P-660RU-Tx v2 ADSL2+ Ethernet / USB Router Quick Start Guide Version 3.
P-660RU-Tx v2 Quick Start Guide Overview The P-660RU-Tx v2 is an ADSL router with both USB and Ethernet ports. See your User’s Guide for background information on all features. This Quick Start Guide shows you how to: • Connect the hardware. • Set up your Internet connection. The device should connect to the Internet automatically if it is preconfigured.
P-660RU-Tx v2 Quick Start Guide 1 Hardware Connections There are two ways to connect your computer or computer network to the P-660RU-Tx v2: Option A: Connect via Ethernet. See page 2. Option B: Connect via USB (you will need to install the USB driver). See page 4. Option A: Connect via Ethernet 1 ETHERNET: Use the yellow Ethernet cable to connect a computer to the ETHERNET port for initial configuration and/or Internet access.
P-660RU-Tx v2 Quick Start Guide 2 DSL: Use the gray telephone wire to connect your P660RU-Tx v2’s DSL port to a telephone jack (or to a splitter, if one is already installed). 3 POWER: Use the power adaptor provided with your P660RU-Tx v2 to connect an appropriate power source to the POWER socket. Make sure the power source is on. 4 Push in the POWER button. 5 Look at the lights on the front panel. • The POWER light blinks while your P-660RU-Tx v2 starts up and stays on once it is ready.
P-660RU-Tx v2 Quick Start Guide V If any of these lights are not on, check your connections and inspect your cables for damage. If the lights are still off, contact your local vendor.
P-660RU-Tx v2 Quick Start Guide " Do NOT connect the same computer to both the USB and ETHERNET ports on the P-660RU-Tx v2. 1 USB: Connect the provided USB cable to the P-660RU-Tx v2’s USB port. 2 DSL: Use the gray telephone wire to connect your P660RU-Tx v2’s DSL port to a telephone jack (or to a splitter, if one is already installed). 3 POWER: Use the power adaptor provided with your P660RU-Tx v2 to connect an appropriate power source to the POWER socket. Make sure the power source is on.
P-660RU-Tx v2 Quick Start Guide V If any of these lights are not on, check your connections and inspect your cables for damage. If the lights are still off, contact your local vendor. Install the USB Software If you want to connect to the Internet through the P-660RU-Tx v2's USB port, install the USB driver before you connect the P-660RU-Tx v2 to the USB port. Follow the steps for your operating system to install the USB driver.
P-660RU-Tx v2 Quick Start Guide 5 An install warning may appear in the Windows Vista OS. Click Allow to continue. 6 Click Next in the Welcome screen to begin the USB Installation Wizard. Follow the installation prompts. You may need to restart your computer at the end of the installation.
P-660RU-Tx v2 Quick Start Guide Macintosh Computer System Requirements • Macintosh operating system versions 10.1, 10.2 and 10.3. • An available USB port Procedures 1 Save your work and close all applications. 2 Insert the included CD. A CD’s icon automatically displays on the desktop. 3 Double-click the CD's icon. 4 Double-click the MAC version of your computer.
P-660RU-Tx v2 Quick Start Guide 5 Double-click one of the following. If you selected MAC10.1, double click the P-660RU-T icon. If you selected MAC 10.2_10.3, double click the P-660RUTx.dmg icon.
P-660RU-Tx v2 Quick Start Guide 6 Click Continue in the Welcome screen to begin the USB installation. Follow the installation prompts. You may need to restart your computer at the end of the installation. 2 Connection Setup: Automatic Use this section to have your P-660RU-Tx v2 automatically detect and set up your Internet connection. 1 Open your web browser, and go to any web page (for example, http://www.zyxel.com). Your P-660RU-Tx v2 tries to detect your Internet connection.
P-660RU-Tx v2 Quick Start Guide connection test screen similar to the following, go to step 5. 3 If the connection test is successful, the following screen appears. Your Internet connection is ready for you to use. 4 If the connection test is not successful, you may see a screen similar to the following. Follow the instructions in the screen.
P-660RU-Tx v2 Quick Start Guide 5 If the connection test is not successful, check your connections and restart the P-660RU-Tx v2. If you still cannot access the Internet, take the steps in the following section. You should have information provided by your Internet Service Provider. 3 Connection Setup: Wizard Use this section to set up your Internet connection if automatic Internet connection does not work (see section 2). You should have information from your Internet Service Provider (ISP).
P-660RU-Tx v2 Quick Start Guide 3 Type (and retype) a new password and click Apply. " You have to use a new password other than the default password 1234, or you cannot apply it successfully. 4 The system asks you to enter your new password to log in again.
P-660RU-Tx v2 Quick Start Guide 5 Select Go to Wizard setup. Click Apply. 6 Click INTERNET SETUP. Wait while your P-660RU-Tx v2 tries to detect your DSL connection.
P-660RU-Tx v2 Quick Start Guide 7 If the connection test is successful, the following screen displays. Click Finish to exit the wizard. 8 If the connection test is not successful, you may see a screen similar to one of the following.
P-660RU-Tx v2 Quick Start Guide Either click Restart the Internet Setup Wizard (if available) to have the ZyXEL Device detect your connection again, or click Next to set up your Internet connection manually. 9 Follow the instructions in the wizard. Enter your Internet connection information exactly as provided by your ISP. If you do not see the following screen, go to section 4.
P-660RU-Tx v2 Quick Start Guide 1 Follow steps 1 to 3 in section 3 in order to log in to the web configurator. 2 Select Go to Advanced setup. Click Apply. 3 The Status screen appears. Click Network > WAN in the navigation panel on the left of the screen. 4 The Internet Connection screen appears. Enter the information exactly as provided by your ISP and click Apply.
P-660RU-Tx v2 Quick Start Guide " The fields available in this screen depend on the Mode you select. 5 If you still cannot access the Internet, see Troubleshooting and/or contact your Internet Service Provider (ISP) for assistance.
P-660RU-Tx v2 Quick Start Guide Troubleshooting 1 If you want to verify your USB installation, • Check the status of the P-660RU-Tx v2 in the Device Manager window. Click Start > Settings > Control Panel > System > Hardware and then click Device Manager. (Steps may vary depending on the version of Windows.) • Verify the status of the P-660RU-Tx v2 under Network Adapter. Check that there is no question mark on the device icon for the P-660RU-Tx v2.
P-660RU-Tx v2 Quick Start Guide B) If your ISP gave you Internet connection information, ensure you enter it correctly. For example, if your account has a user name and password, make sure you type it correctly. In addition, if you are not sure which encapsulation your ISP uses, contact your ISP. If your ISP did not give you Internet connection information, follow the steps in section 2. C) If you are using a new Internet account, contact your ISP to make sure it is active.
P-660RU-Tx v2 Quick Start Guide • Click the wizard icon ( ). Run the Internet Setup wizard again. Check whether you can access the Internet. If you still cannot access the Internet, take the following steps: • If you are using Bridge mode (check Mode in the Network > WAN > Internet Connection screen) click NAT > General and ensure Active Network Address Translation (NAT) is not selected. Click LAN > DHCP Setup and ensure that DHCP is set to None. Your ISP gives your computer an IP address directly.