Installation Guide

ManualsBrandsCreative ManualsComputer AccessoriesLabs Sound Blaster Audigy Rx

Guide to 7.1 Output with Sound Blaster Audigy Rx and

Sound Blaster Audigy 5

How to connect the Sound Blaster Audigy Rx / Audigy 5 to 7.1 Speaker

System – Sound Blaster’s Proprietary Connectors

The diagram below illustrates the signal (pin-out) of the 7.1 connectors on Sound Blaster Audigy Rx /

Audigy 5. While the 7.1 configuration for the Sound Blaster Audigy Rx / Audigy 5 is proprietary, there

are other ways to achieve 7.1 output. These cables are widely available online and in most major

electronics stores.

7.1 Channel Analog Audio

Description

Line-out 1 Jack (Front Left / Right)

Rear Right

Line-out 2 Jack (Rear Left / Right / Side

Right)

Ground

Line-out 3 Jack (Center / Sub / Side Left)

Side Right

Front Left

Center

Front Right

Subwoofer

Ground

Rear Left

Side Left

Summary of content (5 pages)

PAGE 1
Guide to 7.1 Output with Sound Blaster Audigy Rx and Sound Blaster Audigy 5 How to connect the Sound Blaster Audigy Rx / Audigy 5 to 7.1 Speaker System – Sound Blaster’s Proprietary Connectors The diagram below illustrates the signal (pin-out) of the 7.1 connectors on Sound Blaster Audigy Rx / Audigy 5. While the 7.1 configuration for the Sound Blaster Audigy Rx / Audigy 5 is proprietary, there are other ways to achieve 7.1 output.
PAGE 2
How to connect the Sound Blaster Audigy Rx / Audigy 5 to 7.1 Speaker System – Female RCA Connectors The diagram below illustrates the cables required (purchased separately) to connect 7.1 speaker systems with female RCA connectors to the Sound Blaster Audigy Rx / Audigy 5. Sound Blaster Audigy Rx / Audigy 5 (A) 3.5 mm jack to Male RCA audio cable 7.1 Speaker System with Female RCA Connectors (B) 3.5 mm jack to Male RCA AV cable Cables required (purchased separately) (A) 1 set of 3.
PAGE 3
How to connect the Sound Blaster Audigy Rx / Audigy 5 to 7.1 Speaker System – Male RCA Connectors The diagram below illustrates the cables required (purchased separately) to connect 7.1 speaker systems with male RCA connectors to the Sound Blaster Audigy Rx / Audigy 5. Sound Blaster Audigy Rx / Audigy 5 (A) 3.5 mm jack to Female RCA audio cable 7.1 Speaker System with Male RCA Connectors (B) 3.5 mm jack to Female RCA AV cable Cables required (purchased separately) (A) 1 set of 3.
PAGE 4
How to connect the Sound Blaster Audigy Rx / Audigy 5 to 7.1 Speaker System – Male 3.5 mm Connectors The diagram below illustrates the cables required (purchased separately) to connect 7.1 speaker systems with male 3.5 mm connectors to the Sound Blaster Audigy Rx / Audigy 5. Sound Blaster Audigy Rx / Audigy 5 (A) 3.5 mm jack to Female RCA AV cable 7.1 Speaker System with 3.5 mm Male Connectors (B) Female 3.5 mm jack to Male RCA audio cable Cables required (purchased separately) (A) 2 sets of 3.
PAGE 5
How to connect the Sound Blaster Audigy Rx / Audigy 5 to 7.1 Speaker System – Female 3.5 mm Connectors The diagram below illustrates the cables required (purchased separately) to connect 7.1 speaker systems with female 3.5 mm connectors to the Sound Blaster Audigy Rx / Audigy 5. Sound Blaster Audigy Rx / Audigy 5 7.1 Speaker System with 3.5 mm Female Connectors (A) Connect 3.5 mm Stereo cable to Line-out 1 and 7.1 Speaker System’s female 3.5 mm connector (B) 3.