTRUCTIONS Installing stacked with a washer Note: The front of the closet must have two unobstructed air openings for a combined minimum total area of 72 sq. in. (465 sq. cm) with a minimum clearance of 3 in. (76 mm) at the top and bottom. A slatted door with equivalent space clearance is acceptable. 6 in. (15.2 cm) 79 in. (200.7 cm) 3 in. (7.6 cm) 33 3/4 in. (85.6 cm) 8 in. (20.3 cm) 1 in. (2.5 cm) 27 in. (68.6 cm) 3 in. (7.6 cm) 48 in.2 (310 cm2 ) 24 in.2 (155 cm2) 3 in. (7.
INSTALLATION INSTRUCTIONS 8 Cu. Ft. Electric and Gas Dryers Exhausting requirements WARNING: • Do not exhaust your dryer into a chimney, a wall, a ceiling, an attic, a crawl space, or a concealed space in a building. • Your dryer must be exhausted to the outside to reduce the risk of fire when installed in an alcove or closet. WARNING: NEVER USE A PLASTIC OR NON-METAL FLEXIBLE DUCT • If your existing duct work is plastic, non-metal, or combustible, replace it with metal before installing this dryer.
INSTALLATION INSTRUCTIONS Duct requirements WARNING: You are responsible for correctly installing the exhaust system. • Use a 4-inch (10.2 cm) diameter rigid aluminum or rigid galvanized steel duct. Do not use a smaller duct. • Ducts larger than 4 inches (10.2 cm) in diameter can result in increased accumulation of lint and changes in performance. • Lint should be removed regularly (from the lint filter every cycle ). Removing lint from ducts is recommended at least once each year.
INSTALLATION INSTRUCTIONS 8 Cu. Ft. Electric and Gas Dryers For best results, the static pressure in any exhaust system should be between 0.3 to 0.8 inches of water column, and it cannot be less than 0 under any circumstances with an installed duct with a four-inch diameter. Measurement must be done with the empty dryer working with a manometer at the point where the exhaust duct connects to your dryer. A no-heat setting should be used. The lint filter must be clean. WEATHER HOOD TYPES 4 in. (10.2 cm) .
INSTALLATION INSTRUCTIONS Electrical connections An individual branch (or separate) circuit serving only your dryer is recommended. DO NOT USE AN EXTENSION CORD. Gas models - U.S. and Canada A 120-volt, 60Hz AC approved electrical service, with a 15 ampere fuse or circuit breaker is required. Electric models - U.S. only Your dryer requires a 120/240 volt, 60Hz AC approved electrical service. The electric service requirements can be found on the data label located behind the door.
INSTALLATION INSTRUCTIONS 8 Cu. Ft. Electric and Gas Dryers Using a three-wire outlet If your outlet is a three-wire (three-prong) outlet, choose a three-wire power supply cord with ring or spade terminals and UL listed strain relief. The three-wire power supply cord must: • Be at least 4 ft. (1.2 m) long. • Have three 10-gauge solid copper wires. • Match a three-wire outlet of NEMA Type 10-30R.
INSTALLATION INSTRUCTIONS Gas ignition: Your dryer uses an automatic ignition system to ignite the burner. There is no constant burning pilot. COMMONWEALTH OF MASSACHUSETTS INSTALLATION INSTRUCTIONS Your dryer must be installed by a licensed plumber or gas fitter. A “T” handle manual gas valve must be installed in the gas supply line to the installed dryer at the location of operation. If a flexible gas connector is used to connect your dryer, the connector may not be longer than 3 ft. (91.5 cm).
INSTALLATION INSTRUCTIONS 8 Cu. Ft. Electric and Gas Dryers Changing the dryer vent location (optional) This dryer is shipped to vent from the back. It can also be configured to vent to the bottom or left side. BACK VIEW 3 3/4 in. (9.3 cm) 12 in. (30.5 cm) Tools you will need Adapter kits are standard components and can be purchased from any retailer. Phillips screwdriver Duct tape Gloves Materials you will need 4 in. (10.2 cm) rigid or UL listed flexible duct (not included) 4 in. (10.
INSTALLATION INSTRUCTIONS 1 Remove the two rear exhaust retaining screws, then pull out the exhaust duct. Retaining screw Rear exhaust duct 2 3 Press the tabs on the knockout, then carefully remove the knockout for the desired vent opening. Push the adapter duct onto the blower housing of your dryer. Adapter duct Blower housing DRYER SIDE/BACK VIEW Knockout 4 5 6 Connect a 4 in. (10.2cm) elbow to the 4 in. (10.2cm) duct section, and secure all joints with duct tape.
INSTALLATION INSTRUCTIONS 8 Cu. Ft. Electric and Gas Dryers Bottom venting SIDE VIEW TOP VIEW 4 3/4 in. (12.1 cm) 3 3/4 in. (9.3 cm) 1 1/2 in. (3.8 cm) 12 in. (30.5 cm) 1 Remove the two rear exhaust retaining screws, then pull out the exhaust duct. Retaining screw Rear exhaust duct 2 3 Press the tabs on the knockout, then carefully remove the knockout for the desired vent opening. Push the adapter duct onto the blower housing of your dryer.
INSTALLATION INSTRUCTIONS 5 Insert the elbow/duct assembly through the rear opening and press it onto the adapter duct. Secure in place with duct tape. The male end of the duct should protrude 1.5 in. (3.8 cm) out of your dryer to connect the remaining ductwork. Elbow/Duct assembly 6 Attach duct tape to the back of your dryer to seal the original dryer vent hole. Duct tape Installing your dryer Important: We recommend that you use a qualified installer to install your dryer.
INSTALLATION INSTRUCTIONS 8 Cu. Ft. Electric and Gas Dryers Materials you will need • 3/8" gas dryer gas line (gas model only) • Three- or four-prong (dependent on owner’s house) electric power cord (electric model only) • Exhaust dryer vent kit Before you start Before you start installing your dryer, make sure that: • The location you selected has a grounded electrical outlet. See Grounding requirements on page 20. • You have the correct type of power cord.
INSTALLATION INSTRUCTIONS Step-by-step instructions Note: If a gas dryer is being installed, you will need to call a licensed professional to do the installation. Step 1: Make sure that the floor is a solid, level surface • Use a level to make sure that the floor where you are installing your dryer is level. This helps minimize vibration, noise, and unwanted movement. Notes: • If the front of your dryer is higher than the rear by more than one degree, it may take longer to dry small loads.
INSTALLATION INSTRUCTIONS 2 8 Cu. Ft. Electric and Gas Dryers Connect one end of the exhaust ducting to the venting hole on the back of your dryer, then use aluminum tape to secure the ducting to your dryer. The crimped ends of the duct sections must point away from your dryer. Use a 4 in. (10.2 cm) diameter rigid metal duct. Exhaust ducting 3 Back venting hole Connect the other end of the ducting to the exhaust hood, then tighten the duct strap to secure it in place.
INSTALLATION INSTRUCTIONS 2 Connect the cold water supply hose (not included) from the Y-connector to your washer. Make sure that the hose is snug by hand, then tighten another 2/3 turn with pliers. Cold water supply hose (to washer) 3 Connect the straight end of the short inlet hose to the other outlet on the Y-connector. Make sure that the hose is snug by hand, then tighten another 2/3 turn with pliers.
INSTALLATION INSTRUCTIONS 8 Cu. Ft. Electric and Gas Dryers Step 5: Connect the gas line (for gas models only) Important: Before you connect the gas line, review the gas line requirements in Gas requirements on page 19. 1 Remove the pipe thread protective cap from the gas inlet. Gas inlet on back of dryer 2 3 Apply a pipe joint compound or about 1.5 in. wraps of teflon tape over all threaded connections. The pipe joint compound must be resistant to the actions of any liquefied petroleum gas.
INSTALLATION INSTRUCTIONS 6 Turn on the gas supply. Open WARNING: • All gas installations of the dryer must be equipped with a manual shut-off valve. • Uncoated copper tubing will corrode when subjected to natural gas, causing gas leaks. Use ONLY black iron, stainless steel, or plastic-coated brass piping for the gas supply. • Check all gas connections for leaks using a soap solution. • If bubbles appear, tighten the connections and recheck. DO NOT use an open flame to check for gas leaks.
INSTALLATION INSTRUCTIONS 3 4 5 8 Cu. Ft. Electric and Gas Dryers Connect the other wires to the outer terminal block screws. Be sure to cross the screw through the terminal ring and tighten the screw. Tighten the strain relief screws. Insert the tab of the terminal block cover into your dryer’s rear panel slot, then secure the cover with a screw.
INSTALLATION INSTRUCTIONS 6 Insert the tab of the terminal block cover into your dryer’s rear panel slot, then secure the cover with a screw. WARNING: Electrical Shock Hazard • All U.S. models are produced for a THREE-WIRE SYSTEM CONNECTION. • The dryer frame is grounded to the neutral conductor at the terminal block. A FOUR-WIRE SYSTEM CONNECTION is required for new or remodeled construction, mobile homes, or if local codes do not permit grounding through a neutral conductor.
INSTALLATION INSTRUCTIONS 8 Cu. Ft. Electric and Gas Dryers Step 9: Check the final installation • Before you use your dryer, make sure that: • Your dryer is plugged into an electrical outlet and is properly grounded. • Rigid or semi-rigid metal vent material is installed. Do not use a plastic flexible ducting. • The exhaust duct work is hooked up and the joints are taped. • Your dryer is level and sits firmly on the floor. • Gas models: the gas is turned on with no gas leakage.
INSTALLATION INSTRUCTIONS 4 Reinstall the hinge hole cover on the other side, pressing until it clicks into place. 5 Remove the 14 screws from the back cover, then remove the back cover and door pin. Back cover Door pin 6 34 Remove the eight screws around the door, rotate the door hinge, hinge seat, and door frame 180 degrees, then reinstall the eight screws. www.insigniaproducts.
INSTALLATION INSTRUCTIONS 7 8 Cu. Ft. Electric and Gas Dryers Reassemble the inner door and back cover, place the door pin on the opposite side, then reinstall the 14 screws you removed in step 5. Back cover Door pin 8 Reinstall the door on the front of your dryer, securing with the two screws that you removed in step 2. Screws www.insigniaproducts.
OPERATING INSTRUCTIONS Using your dryer WARNING: To reduce the risk of fire, electric shock, or injury to persons, read the IMPORTANT SAFETY INSTRUCTIONS on page 3 before operating this appliance. Control panel # ITEM DESCRIPTION 1 Cycle selector Press to turn your dryer on or off. If your dryer is on for more than 10 minutes without any buttons being pressed, it automatically turns off. Turn to select the cycle for the type of load. The cycle you select determines the heat control for the cycle.
OPERATING INSTRUCTIONS # 7 8 Cu. Ft. Electric and Gas Dryers ITEM DESCRIPTION Control lock Press and hold the Time Adjust and Time Adjust buttons at the same time for three seconds to turn on the Control Lock function. All buttons except Power will not work when the control lock is activated. Press and hold again for another three seconds to turn off the function. Press to turn your dryer on or off.
OPERATING INSTRUCTIONS Drying a load of clothes Step 1: Turn on your dryer • Press the Power button to turn on your dryer. The display lights up and a sound plays. Step 2: Load your dryer • Place only one wash load in your dryer at a time. • Heavy and light weight fabrics take different amounts of time to dry. If you mix heavy and light weight fabrics in a load, lightweight fabrics may be dry at the end of the cycle while heavy fabrics may still be damp.
OPERATING INSTRUCTIONS 8 Cu. Ft. Electric and Gas Dryers Step 4: Start your dryer 1 Press the Start/Pause button to begin the selected cycle. 2 If you need to pause the cycle (for example to add or remove items or adjust the load), press the Start/Pause button, then open the door. Your dryer stops tumbling. When you are ready to start drying again, close the door, then press the Start/Pause button. Unloading your dryer 1 2 When the drying cycle is over, your dryer beeps and then turns off.
OPERATING INSTRUCTIONS Saving your favorite drying cycle 1 2 3 Set the cycle selector and option functions to your favorite settings. Press and hold the My Cycle button for three seconds to save these settings as your favorite cycle. The light beside the knob flashes to confirm that the settings are saved. To select this saved program, press My Cycle. Your dryer automatically selects your favorite settings, and you can make additional changes if you want.
OPERATING INSTRUCTIONS 8 Cu. Ft. Electric and Gas Dryers Dryer options and settings • Settings in bold or with a filled in (dot) are initial/default settings. A or (dot) shows an available setting. • The Normal, Bulky, Heavy Duty, Active Wear, Sanitize, Towels, Delicates, and Perm Press cycles are sensor cycles. The Quick Dry, Time Dry, Air fluff, and Steam Refresh cycles are manual cycles.
OPERATING INSTRUCTIONS OPTIONAL FUNCTIONS ITEM TYPE TEMP DRYNESS STEAM Time Dry n/a High Medium Med Low Low No Heat n/a n/a • Wrinkle Care • Time Adjust • Electric: 40 min. • Gas: 40 min. • Eco Dry • Time Air Fluff n/a No Heat n/a n/a • Time Adjust • Electric: 20 min. • Time • Gas: 20 min.
OPERATING INSTRUCTIONS 8 Cu. Ft. Electric and Gas Dryers Special laundry tips ITEMS DRYING GUIDE Blankets • Use the Normal cycle and dry only one blanket at a time for best tumbling action. • Make sure that the item is thoroughly dry before using or storing. • During the drying cycle, you may need to reposition the item to make sure that it is completely dried. • Add clean sneakers or tennis balls to the load.
OPERATING INSTRUCTIONS Fabric Care Chart Follow the cleaning and care labels on clothes and other fabrics.
8 Cu. Ft. Electric and Gas Dryers Warning symbols for laundering Dry clean Do not wash Dry clean Do not wring Do not dry clean Do not bleach Line dry/Hang to dry Do not tumble dry Drip dry No steam (added to iron) Dry flat Do not iron Maintaining your dryer Cleaning the exterior • Clean with a soft, damp cloth. Do not use abrasive substances. • Protect the surface from sharp objects. • Do not place any heavy or sharp objects or a detergent box on your dryer.
NS-FDRG80W3/NS-FDRE80W3 Cleaning and inspecting the exhaust system Inspect and clean the exhaust yearly to maintain optimum performance. 1 Disconnect the exhaust duct from your dryer and from the exhaust hood (at the exhaust outlet) outside of the building. 2 Check the interior of the duct and remove any lint. 3 Make sure that lint is removed from the exhaust hood. Lint may collect in the exhaust hood so that the flappers or louvers will not open or close completely.
USER MAINTENANCE INSTRUCTIONS 8 Cu. Ft. Electric and Gas Dryers Troubleshooting CAUTION: Do not try to repair your dryer yourself. Doing so invalidates the warranty. Check this table for solutions to common questions or problems. If your issue is not listed here, contact customer service at 1-877-467-4289 (U.S. and Canada). PROBLEM SOLUTION My dryer does • Make sure that the dryer door is closed completely. • If you opened the door during the drying cycle, press the not start. Start/Pause button again.
USER MAINTENANCE INSTRUCTIONS PROBLEM SOLUTION My dryer has an odd odor. • Your dryer draws air from the surrounding room air. Household odors from paint, varnish, strong cleaners, and so forth, may enter your dryer with the surrounding room air. This is normal. When these odors linger in the air, ventilate the room completely before using your dryer. My clothing is still wrinkled • If the dryer load is too large, items cannot tumble freely. Try loading fewer items.
USER MAINTENANCE INSTRUCTIONS 8 Cu. Ft. Electric and Gas Dryers Understanding the error codes Your dryer is equipped with an automatic error-monitoring system to detect and diagnose problems at an early stage. When an error occurs, your dryer beeps for five seconds every 15 minutes. ERROR CODE POSSIBLE CAUSE SOLUTIONS C9 The PCB failed. Call customer service for help. Do not use your dryer. E4 The humidity sensor failed.
NS-FDRG80W3/NS-FDRE80W3 ONE-YEAR LIMITED WARRANTY Definitions: The Distributor* of Insignia branded products warrants to you, the original purchaser of this new Insignia-branded product (“Product”), that the Product shall be free of defects in the original manufacturer of the material or workmanship for a period of one (1) year from the date of your purchase of the Product (“Warranty Period”).
8 Cu. Ft. Electric and Gas Dryers • • • • • • • • Damage due to incorrect operation or maintenance Connection to an incorrect voltage or power supply Attempted repair by any person not authorized by Insignia to service the Product Products sold “as is” or “with all faults” Consumables, including but not limited to batteries (i.e. AA, AAA, C etc.
www.insigniaproducts.com 1-877-467-4289 (U.S. and Canada) INSIGNIA is a trademark of Best Buy and its affiliated companies. Distributed by Best Buy Purchasing, LLC 7601 Penn Ave South, Richfield, MN 55423 U.S.A. ©2023 Best Buy. All rights reserved.
