PK5001Z 802.11n Wireless ADSL2+ 4-port Gateway Quick Start Guide Version 3.
PK5001Z Quick Start Guide Overview The PK5001Z i s a wireless ADSL router with a four-port built-i n switch. This Quick Start Guide shows you how to use the PK5001Z to connect to the Internet and how to configure the device settings to connect wirelessly y. See your User’s Guide for background information on all features. Quick Login Information LAN IP address http://192.168.0.
PK5001Z Quick Start Guide Hardware Connections 1 DSL: Use the gray telephone wire to connect your PK5001Z’s DSL port to a telephone jack (or to the modem port on a splitter if you are using one). 2 ETHERNET: Use the yellow Ethernet cable to connect a computer to an ETHERNET port for initial configuration and/or Internet access. 3 POWER: Use the included power adaptor to connect an appropriate power source to the POWER socket. Make sure the power source is on. 4 Push in the POWER button.
PK5001Z Quick Start Guide vendor. 2 Internet Connection Setup: Automatic Use this section to have your PK5001Z automatically detect and set up your Internet connection. 1 Open your web browser to a website. Wait while your PK5001Z tries to detect your DSL connection to your ISP. This may take a few minutes. 2 After it detects the connection, the DSL light shows green on your device and the Internet light comes on when the Internet is ready for you to use.
PK5001Z Quick Start Guide settings. If you do not set wireless security then anyone within range could use your PK5001Z to access your network and the Internet. Choose W PA-PSK wireless security if your wireless device supports it as it is stronger than W EP. Otherwise choose W EP. 1 Select Active and click Next to continue. It i s strongly recommended that Enable OTIST i s NOT selected. See section 7 for more information. 2 C o n f i g u r e your wireless settings i n the screen. Click Next.
PK5001Z Quick Start Guide see the ISP Parameters for Internet Access screen when you run the wizard (see section 4, step 4). 1 Login again. (Follow steps 1 to 5 in section 3.) 2 Select Go to Advanced setup. Then, click Apply. 3 The Status screen appears. Click Network > WAN i n the navigation panel on the left of the screen. 4 E n t e r the information exactly as provided by your ISP. Click Apply.
PK5001Z Quick Start Guide 2 If you cannot access the Internet when your computer i s connected to the ETHERNET port, follow these steps. A) Check the lights on the front panel . If they are different from what i s described in section 1, make sure the PK5001Z is correctly connected. (See section 1.) If the lights are still different, turn off the device, wait a few seconds, and turn it on again. B) Check you have correctly entered the information your ISP gave you.
PK5001Z Quick Start Guide Provider. 3 If you cannot access the Internet using the wireless network, follow these steps. A) On a computer i n the wireless network, open your browser, and go to http://192.168.0.1. If you see the login screen i n section 3, follow suggestions A - F above. If you do not, go to the next step. B) On a computer connected to the PK5001Z, make sure your PK5001Z and the computers on your wireless network are using the sam e wireless and wireless security settings.
PK5001Z Quick Start Guide information will be included i n the final version of the manual. Customer Information 1 This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On bottom of this equipment i s a label that contains, among other information, a product identifier of QW EST PK5001Z. If requested, this number must be provided to the telephone company.
PK5001Z Quick Start Guide section); otherwise do not alternate or repair any parts of device except specified. 6 Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission or corporation commission for information.
PK5001Z Quick Start Guide The device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: . This device may not cause harmful interference. . This device must accept any interference received, including interference that may cause undesired operations. This device has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules.
PK5001Z Quick Start Guide 4 Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement . This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. . IEEE 802.11b or 802.11g or 802.11n (20MHz) operation of this product in the U.S.A. is firmware-limited to channels 1 through 11. IEEE 802.11n (40MHz) operation of this product in the U.S.A. is firmware-limited to channels 3 through 9. .
PK5001Z Quick Start Guide . Do NOT install, use, or service this device during a thunderstorm. There is a remote risk of electric shock from lightning. . Connect ONLY suitable accessories to the device. . Do NOT open the device or unit. Opening or removing covers can expose you to dangerous high voltage points or other risks. ONLY qualified service personnel should service or disassemble this device. Please contact your vendor for further information. . Make sure to connect the cables to the correct ports.
PK5001Z Quick Start Guide . Do NOT attempt to repair the power adaptor or cord. Contact your local vendor to Order a new one. . Do not use the device outside, and make sure all the connections are indoors. There is a remote risk of electric shock from lightning. . Do NOT obstruct the device ventilation slots, as insufficient airflow may harm your device. . Use only No. 26 AWG (American Wire Gauge) or larger telecommunication line cord. .
PK5001Z Quick Start Guide The user’s manual or instruction manual for an intentional or unintentional radiator shall caution the user that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.