Prestige 660RU-Tx Series ADSL2+ Ethernet/USB Gateway User’s Guide Version 3.
Prestige 660RU-Tx Series User’s Guide Copyright Copyright © 2005 by ZyXEL Communications Corporation. The contents of this publication may not be reproduced in any part or as a whole, transcribed, stored in a retrieval system, translated into any language, or transmitted in any form or by any means, electronic, mechanical, magnetic, optical, chemical, photocopying, manual, or otherwise, without the prior written permission of ZyXEL Communications Corporation. Published by ZyXEL Communications Corporation.
Prestige 660RU-Tx Series User’s Guide Federal Communications Commission (FCC) Interference Statement This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired operations. This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules.
Prestige 660RU-Tx Series User’s Guide ZyXEL Limited Warranty ZyXEL warrants to the original end user (purchaser) that this product is free from any defects in materials or workmanship for a period of up to two years from the date of purchase.
Prestige 660RU-Tx Series User’s Guide Customer Support Please have the following information ready when you contact customer support. • • • • Product model and serial number. Warranty Information. Date that you received your device. Brief description of the problem and the steps you took to solve it. METHOD SUPPORT E-MAIL TELEPHONEA WEB SITE LOCATION SALES E-MAIL FAX FTP SITE support@zyxel.com.tw +886-3-578-3942 WORLDWIDE NORTH AMERICA GERMANY DENMARK NORWAY SWEDEN FINLAND www.zyxel.
Prestige 660RU-Tx Series User’s Guide Table of Contents Copyright .................................................................................................................. 2 Federal Communications Commission (FCC) Interference Statement ............... 3 ZyXEL Limited Warranty.......................................................................................... 4 Customer Support....................................................................................................
Prestige 660RU-Tx Series User’s Guide 3.1.1 Encapsulation ...........................................................................................42 3.1.1.1 ENET ENCAP .................................................................................42 3.1.1.2 PPP over Ethernet ..........................................................................42 3.1.1.3 PPPoA .............................................................................................42 3.1.1.4 RFC 1483 ...........................
Prestige 660RU-Tx Series User’s Guide 5.6 Configuring LAN .................................................................................................61 Chapter 6 WAN Setup.............................................................................................................. 64 6.1 WAN Overview ...................................................................................................64 6.2 Metric ..........................................................................................
Prestige 660RU-Tx Series User’s Guide Chapter 10 Remote Management Configuration .................................................................... 90 10.1 Remote Management Overview .......................................................................90 10.1.1 Remote Management Limitations ...........................................................90 10.1.2 Remote Management and NAT ..............................................................91 10.1.3 System Timeout .................................
Prestige 660RU-Tx Series User’s Guide Chapter 14 Menu 1 General Setup ......................................................................................... 124 14.1 General Setup ................................................................................................124 14.2 Procedure To Configure Menu 1 ....................................................................124 14.2.1 Procedure to Configure Dynamic DNS .................................................
Prestige 660RU-Tx Series User’s Guide 18.5 Editing ATM Layer Options ............................................................................151 18.5.1 VC-based Multiplexing (non-PPP Encapsulation) ................................151 18.5.2 LLC-based Multiplexing or PPP Encapsulation ....................................152 18.5.3 Advance Setup Options ........................................................................152 Chapter 19 Static Route Setup ...............................................
Prestige 660RU-Tx Series User’s Guide 22.6 Example Filter ................................................................................................187 22.7 Applying Filters and Factory Defaults ............................................................190 22.7.1 Ethernet Traffic .....................................................................................190 22.7.2 Remote Node Filters .............................................................................
Prestige 660RU-Tx Series User’s Guide 25.4.4 FTP Session Example of Firmware File Upload ...................................215 25.4.5 TFTP File Upload ..................................................................................215 25.4.6 TFTP Upload Command Example ........................................................216 Chapter 26 System Maintenance............................................................................................ 218 26.1 Command Interpreter Mode ......................
Prestige 660RU-Tx Series User’s Guide 30.7 Problems with the Password ..........................................................................244 30.8 Problems with the Web Configurator .............................................................245 30.9 Problems with Remote Management .............................................................245 Appendix A Splitters and Microfilters ..................................................................................... 246 Connecting a POTS Splitter .
Prestige 660RU-Tx Series User’s Guide Appendix E Virtual Circuit Topology ...................................................................................... 270 ............................................................................................................................... 270 Appendix F Command Interpreter........................................................................................... 272 Command Syntax..........................................................................
Prestige 660RU-Tx Series User’s Guide List of Figures Figure 1 Prestige Internet Access Application .................................................................... 35 Figure 2 Prestige LAN-to-LAN Application .......................................................................... 36 Figure 3 Password Screen .................................................................................................. 38 Figure 4 Change Password at Login ..........................................................
Prestige 660RU-Tx Series User’s Guide Figure 37 Network Connections .......................................................................................... 97 Figure 38 Windows Optional Networking Components Wizard .......................................... 98 Figure 39 Networking Services ........................................................................................... 99 Figure 40 Network Connections ..........................................................................................
Prestige 660RU-Tx Series User’s Guide Figure 80 Menu 21 Filer Set Configuration ......................................................................... 150 Figure 81 Menu 21.11 WebSet 11 ....................................................................................... 150 Figure 82 Menu 21.12 WebSet 12 ...................................................................................... 151 Figure 83 Menu 11.6 for VC-based Multiplexing ...............................................................
Prestige 660RU-Tx Series User’s Guide Figure 123 Menu 21.5.1 Generic Filter Rule ...................................................................... 186 Figure 124 Protocol and Device Filter Sets ......................................................................... 187 Figure 125 Sample Telnet Filter .......................................................................................... 188 Figure 126 Menu 21.6.1 Sample Filter .......................................................................
Prestige 660RU-Tx Series User’s Guide Figure 166 Menu 26.1 Schedule Set Setup ....................................................................... 239 Figure 167 Applying Schedule Set(s) to a Remote Node (PPPoE) .................................... 240 Figure 168 Connecting a POTS Splitter .............................................................................. 246 Figure 169 Connecting a Microfilter ....................................................................................
Prestige 660RU-Tx Series User’s Guide 21
Prestige 660RU-Tx Series User’s Guide List of Tables Table 1 ADSL Standards .................................................................................................... 30 Table 2 Front Panel LED Description ................................................................................. 36 Table 3 Web Configurator Screens Summary .................................................................... 40 Table 4 Internet Access Wizard Setup: First Screen .............................................
Prestige 660RU-Tx Series User’s Guide Table 37 Menu 2 WAN Backup Setup ................................................................................ 129 Table 38 Menu 2.1Traffic Redirect Setup ........................................................................... 130 Table 39 DHCP Ethernet Setup ......................................................................................... 134 Table 40 TCP/IP Ethernet Setup ..................................................................................
Prestige 660RU-Tx Series User’s Guide Table 80 Troubleshooting the Password ............................................................................ 244 Table 81 Troubleshooting the Web Configurator ................................................................ 245 Table 82 Troubleshooting Remote Management ............................................................... 245 Table 83 Classes of IP Addresses .....................................................................................
Prestige 660RU-Tx Series User’s Guide 25
Prestige 660RU-Tx Series User’s Guide Preface Congratulations on your purchase of the Prestige 660RU-Tx ADSL2+ Ethernet/USB Gateway. Note: Register your product online to receive e-mail notices of firmware upgrades and information at www.zyxel.com for global products, or at www.us.zyxel.com for North American products. Your Prestige is easy to install and configure. About This User's Guide This manual is designed to guide you through the configuration of your Prestige for its various applications.
Prestige 660RU-Tx Series User’s Guide The Quick Start Guide is designed to help you get up and running right away. They contain connection information and instructions on getting started. • Web Configurator Online Help Embedded web help for descriptions of individual screens and supplementary information. • ZyXEL Glossary and Web Site Please refer to www.zyxel.com for an online glossary of networking terms and additional support documentation. User Guide Feedback Help us help you.
Prestige 660RU-Tx Series User’s Guide Introduction to DSL DSL (Digital Subscriber Line) technology enhances the data capacity of the existing twistedpair wire that runs between the local telephone company switching offices and most homes and offices.
Prestige 660RU-Tx Series User’s Guide 29 Introduction to DSL
Prestige 660RU-Tx Series User’s Guide CHAPTER 1 Getting To Know Your Prestige This chapter describes the key features and applications of your Prestige. 1.1 Introducing the Prestige Your Prestige integrates high-speed 10/100Mbps auto-negotiating LAN interface(s) and a high-speed ADSL port into a single package. The Prestige is ideal for high-speed Internet browsing and making LAN-to-LAN connections to remote networks. The Prestige is an ADSL router compatible with the ADSL/ADSL2/ADSL2+ standards.
Prestige 660RU-Tx Series User’s Guide 1.1.1 Features of the Prestige The following sections describe the features of the Prestige. High Speed Internet Access Your Prestige ADSL/ADSL2/ADSL2+ router can support downstream transmission rates of up to 24Mbps and upstream transmission rates of 3.5Mbps. Actual speeds attained depend on ISP DSLAM environment.
Prestige 660RU-Tx Series User’s Guide PPPoE Support (RFC2516) PPPoE (Point-to-Point Protocol over Ethernet) emulates a dial-up connection. It allows your ISP to use their existing network configuration with newer broadband technologies such as ADSL. The PPPoE driver on the Prestige is transparent to the computers on the LAN, which see only Ethernet and are not aware of PPPoE thus saving you from having to manage PPPoE clients on individual computers.
Prestige 660RU-Tx Series User’s Guide • • • • • PPP over AAL5 (RFC 2364). PPP over Ethernet over AAL5 (RFC 2516). RFC 1661. PPP over PAP (RFC 1334). PPP over CHAP (RFC 1994). Protocol Support • DHCP Support DHCP (Dynamic Host Configuration Protocol) allows the individual clients (computers) to obtain the TCP/IP configuration at start-up from a centralized DHCP server. The Prestige has built-in DHCP server capability enabled by default.
Prestige 660RU-Tx Series User’s Guide Encapsulation The Prestige supports PPPoA (RFC 2364 - PPP over ATM Adaptation Layer 5), RFC 1483 encapsulation over ATM, MAC encapsulated routing (ENET encapsulation) as well as PPP over Ethernet (RFC 2516).
Prestige 660RU-Tx Series User’s Guide Housing Your Prestige's compact and ventilated housing minimizes space requirements making it easy to position anywhere in your busy office. 1.1.2 Applications for the Prestige Here are some example uses for which the Prestige is well suited. 1.1.2.1 Internet Access The Prestige is the ideal high-speed Internet access solution. Your Prestige supports the TCP/ IP protocol, which the Internet uses exclusively.
Prestige 660RU-Tx Series User’s Guide Figure 2 Prestige LAN-to-LAN Application 1.1.3 Prestige Hardware Installation and Connection Refer to the Quick Start Guide for information on hardware installation and connection. 1.1.4 Front Panel LEDs The following table describes the LEDs on the front panel. Table 2 Front Panel LED Description LED COLOR STATUS DESCRIPTION PWR/SYS Green On The Prestige is receiving power and functioning properly. Blinking The Prestige is rebooting.
Prestige 660RU-Tx Series User’s Guide 37 Chapter 1 Getting To Know Your Prestige
Prestige 660RU-Tx Series User’s Guide CHAPTER 2 Introducing the Web Configurator This chapter describes how to access and navigate the web configurator. 2.1 Web Configurator Overview The web configurator is an HTML-based management interface that allows easy Prestige setup and management via Internet browser. Use Internet Explorer 6.0 and later or Netscape Navigator 7.0 and later versions with JavaScript enabled. Recommended screen resolution is 1024 by 768 pixels. 2.1.
Prestige 660RU-Tx Series User’s Guide 6 It is highly recommended you change the default password! Enter a new password, retype it to confirm and click Apply; alternatively click Ignore to proceed to the main menu if you do not want to change the password now. Note: If you do not change the password, the following screen appears every time you log in. Figure 4 Change Password at Login 7 You should now see the SITE MAP screen. Note: The Prestige automatically times out after five minutes of inactivity.
Prestige 660RU-Tx Series User’s Guide • Click Wizard Setup to begin a series of screens to configure your Prestige for the first time. • Click a link under Advanced Setup to configure advanced Prestige features. • Click a link under Maintenance to see Prestige performance statistics, upload firmware and back up, restore or upload a configuration file. • Click Site Map to go to the Site Map screen. • Click Logout in the navigation panel when you have finished a Prestige management session.
Prestige 660RU-Tx Series User’s Guide Table 3 Web Configurator Screens Summary (continued) LINK SUB-LINK FUNCTION Remote Management Use this screen to configure through which interface(s) and from which IP address(es) users can use Telnet/FTP/Web to manage the Prestige. UPnP Use this screen to enable UPnP on the Prestige. Maintenance System Status This screen contains administrative and system-related information.
Prestige 660RU-Tx Series User’s Guide CHAPTER 3 Wizard Setup This chapter provides information on the Wizard Setup screens for Internet access in the web configurator. 3.1 Introduction Use the Wizard Setup screens to configure your system for Internet access with the information (provided by your ISP) that you fill in the Internet Account Information table of the Quick Start Guide. Your ISP may have already configured some of the fields in the wizard screens for you. 3.1.
Prestige 660RU-Tx Series User’s Guide 3.1.1.4 RFC 1483 RFC 1483 describes two methods for Multiprotocol Encapsulation over ATM Adaptation Layer 5 (AAL5). The first method allows multiplexing of multiple protocols over a single ATM virtual circuit (LLC-based multiplexing) and the second method assumes that each protocol is carried over a separate ATM virtual circuit (VC-based multiplexing). Please refer to the RFC for more detailed information. 3.1.
Prestige 660RU-Tx Series User’s Guide Figure 6 Internet Access Wizard Setup: First Screen The following table describes the labels in this screen. Table 4 Internet Access Wizard Setup: First Screen LABEL DESCRIPTION Mode From the Mode drop-down list box, select Routing (default) if your ISP allows multiple computers to share an Internet account. Otherwise select Bridge. Encapsulation Select the encapsulation type your ISP uses from the Encapsulation drop-down list box.
Prestige 660RU-Tx Series User’s Guide If the ISP did not explicitly give you an IP network number, then most likely you have a single user account and the ISP will assign you a dynamic IP address when the connection is established. If this is the case, it is recommended that you select a network number from 192.168.0.0 to 192.168.255.0 and you must enable the Network Address Translation (NAT) feature of the Prestige.
Prestige 660RU-Tx Series User’s Guide 3.2.1.4 Private IP Addresses Every machine on the Internet must have a unique address. If your networks are isolated from the Internet, for example, only between your two branch offices, you can assign any IP addresses to the hosts without problems. However, the Internet Assigned Numbers Authority (IANA) has reserved the following three blocks of IP addresses specifically for private networks: • 10.0.0.0 — 10.255.255.255 • 172.16.0.0 — 172.31.255.255 • 192.168.0.
Prestige 660RU-Tx Series User’s Guide Figure 7 Internet Connection with PPPoE The following table describes the labels in this screen. Table 5 47 Internet Connection with PPPoE LABEL DESCRIPTION Service Name Type the name of your PPPoE service here. User Name Enter the user name exactly as your ISP assigned. If assigned a name in the form user@domain where domain identifies a service name, then enter both components exactly as given.
Prestige 660RU-Tx Series User’s Guide Figure 8 Internet Connection with RFC 1483 The following table describes the labels in this screen. Table 6 Internet Connection with RFC 1483 LABEL DESCRIPTION IP Address This field is available if you select Routing in the Mode field. Type your ISP assigned IP address in this field. Network Address Translation Select None, SUA Only or Full Feature from the drop-down list box. Refer to Chapter 7, on page 74 for more details.
Prestige 660RU-Tx Series User’s Guide The following table describes the labels in this screen. Table 7 Internet Connection with ENET ENCAP LABEL DESCRIPTION IP Address A static IP address is a fixed IP that your ISP gives you. A dynamic IP address is not fixed; the ISP assigns you a different one each time you connect to the Internet. .
Prestige 660RU-Tx Series User’s Guide The following table describes the labels in this screen. Table 8 Internet Connection with PPPoA LABEL DESCRIPTION User Name Enter the login name that your ISP gives you. Password Enter the password associated with the user name above. IP Address This option is available if you select Routing in the Mode field. A static IP address is a fixed IP that your ISP gives you.
Prestige 660RU-Tx Series User’s Guide Figure 11 Internet Access Wizard Setup: Third Screen If you want to change your Prestige LAN settings, click Change LAN Configuration to display the screen as shown next.
Prestige 660RU-Tx Series User’s Guide Figure 12 Internet Access Wizard Setup: LAN Configuration The following table describes the labels in this screen. Table 9 Internet Access Wizard Setup: LAN Configuration LABEL DESCRIPTION LAN IP Address Enter the IP address of your Prestige in dotted decimal notation, for example, 192.168.1.1 (factory default). Note: If you changed the Prestige's LAN IP address, you must use the new IP address if you want to access the web configurator again.
Prestige 660RU-Tx Series User’s Guide 3.2.7 Internet Access Wizard Setup: Connection Test The Prestige automatically tests the connection to the computer(s) connected to the LAN ports. To test the connection from the Prestige to the ISP, click Start Diagnose. Otherwise click Return to Main Menu to go back to the Site Map screen. Figure 13 Internet Access Wizard Setup: Connection Tests 3.2.7.1 Test Your Internet Connection Launch your web browser and navigate to www.zyxel.com.
Prestige 660RU-Tx Series User’s Guide CHAPTER 4 Password Setup This chapter provides information on the Password screen. 4.1 Password Overview It is highly recommended that you change the password for accessing the Prestige. 4.1.1 Configuring Password To change your Prestige’s password (recommended), click Password in the Site Map screen. The screen appears as shown. Figure 14 Password The following table describes the fields in this screen.
Prestige 660RU-Tx Series User’s Guide 55 Chapter 4 Password Setup
Prestige 660RU-Tx Series User’s Guide CHAPTER 5 LAN Setup This chapter describes how to configure LAN settings. 5.1 LAN Overview A Local Area Network (LAN) is a shared communication system to which many computers are attached. A LAN is a computer network limited to the immediate area, usually the same building or floor of a building. The LAN screens can help you configure a LAN DHCP server and manage IP addresses. 5.1.
Prestige 660RU-Tx Series User’s Guide 5.2 DNS Server Address DNS (Domain Name System) is for mapping a domain name to its corresponding IP address and vice versa. The DNS server is extremely important because without it, you must know the IP address of a machine before you can access it. The DNS server addresses that you enter in the DHCP setup are passed to the client machines along with the assigned IP address and subnet mask. There are two ways that an ISP disseminates the DNS server addresses.
Prestige 660RU-Tx Series User’s Guide 5.4 LAN TCP/IP The Prestige has built-in DHCP server capability that assigns IP addresses and DNS servers to systems that support DHCP client capability. 5.4.1 Factory LAN Defaults The LAN parameters of the Prestige are preset in the factory with the following values: • IP address of 192.168.1.1 with subnet mask of 255.255.255.0 (24 bits) • DHCP server enabled with 32 client IP addresses starting from 192.168.1.33.
Prestige 660RU-Tx Series User’s Guide 5.4.4 Multicast Traditionally, IP packets are transmitted in one of either two ways - Unicast (1 sender - 1 recipient) or Broadcast (1 sender - everybody on the network). Multicast delivers IP packets to a group of hosts on the network - not everybody and not just 1. IGMP (Internet Group Multicast Protocol) is a network-layer protocol used to establish membership in a Multicast group - it is not used to carry user data.
Prestige 660RU-Tx Series User’s Guide Figure 16 Any IP Example The Any IP feature does not apply to a computer using either a dynamic IP address or a static IP address that is in the same subnet as the Prestige’s IP address. Note: You must enable NAT/SUA to use the Any IP feature on the Prestige. 5.5.
Prestige 660RU-Tx Series User’s Guide After all the routing information is updated, the computer can access the Prestige and the Internet as if it is in the same subnet as the Prestige. 5.6 Configuring LAN Click LAN and LAN Setup to open the following screen. Figure 17 LAN Setup The following table describes the labels in this screen.
Prestige 660RU-Tx Series User’s Guide Table 11 LAN Setup (continued) LABEL DESCRIPTION Client IP Pool Starting Address This field specifies the first of the contiguous addresses in the IP address pool. Size of Client IP Pool This field specifies the size or count of the IP address pool. Primary DNS Server Enter the IP addresses of the DNS servers. The DNS servers are passed to the DHCP clients along with the IP address and the subnet mask. Secondary DNS Server As above.
Prestige 660RU-Tx Series User’s Guide 63 Chapter 5 LAN Setup
Prestige 660RU-Tx Series User’s Guide CHAPTER 6 WAN Setup This chapter describes how to configure WAN settings. 6.1 WAN Overview A WAN (Wide Area Network) is an outside connection to another network or the Internet. See Chapter 3 Wizard Setup for more information on the fields in the WAN screens. 6.2 Metric The metric represents the "cost of transmission". A router determines the best route for transmission by choosing a path with the lowest "cost".
Prestige 660RU-Tx Series User’s Guide 6.3 PPPoE Encapsulation The Prestige supports PPPoE (Point-to-Point Protocol over Ethernet). PPPoE is an IETF Draft standard (RFC 2516) specifying how a personal computer (PC) interacts with a broadband modem (DSL, cable, wireless, etc.) connection. The PPPoE option is for a dial-up connection using PPPoE. For the service provider, PPPoE offers an access and authentication method that works with existing access control systems (for example Radius).
Prestige 660RU-Tx Series User’s Guide Figure 18 Example of Traffic Shaping 6.5 Zero Configuration Internet Access Once you turn on and connect the Prestige to a telephone jack, it automatically detects the Internet connection settings (such as the VCI/VPI numbers and the encapsulation method) from the ISP and makes the necessary configuration changes.
Prestige 660RU-Tx Series User’s Guide Figure 19 WAN Setup (PPPoE) The following table describes the labels in this screen. Table 12 WAN Setup 67 LABEL DESCRIPTION Name Enter the name of your Internet Service Provider, e.g., MyISP. This information is for identification purposes only. Mode Select Routing (default) from the drop-down list box if your ISP allows multiple computers to share an Internet account. Otherwise select Bridge.
Prestige 660RU-Tx Series User’s Guide Table 12 WAN Setup (continued) LABEL DESCRIPTION Encapsulation Select the method of encapsulation used by your ISP from the drop-down list box. Choices vary depending on the mode you select in the Mode field. If you select Bridge in the Mode field, select either PPPoA or RFC 1483. If you select Routing in the Mode field, select PPPoA, RFC 1483, ENET ENCAP or PPPoE. Multiplex Select the method of multiplexing used by your ISP from the drop-down list.
Prestige 660RU-Tx Series User’s Guide Table 12 WAN Setup (continued) LABEL DESCRIPTION Max Idle Timeout Specify an idle time-out in the Max Idle Timeout field when you select Connect on Demand. The default setting is 0, which means the Internet session will not timeout. PPPoE Passthrough This field is available when you select PPPoE encapsulation.
Prestige 660RU-Tx Series User’s Guide Figure 20 Traffic Redirect Example The following network topology allows you to avoid triangle route security issues when the backup gateway is connected to the LAN. Use IP alias to configure the LAN into two or three logical networks with the Prestige itself as the gateway for each LAN network. Put the protected LAN in one subnet (Subnet 1 in the following figure) and the backup gateway in another subnet (Subnet 2).
Prestige 660RU-Tx Series User’s Guide Figure 22 WAN Backup The following table describes the labels in this screen. Table 13 WAN Backup LABEL DESCRIPTION Backup Type Select the method that the Prestige uses to check the DSL connection. Select DSL Link to have the Prestige check if the connection to the DSLAM is up. Select ICMP to have the Prestige periodically ping the IP addresses configured in the Check WAN IP Address fields.
Prestige 660RU-Tx Series User’s Guide Table 13 WAN Backup (continued) LABEL DESCRIPTION Traffic Redirect Active Select this check box to have the Prestige use traffic redirect if the normal WAN connection goes down. Note: If you activate traffic redirect, you must configure at least one Check WAN IP Address. Metric This field sets this route's priority among the routes the Prestige uses. The metric represents the "cost of transmission".
Prestige 660RU-Tx Series User’s Guide 73 Chapter 6 WAN Setup
Prestige 660RU-Tx Series User’s Guide CHAPTER 7 Network Address Translation (NAT) Screens This chapter discusses how to configure NAT on the Prestige. 7.1 NAT Overview NAT (Network Address Translation - NAT, RFC 1631) is the translation of the IP address of a host in a packet, for example, the source address of an outgoing packet, used within one network to a different IP address known within another network. 7.1.
Prestige 660RU-Tx Series User’s Guide Note: NAT never changes the IP address (either local or global) of an outside host. 7.1.2 What NAT Does In the simplest form, NAT changes the source IP address in a packet received from a subscriber (the inside local address) to another (the inside global address) before forwarding the packet to the WAN side.
Prestige 660RU-Tx Series User’s Guide Figure 23 How NAT Works 7.1.4 NAT Application The following figure illustrates a possible NAT application, where three inside LANs (logical LANs using IP Alias) behind the Prestige can communicate with three distinct WAN networks. More examples follow at the end of this chapter. Figure 24 NAT Application With IP Alias 7.1.5 NAT Mapping Types NAT supports five types of IP/port mapping.
Prestige 660RU-Tx Series User’s Guide • One to One: In One-to-One mode, the Prestige maps one local IP address to one global IP address. • Many to One: In Many-to-One mode, the Prestige maps multiple local IP addresses to one global IP address. This is equivalent to SUA (for instance, PAT, port address translation), ZyXEL’s Single User Account feature that previous ZyXEL routers supported (the SUA Only option in today’s routers).
Prestige 660RU-Tx Series User’s Guide Note: 1. Choose SUA Only if you have just one public WAN IP address for your Prestige. 2. Choose Full Feature if you have multiple public WAN IP addresses for your Prestige. 7.3 SUA Server A SUA server set is a list of inside (behind NAT on the LAN) servers, for example, web or FTP, that you can make visible to the outside world even though SUA makes your whole inside network appear as a single computer to the outside world.
Prestige 660RU-Tx Series User’s Guide Table 16 Services and Port Numbers (continued) SERVICES PORT NUMBER SMTP (Simple Mail Transfer Protocol) 25 DNS (Domain Name System) 53 Finger 79 HTTP (Hyper Text Transfer protocol or WWW, Web) 80 POP3 (Post Office Protocol) 110 NNTP (Network News Transport Protocol) 119 SNMP (Simple Network Management Protocol) 161 SNMP trap 162 PPTP (Point-to-Point Tunneling Protocol) 1723 7.3.
Prestige 660RU-Tx Series User’s Guide Figure 26 NAT Mode The following table describes the labels in this screen. Table 17 NAT Mode LABEL DESCRIPTION None Select this radio button to disable NAT. SUA Only Select this radio button if you have just one public WAN IP address for your Prestige. The Prestige uses Address Mapping Set 1 in the NAT - Edit SUA/NAT Server Set screen. Edit Details Click this link to go to the NAT - Edit SUA/NAT Server Set screen.
Prestige 660RU-Tx Series User’s Guide Figure 27 Edit SUA/NAT Server Set The following table describes the labels in this screen. Table 18 Edit SUA/NAT Server Set LABEL 81 DESCRIPTION Start Port No. Enter a port number in this field. To forward only one port, enter the port number again in the End Port No. field. To forward a series of ports, enter the start port number here and the end port number in the End Port No. field. End Port No. Enter a port number in this field.
Prestige 660RU-Tx Series User’s Guide 7.6 Configuring Address Mapping Ordering your rules is important because the Prestige applies the rules in the order that you specify. When a rule matches the current packet, the Prestige takes the corresponding action and the remaining rules are ignored. If there are any empty rules before your new configured rule, your configured rule will be pushed up by that number of empty rules.
Prestige 660RU-Tx Series User’s Guide Table 19 Address Mapping Rules (continued) LABEL DESCRIPTION Type 1-1: One-to-one mode maps one local IP address to one global IP address. Note that port numbers do not change for the One-to-one NAT mapping type. M-1: Many-to-One mode maps multiple local IP addresses to one global IP address. This is equivalent to SUA (i.e., PAT, port address translation), ZyXEL's Single User Account feature that previous ZyXEL routers supported only.
Prestige 660RU-Tx Series User’s Guide Table 20 Address Mapping Rule Edit LABEL DESCRIPTION Type Choose the port mapping type from one of the following. • One-to-One: One-to-One mode maps one local IP address to one global IP address. Note that port numbers do not change for One-to-one NAT mapping type. • Many-to-One: Many-to-One mode maps multiple local IP addresses to one global IP address. This is equivalent to SUA (i.e.
Prestige 660RU-Tx Series User’s Guide 85 Chapter 7 Network Address Translation (NAT) Screens
Prestige 660RU-Tx Series User’s Guide CHAPTER 8 Dynamic DNS Setup This chapter discusses how to configure your Prestige to use Dynamic DNS. 8.1 Dynamic DNS Dynamic DNS allows you to update your current dynamic IP address with one or many dynamic DNS services so that anyone can contact you (in NetMeeting, CU-SeeMe, etc.). You can also access your FTP server or Web site on your own computer using a domain name (for instance myhost.dhs.
Prestige 660RU-Tx Series User’s Guide Figure 30 Dynamic DNS The following table describes the labels in this screen. Table 21 Dynamic DNS 87 LABEL DESCRIPTION Active Select this check box to use dynamic DNS. Service Provider This is the name of your Dynamic DNS service provider. Host Names Type the domain name assigned to your Prestige by your Dynamic DNS provider. E-mail Address Type your e-mail address. User Type your user name. Password Type the password assigned to you.
Prestige 660RU-Tx Series User’s Guide CHAPTER 9 Time and Date This screen is not available on all models. Use this screen to configure the Prestige’s time and date settings. 9.1 Configuring Time and Date To change your Prestige’s time and date, click Time And Date. The screen appears as shown. Use this screen to configure the Prestige’s time based on your local time zone. Figure 31 Time and Date The following table describes the labels in this screen.
Prestige 660RU-Tx Series User’s Guide Table 22 Time and Date LABEL DESCRIPTION Time Server Use Protocol when Select the time service protocol that your time server sends when you turn on the Bootup Prestige. Not all time servers support all protocols, so you may have to check with your ISP/network administrator or use trial and error to find a protocol that works. The main difference between them is the format. Daytime (RFC 867) format is day/month/year/time zone of the server.
Prestige 660RU-Tx Series User’s Guide CHAPTER 10 Remote Management Configuration This chapter provides information on configuring remote management. 10.1 Remote Management Overview Remote management allows you to determine which services/protocols can access which Prestige interface (if any) from which computers. You may manage your Prestige from a remote location via: • • • • Internet (WAN only) ALL (LAN and WAN) LAN only, Neither (Disable).
Prestige 660RU-Tx Series User’s Guide 10.1.2 Remote Management and NAT When NAT is enabled: • Use the Prestige’s WAN IP address when configuring from the WAN. • Use the Prestige’s LAN IP address when configuring from the LAN. 10.1.3 System Timeout There is a default system management idle timeout of five minutes (three hundred seconds). The Prestige automatically logs you out if the management session remains idle for longer than this timeout period.
Prestige 660RU-Tx Series User’s Guide Figure 33 Remote Management The following table describes the labels in this screen. Table 23 Remote Management LABEL DESCRIPTION Server Type Each of these labels denotes a service that you may use to remotely manage the Prestige. Access Status Select the access interface. Choices are All, LAN Only, WAN Only and Disable. Port This field shows the port number for the remote management service.
Prestige 660RU-Tx Series User’s Guide 93 Chapter 10 Remote Management Configuration
Prestige 660RU-Tx Series User’s Guide C H A P T E R 11 Universal Plug-and-Play (UPnP) This chapter introduces the UPnP feature in the web configurator. 11.1 Introducing Universal Plug and Play Universal Plug and Play (UPnP) is a distributed, open networking standard that uses TCP/IP for simple peer-to-peer network connectivity between devices. A UPnP device can dynamically join a network, obtain an IP address, convey its capabilities and learn about other devices on the network.
Prestige 660RU-Tx Series User’s Guide All UPnP-enabled devices may communicate freely with each other without additional configuration. Disable UPnP if this is not your intention. 11.2 UPnP and ZyXEL ZyXEL has achieved UPnP certification from the Universal Plug and Play Forum Creates UPnP™ Implementers Corp. (UIC). ZyXEL's UPnP implementation supports IGD 1.0 (Internet Gateway Device). At the time of writing ZyXEL's UPnP implementation supports Windows Messenger 4.6 and 4.7 while Windows Messenger 5.
Prestige 660RU-Tx Series User’s Guide 11.3 Installing UPnP in Windows Example This section shows how to install UPnP in Windows Me and Windows XP. Installing UPnP in Windows Me Follow the steps below to install the UPnP in Windows Me. 1 Click Start and Control Panel. Double-click Add/Remove Programs. 2 Click on the Windows Setup tab and select Communication in the Components selection box. Click Details.
Prestige 660RU-Tx Series User’s Guide Figure 36 Add/Remove Programs: Windows Setup: Communication: Components 4 Click OK to go back to the Add/Remove Programs Properties window and click Next. 5 Restart the computer when prompted. Installing UPnP in Windows XP Follow the steps below to install the UPnP in Windows XP. 1 Click Start and Control Panel. 2 Double-click Network Connections. 3 In the Network Connections window, click Advanced in the main menu and select Optional Networking Components ….
Prestige 660RU-Tx Series User’s Guide Figure 38 Windows Optional Networking Components Wizard 5 In the Networking Services window, select the Universal Plug and Play check box.
Prestige 660RU-Tx Series User’s Guide Figure 39 Networking Services 6 Click OK to go back to the Windows Optional Networking Component Wizard window and click Next. 11.4 Using UPnP in Windows XP Example This section shows you how to use the UPnP feature in Windows XP. You must already have UPnP installed in Windows XP and UPnP activated on the Prestige. Make sure the computer is connected to a LAN port of the Prestige. Turn on your computer and the Prestige.
Prestige 660RU-Tx Series User’s Guide Figure 40 Network Connections 3 In the Internet Connection Properties window, click Settings to see the port mappings there were automatically created.
Prestige 660RU-Tx Series User’s Guide Figure 41 Internet Connection Properties 4 You may edit or delete the port mappings or click Add to manually add port mappings.
Prestige 660RU-Tx Series User’s Guide Figure 42 Internet Connection Properties: Advanced Settings Figure 43 Internet Connection Properties: Advanced Settings: Add 5 When the UPnP-enabled device is disconnected from your computer, all port mappings will be deleted automatically. 6 Select Show icon in notification area when connected option and click OK. An icon displays in the system tray.
Prestige 660RU-Tx Series User’s Guide Figure 44 System Tray Icon 7 Double-click on the icon to display your current Internet connection status. Figure 45 Internet Connection Status Web Configurator Easy Access With UPnP, you can access the web-based configurator on the Prestige without finding out the IP address of the Prestige first. This comes helpful if you do not know the IP address of the Prestige. Follow the steps below to access the web configurator. 1 Click Start and then Control Panel.
Prestige 660RU-Tx Series User’s Guide Figure 46 Network Connections 4 An icon with the description for each UPnP-enabled device displays under Local Network. 5 Right-click on the icon for your Prestige and select Invoke. The web configurator login screen displays.
Prestige 660RU-Tx Series User’s Guide Figure 47 Network Connections: My Network Places 6 Right-click on the icon for your Prestige and select Properties. A properties window displays with basic information about the Prestige.
Prestige 660RU-Tx Series User’s Guide Figure 48 Network Connections: My Network Places: Properties: Example Chapter 11 Universal Plug-and-Play (UPnP) 106
Prestige 660RU-Tx Series User’s Guide 107 Chapter 11 Universal Plug-and-Play (UPnP)
Prestige 660RU-Tx Series User’s Guide CHAPTER 12 Maintenance This chapter displays system information such as ZyNOS firmware, port IP addresses and port traffic statistics. 12.1 Maintenance Overview The maintenance screens can help you view system information, upload new firmware, manage configuration and restart your Prestige. 12.2 System Status Screen Click System Status to open the following screen, where you can use to monitor your Prestige.
Prestige 660RU-Tx Series User’s Guide Figure 49 System Status The following table describes the fields in this screen. Table 25 System Status LABEL DESCRIPTION System Status System Name This is the name of your Prestige. It is for identification purposes. ZyNOS Firmware Version This is the ZyNOS firmware version and the date the firmware was created. ZyNOS is ZyXEL's proprietary Network Operating System design. DSL FW Version This is the DSL firmware version associated with your Prestige.
Prestige 660RU-Tx Series User’s Guide Table 25 System Status (continued) LABEL DESCRIPTION IP Subnet Mask This is the WAN port IP subnet mask. Default Gateway This is the IP address of the default gateway, if applicable. VPI/VCI This is the Virtual Path Identifier and Virtual Channel Identifier that you entered in the first Wizard screen. LAN Information MAC Address This is the MAC (Media Access Control) or Ethernet address unique to your Prestige. IP Address This is the LAN port IP address.
Prestige 660RU-Tx Series User’s Guide The following table describes the labels in this screen. Table 26 System Status: Show Statistics LABEL DESCRIPTION System up Time This is the elapsed time the system has been up. CPU Load This field specifies the percentage of CPU utilization. LAN or WAN Port Statistics This is the WAN or LAN port. Link Status This is the status of your WAN link. Upstream Speed This is the upstream speed of your Prestige.
Prestige 660RU-Tx Series User’s Guide Figure 51 DHCP Table The following table describes the fields in this screen. Table 27 DHCP Table LABEL DESCRIPTION Host Name This is the name of the host computer. IP Address This field displays the IP address relative to the Host Name field. MAC Address This field displays the MAC (Media Access Control) address of the computer with the displayed host name. Every Ethernet device has a unique MAC address.
Prestige 660RU-Tx Series User’s Guide Table 28 Any IP Table LABEL DESCRIPTION MAC Address This field displays the MAC (Media Access Control) address of the computer with the displayed IP address. Every Ethernet device has a unique MAC address. The MAC address is assigned at the factory and consists of six pairs of hexadecimal characters, for example, 00:A0:C5:00:00:02. Refresh Click Refresh to update this screen. 12.
Prestige 660RU-Tx Series User’s Guide Figure 53 Diagnostic: General The following table describes the labels in this screen. Table 29 Diagnostic: General LABEL DESCRIPTION TCP/IP Address Type the IP address of a computer that you want to ping in order to test a connection. Ping Click this button to ping the IP address that you entered. Reset System Click this button to reboot the Prestige. A warning dialog box is then displayed asking you if you're sure you want to reboot the system.
Prestige 660RU-Tx Series User’s Guide Figure 54 Diagnostic: DSL Line The following table describes the labels in this screen. Table 30 Diagnostic: DSL Line LABEL Reset ADSL Line DESCRIPTION Click this button to reinitialize the ADSL line. The large text box above then displays the progress and results of this operation, for example: "Start to reset ADSL Loading ADSL modem F/W... Reset ADSL Line Successfully!" 115 ATM Status Click this button to view ATM status.
Prestige 660RU-Tx Series User’s Guide 12.6 Firmware Screen Find firmware at www.zyxel.com in a file that (usually) uses the system model name with a .bin extension, for example, "Prestige.bin". The upload process uses HTTP (Hypertext Transfer Protocol) and may take up to two minutes. After a successful upload, the system will reboot. See Chapter 25 Firmware and Configuration File Maintenance in the parts that document the SMT for upgrading firmware using FTP/TFTP commands.
Prestige 660RU-Tx Series User’s Guide After you see the Firmware Upload in Process screen, wait two minutes before logging into the Prestige again. The Prestige automatically restarts in this time causing a temporary network disconnect. In some operating systems, you may see the following icon on your desktop. Figure 56 Network Temporarily Disconnected After two minutes, log in again and check your new firmware version in the System Status screen.
Prestige 660RU-Tx Series User’s Guide CHAPTER 13 Introducing the SMT This chapter explains how to access and navigate the System Management Terminal and gives an overview of its menus. 13.1 SMT Introduction The Prestige’s SMT (System Management Terminal) is a menu-driven interface that you can access from a terminal emulator over a telnet connection. This chapter shows you how to access the SMT (System Management Terminal) menus via Telnet, how to navigate the SMT and how to configure SMT menus. 13.1.
Prestige 660RU-Tx Series User’s Guide Figure 58 Login Screen Enter Password : **** 13.1.3 Prestige SMT Menu Overview The following figure gives you an overview of the various SMT menu screens of your Prestige. Figure 59 Prestige SMT Menu Overview 13.2 Navigating the SMT Interface The SMT (System Management Terminal) is the interface that you use to configure your Prestige.
Prestige 660RU-Tx Series User’s Guide Several operations that you should be familiar with before you attempt to modify the configuration are listed in the table below. Table 32 Navigating the SMT Interface OPERATION KEY STROKE DESCRIPTION Move down to another menu [ENTER] To move forward to a submenu, type in the number of the desired submenu and press [ENTER]. Move up to a previous menu [ESC] Press [ESC] to move back to the previous menu.
Prestige 660RU-Tx Series User’s Guide After you enter the password, the SMT displays the main menu, as shown next. Table 33 SMT Main Menu Copyright (c) 1994 - 2004 ZyXEL Communications Corp. Prestige 660RU-T1 Main Menu Getting Started 1. General Setup 2. WAN Backup Setup 3. LAN Setup 4. Internet Access Setup Advanced Applications 11. Remote Node Setup 12. Static Routing Setup 15. NAT Setup Advanced Management 21. Filter Set Configuration 22. SNMP Configuration 23. System Password 24.
Prestige 660RU-Tx Series User’s Guide 13.3 Changing the System Password Change the Prestige default password by following the steps shown next. 1 Enter 23 in the main menu to display Menu 23 - System Password as shown next. 2 Type your existing system password in the Old Password field, for example “1234", and press [ENTER].
Prestige 660RU-Tx Series User’s Guide 123 Chapter 13 Introducing the SMT
Prestige 660RU-Tx Series User’s Guide CHAPTER 14 Menu 1 General Setup Menu 1 - General Setup contains administrative and system-related information. 14.1 General Setup Menu 1 — General Setup contains administrative and system-related information (shown next). The System Name field is for identification purposes. However, because some ISPs check this name you should enter your computer's "Computer Name". • In Windows 95/98 click Start, Settings, Control Panel, Network.
Prestige 660RU-Tx Series User’s Guide Figure 61 Menu 1 General Setup Menu 1 General Setup System Name= ? Location= Contact Person's Name= Domain Name= Edit Dynamic DNS= No Route IP= Yes Bridge= No Press ENTER to Confirm or ESC to Cancel: Fill in the required fields. Refer to the table shown next for more information about these fields. Table 35 Menu 1 General Setup FIELD DESCRIPTION System Name Choose a descriptive name for identification purposes. This name can be up to 30 alphanumeric characters long.
Prestige 660RU-Tx Series User’s Guide To configure dynamic DNS, go to Menu 1 — General Setup and select Yes in the Edit Dynamic DNS field. Press [ENTER] to display Menu 1.1— Configure Dynamic DNS as shown next. Figure 62 Menu 1.1 Configure Dynamic DNS Menu 1.1 - Configure Dynamic DNS Service Provider= WWW.DynDNS.ORG Active= Yes Host= me.dyndns.
Prestige 660RU-Tx Series User’s Guide 127 Chapter 14 Menu 1 General Setup
Prestige 660RU-Tx Series User’s Guide CHAPTER 15 Menu 2 WAN Backup Setup This chapter describes how to configure traffic redirect using menu 2 and 2.1. 15.1 Introduction to WAN Backup Setup This chapter explains how to configure the Prestige for traffic redirect and dial backup connections. 15.2 Configuring Dial Backup in Menu 2 From the main menu, enter 2 to open menu 2. Figure 63 Menu 2 WAN Backup Setup Menu 2 - Wan Backup Setup Check Mechanism = DSL Link Check WAN IP Address1 = 0.0.0.
Prestige 660RU-Tx Series User’s Guide The following table describes the fields in this menu. Table 37 Menu 2 WAN Backup Setup FIELD DESCRIPTION Check Mechanism Press [SPACE BAR] and then press [ENTER] to select the method that the Prestige uses to check the DSL connection. Select DSL Link to have the Prestige check the DSL connection’s physical layer. Select ICMP to have the Prestige periodically ping the IP addresses configured in the Check WAN IP Address fields.
Prestige 660RU-Tx Series User’s Guide Figure 64 Menu 2.1Traffic Redirect Setup Menu 2.1 - Traffic Redirect Setup Active= No Configuration: Backup Gateway IP Address= 0.0.0.0 Metric= 15 Press ENTER to Confirm or ESC to Cancel: The following table describes the fields in this menu. Table 38 Menu 2.1Traffic Redirect Setup FIELD DESCRIPTION Active. Press [SPACE BAR] and select Yes (to enable) or No (to disable) traffic redirect setup.
Prestige 660RU-Tx Series User’s Guide 131 Chapter 15 Menu 2 WAN Backup Setup
Prestige 660RU-Tx Series User’s Guide CHAPTER 16 Menu 3 LAN Setup This chapter covers how to configure your wired Local Area Network (LAN) settings. 16.1 LAN Setup This section describes how to configure the Ethernet using Menu 3 — LAN Setup. From the main menu, enter 3 to display menu 3. Figure 65 Menu 3 LAN Setup Menu 3 - LAN Setup 1. LAN Port Filter Setup 2. TCP/IP and DHCP Setup Enter Menu Selection Number: 16.1.
Prestige 660RU-Tx Series User’s Guide 16.2 Protocol Dependent Ethernet Setup Depending on the protocols for your applications, you need to configure the respective Ethernet Setup, as outlined below. • For TCP/IP Ethernet setup refer to the Internet Access Configuration section. • For bridging Ethernet setup refer to Chapter 20 Bridging Setup. 16.3 CP/IP Ethernet Setup and DHCP Use menu 3.2 to configure your Prestige for TCP/IP. To edit menu 3.2, enter 3 from the main menu to display Menu 3 — LAN Setup.
Prestige 660RU-Tx Series User’s Guide Follow the instructions in the following table on how to configure the DHCP fields. Table 39 DHCP Ethernet Setup FIELD DESCRIPTION DHCP Setup DHCP If set to Server, your Prestige can assign IP addresses, an IP default gateway and DNS servers to Windows 95, Windows NT and other systems that support the DHCP client. If set to None, the DHCP server will be disabled.
Prestige 660RU-Tx Series User’s Guide 135 Chapter 16 Menu 3 LAN Setup
Prestige 660RU-Tx Series User’s Guide CHAPTER 17 Internet Access This chapter shows you how to configure the LAN and WAN of your Prestige for Internet access. 17.1 Internet Access Overview Refer to the chapters on the web configurator’s wizard, LAN and WAN screens for more background information on fields in the SMT screens covered in this chapter. 17.2 IP Policies Traditionally, routing is based on the destination address only and the router takes the shortest path to forward a packet.
Prestige 660RU-Tx Series User’s Guide Figure 68 IP Alias Network Example Use menu 3.2.1 to configure IP Alias on your Prestige. 17.4 IP Alias Setup Use menu 3.2 to configure the first network. Move the cursor to Edit IP Alias field and press [SPACEBAR] to choose Yes and press [ENTER] to configure the second and third network. Figure 69 Menu 3.2 TCP/IP and DHCP Setup Menu 3.2 - TCP/IP and DHCP Setup DHCP Setup DHCP= Server Client IP Pool Starting Address= 192.168.1.
Prestige 660RU-Tx Series User’s Guide Figure 70 Menu 3.2.1 IP Alias Setup Menu 3.2.1 - IP Alias Setup IP Alias 1= Yes IP Address= 192.168.2.1 IP Subnet Mask= 255.255.255.
Prestige 660RU-Tx Series User’s Guide Figure 71 Menu 1 General Setup Menu 1 - General Setup System Name= ? Location= location Contact Person's Name= Domain Name= Edit Dynamic DNS= No Route IP= Yes Bridge= No Press ENTER to Confirm or ESC to Cancel: 17.6 Internet Access Configuration Menu 4 allows you to enter the Internet Access information in one screen. Menu 4 is actually a simplified setup for one of the remote nodes that you can access in menu 11.
Prestige 660RU-Tx Series User’s Guide Figure 72 Menu 4 Internet Access Setup Menu 4 - Internet Access Setup ISP's Name= MyISP Encapsulation= RFC 1483 Multiplexing= LLC-based VPI #= 8 VCI #= 35 ATM QoS Type= CBR Peak Cell Rate (PCR)= 0 Sustain Cell Rate (SCR)= 0 Maximum Burst Size (MBS)= 0 My Login= N/A My Password= N/A ENET ENCAP Gateway= N/A IP Address Assignment= Static IP Address= 0.0.0.
Prestige 660RU-Tx Series User’s Guide Table 42 Menu 4 Internet Access Setup (continued) FIELD DESCRIPTION My Password Enter the password associated with the login name above. ENET ENCAP Gateway Enter the gateway IP address supplied by your ISP when you are using ENET ENCAP encapsulation. Idle Timeout This value specifies the number of idle seconds that elapse before the Prestige automatically disconnects the PPPoE session.
Prestige 660RU-Tx Series User’s Guide CHAPTER 18 Remote Node Configuration This chapter covers remote node configuration. 18.1 Remote Node Setup Overview This section describes the protocol-independent parameters for a remote node. A remote node is required for placing calls to a remote gateway. A remote node represents both the remote gateway and the network behind it across a WAN connection. When you use menu 4 to set up Internet access, you are configuring one of the remote nodes.
Prestige 660RU-Tx Series User’s Guide Figure 73 Menu 11 Remote Node Setup Menu 11 - Remote Node Setup 1. 2. 3. 4. 5. 6. 7. 8. MyISP (ISP, SUA) ________ ________ ________ ________ ________ ________ ________ Enter Node # to Edit: 18.2.2 Encapsulation and Multiplexing Scenarios For Internet access you should use the encapsulation and multiplexing methods used by your ISP.
Prestige 660RU-Tx Series User’s Guide Figure 74 Menu 11.1 Remote Node Profile Menu 11.
Prestige 660RU-Tx Series User’s Guide Table 43 Menu 11.1 Remote Node Profile (continued) FIELD DESCRIPTION Authen This field sets the authentication protocol used for outgoing calls. Options for this field are: CHAP/PAP – Your Prestige will accept either CHAP or PAP when requested by this remote node. CHAP – accept CHAP (Challenge Handshake Authentication Protocol) only. PAP – accept PAP (Password Authentication Protocol) only. Route This field determines the protocol used in routing.
Prestige 660RU-Tx Series User’s Guide 18.3 Remote Node Network Layer Options For the TCP/IP parameters, perform the following steps to edit Menu 11.3 – Remote Node Network Layer Options as shown next. 1 In menu 11.1, make sure IP is among the protocols in the Route field. 2 Move the cursor to the Edit IP/Bridge field, press [SPACE BAR] to select Yes, then press [ENTER] to display Menu 11.3 – Remote Node Network Layer Options. Figure 75 Menu 11.3 Remote Node Network Layer Options Menu 11.
Prestige 660RU-Tx Series User’s Guide Table 44 Menu 11.3 Remote Node Network Layer Options (continued) FIELD DESCRIPTION Address Mapping Set When Full Feature is selected in the NAT field, configure address mapping sets in menu 15.1. Select one of the NAT server sets (2-10) in menu 15.2 (see Chapter 21 Network Address Translation (NAT) for details) and type that number here. When SUA Only is selected in the NAT field, the SMT uses NAT server set 1 in menu 15.
Prestige 660RU-Tx Series User’s Guide Figure 76 Sample IP Addresses for a TCP/IP LAN-to-LAN Connection 18.4 Remote Node Filter Move the cursor to the Edit Filter Sets field in menu 11.1, then press [SPACE BAR] to select Yes. Press [ENTER] to display Menu 11.5 – Remote Node Filter. Use Menu 11.5 – Remote Node Filter to specify the filter set(s) to apply to the incoming and outgoing traffic between this remote node and the Prestige and also to prevent certain packets from triggering calls.
Prestige 660RU-Tx Series User’s Guide Figure 78 Menu 11.5 Remote Node Filter (PPPoA or PPPoE Encapsulation) Menu 11.5 - Remote Node Filter Input Filter Sets: protocol filters= 1, 5, 9, 12 device filters= Output Filter Sets: protocol filters= device filters= Call Filter Sets: protocol filters= device filters= Enter here to CONFIRM or ESC to CANCEL: 18.4.1 Web Configurator Internet Security Filter Rules In the web configurator, open the Security screen as shown next.
Prestige 660RU-Tx Series User’s Guide 18.4.2 Web Configurator Filter Sets When you apply filter rules using the web configurator, filter sets 11 and 12 are automatically generated in SMT menu 21. This feature is not available on all models.
Prestige 660RU-Tx Series User’s Guide Figure 82 Menu 21.12 WebSet 12 Menu 21.12 - Filter Rules Summary # 1 2 3 4 5 6 A Y Y Y Y N N Type ---IP IP IP IP Filter Rules ----------------------------------------------------------Pr=6, SA=0.0.0.0, DA=0.0.0.0, DP=23 Pr=6, SA=0.0.0.0, DA=0.0.0.0, DP=21 Pr=17, SA=0.0.0.0, DA=0.0.0.0, DP=69 Pr=6, SA=0.0.0.0, DA=0.0.0.0, DP=80 M N N N N m D D D D n N N N N Enter Filter Rule Number (1-6) to Configure Note: Do not edit filter sets 11 and 12.
Prestige 660RU-Tx Series User’s Guide Figure 83 Menu 11.6 for VC-based Multiplexing Menu 11.6 - Remote Node ATM Layer Options VPI/VCI (VC-Multiplexing) VC Options for IP: VPI #= 8 VCI #= 35 ATM QoS Type= UBR Peak Cell Rate (PCR)= 0 Sustain Cell Rate (SCR)= 0 Maximum Burst Size (MBS)= 0 VC Options for Bridge: VPI #= 1 VCI #= 36 ATM QoS Type= N/A Peak Cell Rate (PCR)= N/A Sustain Cell Rate (SCR)= N/A Maximum Burst Size (MBR)= N/A Press ENTER to Confirm or ESC to Cancel: 18.5.
Prestige 660RU-Tx Series User’s Guide Figure 85 Menu 11.1 Remote Node Profile Menu 11.
Prestige 660RU-Tx Series User’s Guide CHAPTER 19 Static Route Setup This chapter shows how to setup IP static routes. 19.1 IP Static Route Overview Static routes tell the Prestige routing information that it cannot learn automatically through other means. This can arise in cases where RIP is disabled on the LAN or a remote network is beyond the one that is directly connected to a remote node.
Prestige 660RU-Tx Series User’s Guide Figure 88 Menu 12 Static Route Setup Menu 12 - Static Route Setup 1. IP Static Route 3. Bridge Static Route Please enter selection: 2 From menu 12, select 1 to open Menu 12.1 — IP Static Route Setup (shown next). Figure 89 Menu 12.1 IP Static Route Setup Menu 12.1 - IP Static Route Setup 1. ________ 2. ________ 3. ________ 4. ________ 5. ________ 6. ________ 7. ________ 8. ________ 9. ________ 10. ________ 11. ________ 12. ________ 13. ________ 14. ________ 15.
Prestige 660RU-Tx Series User’s Guide The following table describes the fields for Menu 12.1.1 – Edit IP Static Route Setup. Table 46 Menu12.1.1 Edit IP Static Route FIELD DESCRIPTION Route # This is the index number of the static route that you chose in menu 12.1. Route Name Type a descriptive name for this route. This is for identification purpose only. Active This field allows you to activate/deactivate this static route.
Prestige 660RU-Tx Series User’s Guide 157 Chapter 19 Static Route Setup
Prestige 660RU-Tx Series User’s Guide CHAPTER 20 Bridging Setup This chapter shows you how to configure the bridging parameters of your Prestige. 20.1 Bridging in General Bridging bases the forwarding decision on the MAC (Media Access Control), or hardware address, while routing does it on the network layer (IP) address. Bridging allows the Prestige to transport packets of network layer protocols that it does not route, for example, SNA, from one network to another.
Prestige 660RU-Tx Series User’s Guide Figure 91 Menu 11.1 Remote Node Profile Menu 11.
Prestige 660RU-Tx Series User’s Guide Table 47 Remote Node Network Layer Options: Bridge Fields (continued) FIELD DESCRIPTION Edit IP/Bridge (menu 11.1) Press [SPACE BAR] to select Yes and press [ENTER] to display menu 11.3. Ethernet Addr Timeout (min.) (menu 11.3) Type the time (in minutes) for the Prestige to retain the Ethernet Address information in its internal tables while the line is down.
Prestige 660RU-Tx Series User’s Guide 161 Chapter 20 Bridging Setup
Prestige 660RU-Tx Series User’s Guide CHAPTER 21 Network Address Translation (NAT) This chapter discusses how to configure NAT on the Prestige. 21.1 SUA (Single User Account) Versus NAT SUA (Single User Account) is a ZyNOS implementation of a subset of NAT that supports two types of mapping, Many-to-One and Server. See the NAT Setup section or a detailed description of the NAT set for SUA.
Prestige 660RU-Tx Series User’s Guide Figure 94 Menu 4 Applying NAT for Internet Access Menu 4 - Internet Access Setup ISP's Name= MyISP Encapsulation= RFC 1483 Multiplexing= LLC-based VPI #= 8 VCI #= 35 ATM QoS Type= UBR Peak Cell Rate (PCR)= 0 Sustain Cell Rate (SCR)= 0 Maximum Burst Size (MBS)= 0 My Login= N/A My Password= N/A ENET ENCAP Gateway= N/A IP Address Assignment= Static IP Address= 0.0.0.
Prestige 660RU-Tx Series User’s Guide Table 49 Applying NAT in Menus 4 & 11.3 FIELD DESCRIPTION NAT Press [SPACE BAR] and then [ENTER] to select Full Feature if you have multiple public WAN IP addresses for your Prestige. The SMT uses the address mapping set that you configure and enter in the Address Mapping Set field (see the Address Mapping Sets section). Select None to disable NAT. When you select SUA Only, the SMT uses Address Mapping Set 255 (see the Address Mapping Sets section).
Prestige 660RU-Tx Series User’s Guide Figure 97 Menu 15.1 Address Mapping Sets Menu 15.1 - Address Mapping Sets 1. ACL Default Set 2. 3. 4. 5. 6. 7. 8. 255. SUA (read only) Enter Menu Selection Number: 21.3.1.1 SUA Address Mapping Set Enter 255 to display the next screen (see also the SUA (Single User Account) Versus NAT section). The fields in this menu cannot be changed. Figure 98 Menu 15.1.255 SUA Address Mapping Rules Set Idx --1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Menu 15.1.
Prestige 660RU-Tx Series User’s Guide Table 50 SUA Address Mapping Rules (continued) FIELD DESCRIPTION Local End IP Local End IP is the ending local IP address (ILA). If the rule is for all local IPs, then the Start IP is 0.0.0.0 and the End IP is 255.255.255.255. Global Start IP This is the starting global IP address (IGA). If you have a dynamic IP, enter 0.0.0.0 as the Global Start IP. Global End IP This is the ending global IP address (IGA). Type These are the mapping types.
Prestige 660RU-Tx Series User’s Guide 21.3.1.3 Ordering Your Rules Ordering your rules is important because the Prestige applies the rules in the order that you specify. When a rule matches the current packet, the Prestige takes the corresponding action and the remaining rules are ignored. If there are any empty rules before your new configured rule, your configured rule will be pushed up by that number of empty rules.
Prestige 660RU-Tx Series User’s Guide Figure 100 Menu 15.1.1.1 Editing/Configuring an Individual Rule in a Set Menu 15.1.1.1 Address Mapping Rule Type= One-to-One Local IP: Start= End = N/A Global IP: Start= End = N/A Server Mapping Set= N/A Press ENTER to Confirm or ESC to Cancel: The following table explains the fields in this menu. Table 52 Menu 15.1.1.1 Editing/Configuring an Individual Rule in a Set FIELD DESCRIPTION Type Press [SPACE BAR] and then [ENTER] to select from a total of five types.
Prestige 660RU-Tx Series User’s Guide Figure 101 Menu 15.2 NAT Server Setup Menu 15.2 - NAT Server Sets 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Server Server Server Server Server Server Server Server Server Server Set Set Set Set Set Set Set Set Set Set 1 (Used for SUA Only) 2 3 4 5 6 7 8 9 10 Enter Set Number to Edit: 3 Enter 1 to go to Menu 15.2.1 NAT Server Setup as follows. Figure 102 Menu 15.2.1 NAT Server Setup Menu 15.2 - NAT Server Setup Rule Start Port No. End Port No.
Prestige 660RU-Tx Series User’s Guide Figure 103 Multiple Servers Behind NAT Example 21.5 General NAT Examples The following are some examples of NAT configuration. 21.5.1 Example 1: Internet Access Only In the following Internet access example, you only need one rule where your ILAs (Inside Local addresses) all map to one dynamic IGA (Inside Global Address) assigned by your ISP.
Prestige 660RU-Tx Series User’s Guide Figure 105 Menu 4 Internet Access & NAT Example Menu 4 - Internet Access Setup ISP's Name= MyISP Encapsulation= RFC 1483 Multiplexing= LLC-based VPI #= 8 VCI #= 35 ATM QoS Type= UBR Peak Cell Rate (PCR)= 0 Sustain Cell Rate (SCR)= 0 Maximum Burst Size (MBS)= 0 My Login= N/A My Password= N/A ENET ENCAP Gateway= N/A IP Address Assignment= Static IP Address= 0.0.0.
Prestige 660RU-Tx Series User’s Guide Figure 107 Menu 15.2.1 Specifying an Inside Server Menu 15.2.1 - NAT Server Setup (Used for SUA Only) Rule Start Port No. End Port No. IP Address --------------------------------------------------1. Default Default 192.168.1.10 2. 0 0 0.0.0.0 3. 0 0 0.0.0.0 4. 0 0 0.0.0.0 5. 0 0 0.0.0.0 6. 0 0 0.0.0.0 7. 0 0 0.0.0.0 8. 0 0 0.0.0.0 9. 0 0 0.0.0.0 10. 0 0 0.0.0.0 11. 0 0 0.0.0.0 12. 0 0 0.0.0.0 Press ENTER to Confirm or ESC to Cancel: 21.5.
Prestige 660RU-Tx Series User’s Guide Figure 108 NAT Example 3 In this case you need to configure Address Mapping Set 1 from Menu 15.1 - Address Mapping Sets. Therefore you must choose the Full Feature option from the Network Address Translation field (in menu 4 or menu 11.3) in Figure 109. 1 Enter 15 from the main menu. 2 Enter 1 to configure the Address Mapping Sets. 3 Enter 1 to begin configuring this new set. Enter a Set Name, choose the Edit Action and then enter 1 for the Select Rule field.
Prestige 660RU-Tx Series User’s Guide Figure 110 Example 3: Menu 15.1.1.1 Menu 15.1.1.1 Address Mapping Rule Type= One-to-One Local IP: Start= 192.168.1.10 End = N/A Global IP: Start= 10.132.50.1 End = N/A Server Mapping Set= N/A Press ENTER to Confirm or ESC to Cancel: Figure 111 Example 3: Final Menu 15.1.1 Menu 15.1.1 - Address Mapping Rules Set Idx --1. 2 3. 4. 5. 6. 7. 8. 9. 10. Name= Example3 Local Start IP Local End IP Global Start IP -------------- -------------- --------------192.168.1.10 10.132.
Prestige 660RU-Tx Series User’s Guide Figure 112 Example 3: Menu 15.2.1 Menu 15.2.1 - NAT Server Setup Rule Start Port No. End Port No. IP Address --------------------------------------------------1. Default Default 0.0.0.0 2. 80 80 192.168.1.21 3. 25 25 192.168.1.20 4. 0 0 0.0.0.0 5. 0 0 0.0.0.0 6. 0 0 0.0.0.0 7. 0 0 0.0.0.0 8. 0 0 0.0.0.0 9. 0 0 0.0.0.0 10. 0 0 0.0.0.0 11. 0 0 0.0.0.0 12. 0 0 0.0.0.0 Press ENTER to Confirm or ESC to Cancel: 21.5.
Prestige 660RU-Tx Series User’s Guide Figure 114 Example 4: Menu 15.1.1.1 Address Mapping Rule Menu 15.1.1.1 Address Mapping Rule Type= Many-to-Many No Overload Local IP: Start= 192.168.1.10 End = 192.168.1.12 Global IP: Start= 10.132.50.1 End = 10.132.50.3 Server Mapping Set= N/A Press ENTER to Confirm or ESC to Cancel: After you’ve configured your rule, you should be able to check the settings in menu 15.1.1 as shown next. Figure 115 Example 4: Menu 15.1.1 Address Mapping Rules Menu 15.1.
Prestige 660RU-Tx Series User’s Guide 177 Chapter 21 Network Address Translation (NAT)
Prestige 660RU-Tx Series User’s Guide CHAPTER 22 Filter Configuration This chapter shows you how to create and apply filters. 22.1 About Filtering Your Prestige uses filters to decide whether or not to allow passage of a data packet and/or to make a call. There are two types of filter applications: data filtering and call filtering. Filters are subdivided into device and protocol filters, which are discussed later. Data filtering screens data to determine if the packet should be allowed to pass.
Prestige 660RU-Tx Series User’s Guide Figure 117 Filter Rule Process Start Packet intoFilter Fetch First Filter Set Filter Set Fetch Next Filter Set Fetch First Filter Rule Fetch Next Filter Rule Yes Yes Next Filter Set Available? No Next filter Rule Available? No Active? Yes Execute Filter Rule No Check Next Rule Forward Drop Drop Packet Accept Packet You can apply up to four filter sets to a particular port to block various types of packets.
Prestige 660RU-Tx Series User’s Guide 22.2 Configuring a Filter Set for the Prestige To configure a filter set, follow the steps shown next. 1 Enter 21 in the main menu to display Menu 21 – Filter Set Configuration as shown next.
Prestige 660RU-Tx Series User’s Guide Figure 120 NetBIOS_LAN Filter Rules Summary Menu 21.1.3 - Filter Rules Summary # 1 2 3 4 5 6 A Type Filter Rules M m n - ---- ------------------------------------------------------------- - Y IP N N N N N Pr=17, SA=0.0.0.0, SP=137, DA=0.0.0.0, DP=53 N D F Enter Filter Rule Number (1-6) to Configure: 22.3 Filter Rules Summary Menus The following tables briefly describe the abbreviations used in menus 21.1.1 and 21.1.2.
Prestige 660RU-Tx Series User’s Guide The protocol dependent filter rules abbreviation are listed as follows: Table 54 Rule Abbreviations Used FILTER TYPE DESCRIPTION IP Pr Protocol SA Source Address SP Source Port Number DA Destination Address DP Destination Port Number GEN Off Offset Len Length 22.4 Configuring a Filter Rule To configure a filter rule, type its number in Menu 21.x – Filter Rules Summary and press [ENTER] to open menu 21.x.1 for the rule.
Prestige 660RU-Tx Series User’s Guide Figure 121 Menu 21.x.1 TCP/IP Filter Rule Menu 21.1.
Prestige 660RU-Tx Series User’s Guide Table 55 Menu 21.x.1 TCP/IP Filter Rule (continued) FIELD DESCRIPTION Port # Type the source port of the packets you want to filter. The range of this field is 0 to 65535. A 0 field is ignored. Port # Comp Select the comparison to apply to the source port in the packet against the value given in Source: Port # field. Choices are None, Less, Greater, Equal or Not Equal. TCP Estab This applies only when the IP Protocol field is 6, TCP.
Prestige 660RU-Tx Series User’s Guide Figure 122 Executing an IP Filter Packet into IP Filter Filter Active? No Yes Apply SrcAddrMask to Src Addr Check Src IP Addr Not Matched Matched Apply DestAddrMask to Dest Addr Check Dest IP Addr Not Matched Matched Check IP Protocol Not Matched Matched Check Src & Dest Port Not Matched Matched More? Yes No Action Matched Drop Action Not Matched Check Next Rule Check Next Rule Drop Forward Forward Drop Packet Check Next Rule Accept Packet 22.4.
Prestige 660RU-Tx Series User’s Guide To configure a generic rule select an empty filter set in menu 21, for example 5. Select Generic Filter Rule in the Filter Type field and press [ENTER] to open Menu 21.5.1 – Generic Filter Rule, as shown in the following figure. Figure 123 Menu 21.5.1 Generic Filter Rule Menu 21.5.
Prestige 660RU-Tx Series User’s Guide Table 56 Menu 21.1.5.1 Generic Filter Rule (continued) FIELD DESCRIPTION Action Not Matched Select the action for a packet not matching the rule. Choices are Check Next Rule, Forward or Drop. When you have completed this menu, press [ENTER] at the prompt “Press ENTER to Confirm or ESC to Cancel:” to save your configuration, or press [ESC] at any time to cancel. 22.
Prestige 660RU-Tx Series User’s Guide Figure 125 Sample Telnet Filter 1 Enter 21 in the main menu to display Menu 21 — Filter Set Configuration. 2 Enter the index number of the filter set you want to configure (in this case 6). 3 Type a descriptive name or comment in the Edit Comments field (for example, TELNET_WAN) and press [ENTER]. 4 Press [ENTER] at the message “Press [ENTER] to confirm or [ESC] to cancel ...” to open Menu 21.6 — Filter Rules Summary. 5 Type 1 to configure the first filter rule.
Prestige 660RU-Tx Series User’s Guide Figure 126 Menu 21.6.1 Sample Filter Menu 21.6.1 - TCP/IP Filter Rule Filter #: 6,1 Filter Type= TCP/IP Filter Rule Active= Yes IP Protocol= 6 IP Source Route= No Destination: IP Addr= 0.0.0.0 IP Mask= 0.0.0.0 Port #= 23 Port # Comp= Equal Source: IP Addr= 0.0.0.0 IP Mask= 0.0.0.0 Port #= Port # Comp= Equal TCP Estab= No More= No Log= None Action Matched= Drop Action Not Matched= Forward Press ENTER to Confirm or ESC to Cancel: Figure 127 Menu 21.6.
Prestige 660RU-Tx Series User’s Guide 22.7 Applying Filters and Factory Defaults This section shows you where to apply the filter(s) after you design it (them). Sets of factory default filter rules have been configured in menu 21 (but have not been applied) to filter traffic. Table 57 Filter Sets Table FILTER SETS DESCRIPTION Input Filter Sets: Apply filters for incoming traffic. You may apply protocol or device filter rules. See earlier in this chapter for information on filters.
Prestige 660RU-Tx Series User’s Guide Figure 129 Filtering Remote Node Traffic Menu 11.5 - Remote Node Filter Input Filter Sets: protocol filters= 3 device filters= Output Filter Sets: protocol filters= 2 device filters= Call Filter Sets: Protocol filters= Device filters= Enter here to CONFIRM or ESC to CANCEL: Note that call filter sets are visible when you select PPPoA or PPPoE encapsulation.
Prestige 660RU-Tx Series User’s Guide CHAPTER 23 SNMP Configuration This chapter explains SNMP Configuration menu 22. 23.1 About SNMP Simple Network Management Protocol (SNMP) is a protocol used for exchanging management information between network devices. SNMP is a member of the TCP/IP protocol suite. Your Prestige supports SNMP agent functionality, which allows a manager station to manage and monitor the Prestige through the network.
Prestige 660RU-Tx Series User’s Guide The managed devices contain object variables/managed objects that define each piece of information to be collected about a device. Examples of variables include the number of packets received, node port status etc. A Management Information Base (MIB) is a collection of managed objects. SNMP allows a manager and agents to communicate for the purpose of accessing these objects. SNMP itself is a simple request/response protocol based on the manager/agent model.
Prestige 660RU-Tx Series User’s Guide The following table describes the SNMP configuration parameters. Table 58 Menu 22 SNMP Configuration FIELD DESCRIPTION SNMP: Get Community Type the Get Community, which is the password for the incoming Get- and GetNext requests from the management station. Set Community Type the Set community, which is the password for incoming Set requests from the management station.
Prestige 660RU-Tx Series User’s Guide The port number is its interface index under the interface group.
Prestige 660RU-Tx Series User’s Guide CHAPTER 24 System Information and Diagnosis This chapter covers the information and diagnostic tools in SMT menus 24.1 to 24.4. 24.1 Overview These tools include updates on system status, port status, log and trace capabilities and upgrades for the system software. This chapter describes how to use these tools in detail. Type 24 in the main menu to open Menu 24 – System Maintenance, as shown in the following figure.
Prestige 660RU-Tx Series User’s Guide The following table describes the fields present in Menu 24.1 — System Maintenance — Status which are read-only and meant for diagnostic purposes. Figure 133 Menu 24.1 System Maintenance : Status Menu 24.1 - System Maintenance - Status Node-Lnk 1-PPPoE 2 3 4 5 6 7 8 Status Idle N/A N/A N/A N/A N/A N/A N/A TxPkts 0 0 0 0 0 0 0 0 RxPkts 0 0 0 0 0 0 0 0 Errors 0 0 0 0 0 0 0 0 Tx B/s 0 0 0 0 0 0 0 0 03:05:59 Sat. Jan.
Prestige 660RU-Tx Series User’s Guide Table 61 Menu 24.1 System Maintenance : Status (continued) FIELD DESCRIPTION WAN This shows statistics for the WAN. Line Status This shows the current status of the xDSL line, which can be Up or Down. Upstream Speed This shows the upstream transfer rate in kbps. Downstream Speed This shows the downstream transfer rate in kbps. CPU Load This specifies the percentage of CPU utilization. 24.
Prestige 660RU-Tx Series User’s Guide Figure 135 Menu 24.2.1 System Maintenance: Information Menu 24.2.1 - System Maintenance - Information Name: Routing: IP ZyNOS F/W Version: V3.40(ST.0) | 12/16/2004 ADSL Chipset Vendor: DMT FwVer: 3.0.10.3_A_TC, HwVer: T14F7_0.+ Standard: Multi-Mode LAN Ethernet Address: 00:a0:c5:01:23:45 IP Address: 192.168.1.1 IP Mask: 255.255.255.0 DHCP: Server Press ESC or RETURN to Exit: The following table describes the fields in this menu. Table 62 Menu 24.2.
Prestige 660RU-Tx Series User’s Guide Figure 136 Menu 24.2.2 System Maintenance : Change Console Port Speed Menu 24.2.2 – System Maintenance – Change Console Port Speed Console Port Speed: 9600 Press ENTER to Confirm or ESC to Cancel: 24.4 Log and Trace There are two logging facilities in the Prestige. The first is the error logs and trace records that are stored locally. The second is the syslog facility for message logging. 24.4.
Prestige 660RU-Tx Series User’s Guide Figure 138 Sample Error and Information Messages 52 Sat Jan 01 53 Sat Jan 01 54 Sat Jan 01 55 Sat Jan 01 56 Sat Jan 01 57 Sat Jan 01 58 Sat Jan 01 59 Sat Jan 01 60 Sat Jan 01 61 Sat Jan 01 62 Sat Jan 01 63 Sat Jan 01 Clear Error Log 00:00:00 00:00:00 00:00:00 00:00:00 00:00:00 00:00:00 00:00:00 00:00:02 00:00:05 00:01:36 00:01:36 00:03:59 (y/n): 2000 2000 2000 2000 2000 2000 2000 2000 2000 2000 2000 2000 PP12 INFO PP00 INFO PP00 -WARN PP00 INFO PP00 INFO PP1c INFO PP
Prestige 660RU-Tx Series User’s Guide Table 63 Menu 24.3.2 System Maintenance : Syslog and Accounting PARAMETER DESCRIPTION Types: CDR Call Detail Record (CDR) logs all data phone line activity if set to Yes. Packet Triggered The first 48 bytes or octets and protocol type of the triggering packet is sent to the UNIX syslog server when this field is set to Yes. Filter Log No filters are logged when this field is set to No.
Prestige 660RU-Tx Series User’s Guide Figure 140 Syslog Example (continued) Jul 19 11:28:39 192.168.102.2 ZYXEL: Packet Trigger: Protocol=1, Data=4500003c100100001f010004c0a86614ca849a7b08004a5c020001006162636465666768696a6b6c 6d6e6f7071727374 Jul 19 11:28:56 192.168.102.2 ZYXEL: Packet Trigger: Protocol=1, Data=4500002c1b0140001f06b50ec0a86614ca849a7b0427001700195b3e00000000600220008cd40000 020405b4 Jul 19 11:29:06 192.168.102.
Prestige 660RU-Tx Series User’s Guide Figure 141 Menu 24.4 System Maintenance : Diagnostic Menu 24.4 - System Maintenance - Diagnostic xDSL 1. Reset xDSL System 21. Reboot System 22. Command Mode TCP/IP 12. Ping Host Enter Menu Selection Number: Host IP Address= N/A The following table describes the diagnostic tests available in menu 24.4 for and the connections. Table 64 Menu 24.4 System Maintenance Menu: Diagnostic FIELD DESCRIPTION Reset xDSL Re-initialize the xDSL link to the telephone company.
Prestige 660RU-Tx Series User’s Guide 205 Chapter 24 System Information and Diagnosis
Prestige 660RU-Tx Series User’s Guide CHAPTER 25 Firmware and Configuration File Maintenance This chapter tells you how to backup and restore your configuration file as well as upload new firmware and configuration files. 25.1 Filename Conventions The configuration file (often called the romfile or rom-0) contains the factory default settings in the menus such as password, DHCP Setup, TCP/IP Setup, etc. It arrives from ZyXEL with a “rom” filename extension.
Prestige 660RU-Tx Series User’s Guide The following table is a summary. Please note that the internal filename refers to the filename on the Prestige and the external filename refers to the filename not on the Prestige, that is, on your computer, local network or FTP site and so the name (but not the extension) may vary. After uploading new firmware, see the ZyNOS F/W Version field in Menu 24.2.1 – System Maintenance – Information to confirm that you have uploaded the correct firmware version.
Prestige 660RU-Tx Series User’s Guide Figure 142 Telnet in Menu 24.5 Menu 24.5 - System Maintenance - Backup Configuration To transfer the configuration file to your workstation, follow the procedure below: 1. Launch the FTP client on your workstation. 2. Type "open" and the IP address of your Prestige. Then type "root" and SMT password as requested. 3. Locate the 'rom-0' file. 4. Type 'get rom-0' to back up the current Prestige configuration to your workstation.
Prestige 660RU-Tx Series User’s Guide Figure 143 FTP Session Example 331 Enter PASS command Password: 230 Logged in ftp> bin 200 Type I OK ftp> get rom-0 zyxel.rom 200 Port command okay 150 Opening data connection for STOR ras 226 File received OK ftp: 16384 bytes sent in 1.10Seconds 297.89Kbytes/sec. ftp> quit 25.2.4 GUI-based FTP Clients The following table describes some of the commands that you may see in GUI-based FTP clients.
Prestige 660RU-Tx Series User’s Guide 25.2.6 Backup Configuration Using TFTP The Prestige supports the up/downloading of the firmware and the configuration file using TFTP (Trivial File Transfer Protocol) over LAN. Although TFTP should work over WAN as well, it is not recommended. To use TFTP, your computer must have both telnet and TFTP clients. To backup the configuration file, follow the procedure shown next. 1 Use telnet from your computer to connect to the Prestige and log in.
Prestige 660RU-Tx Series User’s Guide Table 67 General Commands for GUI-based TFTP Clients COMMAND DESCRIPTION Host Enter the IP address of the Prestige. 192.168.1.1 is the Prestige’s default IP address when shipped. Send/Fetch Use “Send” to upload the file to the Prestige and “Fetch” to back up the file on your computer. Local File Enter the path and name of the firmware file (*.bin extension) or configuration file (*.rom extension) on your computer.
Prestige 660RU-Tx Series User’s Guide Figure 144 Telnet into Menu 24.6 Menu 24.6 -- System Maintenance - Restore Configuration To transfer the firmware and configuration file to your workstation, follow the procedure below: 1. Launch the FTP client on your workstation. 2. Type "open" and the IP address of your Prestige. Then type "root" and SMT password as requested. 3.
Prestige 660RU-Tx Series User’s Guide 25.4 Uploading Firmware and Configuration Files This section shows you how to upload firmware and configuration files. You can upload configuration files by following the procedure in the Backup Configuration section or by following the instructions in Menu 24.7.2 – System Maintenance – Upload System Configuration File. Note: Do not interrupt the file transfer process as this may permanently damage your Prestige. 25.4.
Prestige 660RU-Tx Series User’s Guide Figure 147 Telnet Into Menu 24.7.2 System Maintenance Menu 24.7.2 - System Maintenance - Upload System Configuration File To upload the system configuration file, follow the procedure below: 1. Launch the FTP client on your workstation. 2. Type "open" and the IP address of your system. Then type "root" and SMT password as requested. 3.
Prestige 660RU-Tx Series User’s Guide 25.4.4 FTP Session Example of Firmware File Upload Figure 148 FTP Session Example of Firmware File Upload 331 Enter PASS command Password: 230 Logged in ftp> bin 200 Type I OK ftp> put firmware.bin ras 200 Port command okay 150 Opening data connection for STOR ras 226 File received OK ftp: 1103936 bytes sent in 1.10Seconds 297.89Kbytes/sec. ftp> quit More commands (found in GUI-based FTP clients) are listed earlier in this chapter.
Prestige 660RU-Tx Series User’s Guide 25.4.6 TFTP Upload Command Example The following is an example TFTP command: tftp [-i] host put firmware.bin ras where “i” specifies binary image transfer mode (use this mode when transferring binary files), “host” is the Prestige’s IP address and “put” transfers the file source on the computer (firmware.bin – name of the firmware on the computer) to the file destination on the remote host (ras - name of the firmware on the Prestige).
Prestige 660RU-Tx Series User’s Guide 217 Chapter 25 Firmware and Configuration File Maintenance
Prestige 660RU-Tx Series User’s Guide CHAPTER 26 System Maintenance This chapter leads you through SMT menus 24.8 to 24.10. 26.1 Command Interpreter Mode The Command Interpreter (CI) is a part of the main system firmware. The CI provides much of the same functionality as the SMT, while adding some low-level setup and diagnostic functions. Enter the CI from the SMT by selecting menu 24.8. See the included disk or the zyxel.com web site for more detailed information on CI commands.
Prestige 660RU-Tx Series User’s Guide 26.2 Call Control Support Call Control Support is only applicable when Encapsulation is set to PPPoE in menu 4 or menu 11.1. The budget management function allows you to set a limit on the total outgoing call time of the Prestige within certain times. When the total outgoing call time exceeds the limit, the current call will be dropped and any future outgoing calls will be blocked. To access the call control menu, select option 9 in menu 24 to go to Menu 24.
Prestige 660RU-Tx Series User’s Guide The total budget is the time limit on the accumulated time for outgoing calls to a remote node. When this limit is reached, the call will be dropped and further outgoing calls to that remote node will be blocked. After each period, the total budget is reset. The default for the total budget is 0 minutes and the period is 0 hours, meaning no budget control. You can reset the accumulated connection time in this menu by entering the index of a remote node.
Prestige 660RU-Tx Series User’s Guide Figure 154 Menu 24.10 System Maintenance: Time and Date Setting Menu 24.10 - System Maintenance - Time and Date Setting Use Time Server when Bootup= None Time Server Address= N/A Current Time: New Time (hh:mm:ss): 03 : 10 : 50 03 : 10 : 43 Current Date: New Date (yyyy-mm-dd): 2000 - 01 - 01 2000 - 01 - 01 Time Zone= GMT Daylight Saving= No Start Date (mm-dd): End Date (mm-dd): 01 - 00 01 - 00 Press ENTER to Confirm or ESC to Cancel: Table 69 Menu 24.
Prestige 660RU-Tx Series User’s Guide The Prestige resets the time in three instances: • On leaving menu 24.10 after making changes. • When the Prestige starts up, if there is a timeserver configured in menu 24.10. • 24-hour intervals after starting.
Prestige 660RU-Tx Series User’s Guide 223 Chapter 26 System Maintenance
Prestige 660RU-Tx Series User’s Guide CHAPTER 27 Remote Management This chapter covers remote management (SMT menu 24.11). 27.1 Remote Management Overview Remote management allows you to determine which services/protocols can access which Prestige interface (if any) from which computers. 27.2 Remote Management To disable remote management of a service, select Disable in the corresponding Server Access field. Enter 11 from menu 24 to display Menu 24.11 — Remote Management Control. 27.2.
Prestige 660RU-Tx Series User’s Guide Figure 155 Menu 24.11 Remote Management Control Menu 24.11 - Remote Management Control TELNET Server: Server Port = 23 Secured Client IP = 0.0.0.0 Server Access = LAN only FTP Server: Server Port = 21 Secured Client IP = 0.0.0.0 Server Access = LAN only Web Server: Server Port = 80 Secured Client IP = 0.0.0.0 Server Access = LAN only Press ENTER to Confirm or ESC to Cancel: The following table describes the fields in this menu. Table 70 Menu 24.
Prestige 660RU-Tx Series User’s Guide 27.3 Remote Management and NAT When NAT is enabled: • Use the Prestige’s WAN IP address when configuring from the WAN. • Use the Prestige’s LAN IP address when configuring from the LAN. 27.4 System Timeout There is a default system management idle timeout of five minutes (three hundred seconds). The Prestige automatically logs you out if the management session remains idle for longer than this timeout period.
Prestige 660RU-Tx Series User’s Guide 227 Chapter 27 Remote Management
Prestige 660RU-Tx Series User’s Guide CHAPTER 28 IP Policy Routing This chapter covers setting and applying policies used for IP routing. 28.1 IP Policy Routing Overview Traditionally, routing is based on the destination address only and the IAD takes the shortest path to forward a packet. IP Routing Policy (IPPR) provides a mechanism to override the default routing behavior and alter the packet forwarding based on the policy defined by the network administrator.
Prestige 660RU-Tx Series User’s Guide • routing the packet to a different gateway (and hence the outgoing interface). • setting the TOS and precedence fields in the IP header. IPPR follows the existing packet filtering facility of RAS in style and in implementation. The policies are divided into sets, where related policies are grouped together. A user defines the policies before applying them to an interface or a remote node, in the same fashion as the filters.
Prestige 660RU-Tx Series User’s Guide Figure 157 Menu 25.1 IP Routing Policy Setup Menu 25.1 - IP Routing Policy Setup # A Criteria/Action - - --------------------------------------------------------------------1 Y SA=1.1.1.1-1.1.1.1 DA=2.2.2.2-2.2.2.5 SP=20-20 DP=20-20 P=6 T=NM PR=0 |GW=192.168.1.
Prestige 660RU-Tx Series User’s Guide Figure 158 Menu 25.1.1 IP Routing Policy Menu 25.1.1 - IP Routing Policy Policy Set Name= test Active= Yes Criteria: IP Protocol = 6 Type of Service= Normal Precedence = 0 Source: addr start= 1.1.1.1 port start= 20 Destination: addr start= 2.2.2.2 port start= 20 Action= Matched Gateway addr = 192.168.1.1 Type of Service= Max Thruput Precedence = 0 Packet length= 40 Len Comp= Not Equal end= 1.1.1.1 end= 20 end= 2.2.2.
Prestige 660RU-Tx Series User’s Guide Table 72 Menu 25.1.1 IP Routing Policy (continued) FIELD DESCRIPTION Gateway addr Defines the outgoing gateway address. The gateway must be on the same subnet as the Prestige if it is on the LAN, otherwise, the gateway must be the IP address of a remote node. The default gateway is specified as 0.0.0.0. Type of Service Set the new TOS value of the outgoing packet.
Prestige 660RU-Tx Series User’s Guide Figure 159 Menu 3.2 TCP/IP and DHCP Ethernet Setup Menu 3.2 - TCP/IP and DHCP Setup DHCP Setup DHCP= Server Client IP Pool Starting Address= 192.168.1.33 Size of Client IP Pool= 32 Primary DNS Server= 0.0.0.0 Secondary DNS Server= 0.0.0.0 Remote DHCP Server= N/A TCP/IP Setup: IP Address= 192.168.1.1 IP Subnet Mask= 255.255.255.
Prestige 660RU-Tx Series User’s Guide Route 1 represents the default IP route and route 2 represents the configured IP route. Figure 161 Example of IP Policy Routing To force packets coming from clients with IP addresses of 192.168.1.33 to 192.168.1.64 to be routed to the Internet via the WAN port of the Prestige, follow the steps as shown next. 1 Create a routing policy set in menu 25. 2 Create a rule for this set in Menu 25.1.1 — IP Routing Policy as shown next.
Prestige 660RU-Tx Series User’s Guide 3 Check Menu 25.1 — IP Routing Policy Setup to see if the rule is added correctly. 4 Create another policy set in menu 25. 5 Create a rule in menu 25.1 for this set to route packets from any host (IP=0.0.0.0 means any host) with protocol TCP and port FTP access through another gateway (192.168.1.100). Figure 163 IP Routing Policy Example 2 Menu 25.1.
Prestige 660RU-Tx Series User’s Guide Figure 164 Applying IP Policies Example Menu 3.2 - TCP/IP and DHCP Ethernet Setup DHCP Setup DHCP= Server Client IP Pool Starting Address= 192.168.1.33 Size of Client IP Pool= 64 Primary DNS Server= 0.0.0.0 Secondary DNS Server= 0.0.0.0 Remote DHCP Server= N/A TCP/IP Setup: IP Address= 192.168.1.1 IP Subnet Mask= 255.255.255.
Prestige 660RU-Tx Series User’s Guide 237 Chapter 28 IP Policy Routing
Prestige 660RU-Tx Series User’s Guide CHAPTER 29 Call Scheduling Call scheduling (applicable for PPPoA or PPPoE encapsulation only) allows you to dictate when a remote node should be called and for how long. 29.1 Introduction The call scheduling feature allows the Prestige to manage a remote node and dictate when a remote node should be called and for how long. This feature is similar to the scheduler in a videocassette recorder (you can specify a time period for the VCR to record).
Prestige 660RU-Tx Series User’s Guide To setup a schedule set, select the schedule set you want to setup from menu 26 (1-12) and press [ENTER] to see Menu 26.1 — Schedule Set Setup as shown next. Figure 166 Menu 26.1 Schedule Set Setup Menu 26.
Prestige 660RU-Tx Series User’s Guide Table 73 Menu 26.1 Schedule Set Setup (continued) FIELD DESCRIPTION Action Forced On means that the connection is maintained whether or not there is a demand call on the line and will persist for the time period specified in the Duration field. Forced Down means that the connection is blocked whether or not there is a demand call on the line. Enable Dial-On-Demand means that this schedule permits a demand call on the line.
Prestige 660RU-Tx Series User’s Guide 241 Chapter 29 Call Scheduling
Prestige 660RU-Tx Series User’s Guide CHAPTER 30 Troubleshooting This chapter covers potential problems and the corresponding remedies. 30.1 Problems Starting Up the Prestige Table 74 Troubleshooting the Start-Up of Your Prestige PROBLEM CORRECTIVE ACTION None of the LEDs turn on when I turn on the Prestige. Make sure that the Prestige’s power adaptor is connected to the Prestige and plugged in to an appropriate power source. Check that the Prestige and the power source are both turned on.
Prestige 660RU-Tx Series User’s Guide 30.3 Problems with the DSL LED Table 76 Troubleshooting the DSL LED PROBLEM CORRECTIVE ACTION The DSL LED is off. Check the telephone wire and connections between the Prestige DSL port and the wall jack. Make sure that the telephone company has checked your phone line and set it up for DSL service. Reset your ADSL line to reinitialize your link to the DSLAM.
Prestige 660RU-Tx Series User’s Guide 30.6 Problems with Internet Access Table 79 Troubleshooting Internet Access PROBLEM CORRECTIVE ACTION I cannot access the Internet. Make sure the Prestige is turned on and connected to the network. If the DSL LED is off, refer to the Problems with the DSL LED section. Verify your WAN settings. Refer to the chapter on WAN setup (web configurator) or the section on Internet Access (SMT). Make sure you entered the correct user name and password.
Prestige 660RU-Tx Series User’s Guide 30.8 Problems with the Web Configurator Table 81 Troubleshooting the Web Configurator PROBLEM CORRECTIVE ACTION I cannot access the web configurator. Refer to the Quick Start Guide for hardware connections. Make sure that there is not an SMT console session running. Check that you have enabled web service access. If you have configured a secured client IP address, your computer’s IP address must match it. Refer to the chapter on remote management for details.
Prestige 660RU-Tx Series User’s Guide Appendix A Splitters and Microfilters This appendix tells you how to install a POTS splitter or a telephone microfilter. Connecting a POTS Splitter When you use the Full Rate (G.dmt) ADSL standard, you can use a POTS (Plain Old Telephone Service) splitter to separate the telephone and ADSL signals. This allows simultaneous Internet access and telephone service on the same line.
Prestige 660RU-Tx Series User’s Guide 1 Connect a phone cable from the wall jack to the single jack end of the Y- Connector. 2 Connect a cable from the double jack end of the Y-Connector to the “wall side” of the microfilter. 3 Connect another cable from the double jack end of the Y-Connector to the Prestige. 4 Connect the “phone side” of the microfilter to your telephone as shown in the following figure.
Prestige 660RU-Tx Series User’s Guide Appendix B Setting up Your Computer’s IP Address All computers must have a 10M or 100M Ethernet adapter card and TCP/IP installed. Windows 95/98/Me/NT/2000/XP, Macintosh OS 7 and later operating systems and all versions of UNIX/LINUX include the software components you need to install and use TCP/ IP on your computer. Windows 3.1 requires the purchase of a third-party TCP/IP application package.
Prestige 660RU-Tx Series User’s Guide Figure 171 WIndows 95/98/Me: Network: Configuration Installing Components The Network window Configuration tab displays a list of installed components. You need a network adapter, the TCP/IP protocol and Client for Microsoft Networks. If you need the adapter: 1 In the Network window, click Add. 2 Select Adapter and then click Add. 3 Select the manufacturer and model of your network adapter and then click OK. If you need TCP/IP: 1 In the Network window, click Add.
Prestige 660RU-Tx Series User’s Guide 3 Select Microsoft from the list of manufacturers. 4 Select Client for Microsoft Networks from the list of network clients and then click OK. 5 Restart your computer so the changes you made take effect. Configuring 1 In the Network window Configuration tab, select your network adapter's TCP/IP entry and click Properties 2 Click the IP Address tab. • • If your IP address is dynamic, select Obtain an IP address automatically.
Prestige 660RU-Tx Series User’s Guide Figure 173 Windows 95/98/Me: TCP/IP Properties: DNS Configuration 4 Click the Gateway tab. • • If you do not know your gateway’s IP address, remove previously installed gateways. If you have a gateway IP address, type it in the New gateway field and click Add. 5 Click OK to save and close the TCP/IP Properties window. 6 Click OK to close the Network window. Insert the Windows CD if prompted. 7 Turn on your Prestige and restart your computer when prompted.
Prestige 660RU-Tx Series User’s Guide Figure 174 Windows XP: Start Menu 2 For Windows XP, click Network Connections. For Windows 2000/NT, click Network and Dial-up Connections. Figure 175 Windows XP: Control Panel 3 Right-click Local Area Connection and then click Properties.
Prestige 660RU-Tx Series User’s Guide Figure 176 Windows XP: Control Panel: Network Connections: Properties 4 Select Internet Protocol (TCP/IP) (under the General tab in Win XP) and click Properties. Figure 177 Windows XP: Local Area Connection Properties 5 The Internet Protocol TCP/IP Properties window opens (the General tab in Windows XP). • 253 If you have a dynamic IP address click Obtain an IP address automatically.
Prestige 660RU-Tx Series User’s Guide • If you have a static IP address click Use the following IP Address and fill in the IP address, Subnet mask, and Default gateway fields. Click Advanced. Figure 178 Windows XP: Advanced TCP/IP Settings 6 If you do not know your gateway's IP address, remove any previously installed gateways in the IP Settings tab and click OK.
Prestige 660RU-Tx Series User’s Guide • • Click Obtain DNS server address automatically if you do not know your DNS server IP address(es). If you know your DNS server IP address(es), click Use the following DNS server addresses, and type them in the Preferred DNS server and Alternate DNS server fields. If you have previously configured DNS servers, click Advanced and then the DNS tab to order them.
Prestige 660RU-Tx Series User’s Guide Figure 180 Macintosh OS 8/9: Apple Menu 2 Select Ethernet built-in from the Connect via list. Figure 181 Macintosh OS 8/9: TCP/IP 3 For dynamically assigned settings, select Using DHCP Server from the Configure: list.
Prestige 660RU-Tx Series User’s Guide 4 For statically assigned settings, do the following: • • • • From the Configure box, select Manually. Type your IP address in the IP Address box. Type your subnet mask in the Subnet mask box. Type the IP address of your Prestige in the Router address box. 5 Close the TCP/IP Control Panel. 6 Click Save if prompted, to save changes to your configuration. 7 Turn on your Prestige and restart your computer (if prompted).
Prestige 660RU-Tx Series User’s Guide Figure 183 Macintosh OS X: Network 4 For statically assigned settings, do the following: • • • • From the Configure box, select Manually. Type your IP address in the IP Address box. Type your subnet mask in the Subnet mask box. Type the IP address of your Prestige in the Router address box. 5 Click Apply Now and close the window. 6 Turn on your Prestige and restart your computer (if prompted). Verifying Settings Check your TCP/IP properties in the Network window.
Prestige 660RU-Tx Series User’s Guide 259 Appendix B
Prestige 660RU-Tx Series User’s Guide Appendix C IP Subnetting IP Addressing Routers “route” based on the network number. The router that delivers the data packet to the correct destination host uses the host ID. IP Classes An IP address is made up of four octets (eight bits), written in dotted decimal notation, for example, 192.168.1.1. IP addresses are categorized into different classes. The class of an address depends on the value of its first octet. • Class “A” addresses have a 0 in the left most bit.
Prestige 660RU-Tx Series User’s Guide Since the first octet of a class “A” IP address must contain a “0”, the first octet of a class “A” address can have a value of 0 to 127. Similarly the first octet of a class “B” must begin with “10”, therefore the first octet of a class “B” address has a valid range of 128 to 191. The first octet of a class “C” address begins with “110”, and therefore has a range of 192 to 223.
Prestige 660RU-Tx Series User’s Guide Since the mask is always a continuous number of ones beginning from the left, followed by a continuous number of zeros for the remainder of the 32 bit mask, you can simply specify the number of ones instead of writing the value of each octet. This is usually specified by writing a “/” followed by the number of bits in the mask after the address. For example, 192.1.1.0 /25 is equivalent to saying 192.1.1.0 with mask 255.255.255.128.
Prestige 660RU-Tx Series User’s Guide Divide the network 192.168.1.0 into two separate subnets by converting one of the host ID bits of the IP address to a network number bit. The “borrowed” host ID bit can be either “0” or “1” thus giving two subnets; 192.168.1.0 with mask 255.255.255.128 and 192.168.1.128 with mask 255.255.255.128. Note: In the following charts, shaded/bolded last octet bit values indicate host ID bits “borrowed” to form network ID bits.
Prestige 660RU-Tx Series User’s Guide Example: Four Subnets The above example illustrated using a 25-bit subnet mask to divide a class “C” address space into two subnets. Similarly to divide a class “C” address into four subnets, you need to “borrow” two host ID bits to give four possible combinations of 00, 01, 10 and 11. The subnet mask is 26 bits (11111111.11111111.11111111.11000000) or 255.255.255.192.
Prestige 660RU-Tx Series User’s Guide Table 93 Subnet 4 NETWORK NUMBER LAST OCTET BIT VALUE IP Address 192.168.1. 192 IP Address (Binary) 11000000.10101000.00000001. 11000000 Subnet Mask (Binary) 11111111.11111111.11111111. 11000000 Subnet Address: 192.168.1.192 Lowest Host ID: 192.168.1.193 Broadcast Address: 192.168.1.255 Highest Host ID: 192.168.1.254 Example Eight Subnets Similarly use a 27-bit mask to create 8 subnets (001, 010, 011, 100, 101, 110).
Prestige 660RU-Tx Series User’s Guide Subnetting With Class A and Class B Networks. For class “A” and class “B” addresses the subnet mask also determines which bits are part of the network number and which are part of the host ID. A class “B” address has two host ID octets available for subnetting and a class “A” address has three host ID octets (see Table 83) available for subnetting. The following table is a summary for class “B” subnet planning. Table 96 Class B Subnet Planning Appendix C NO.
Prestige 660RU-Tx Series User’s Guide 267 Appendix C
Prestige 660RU-Tx Series User’s Guide Appendix D PPPoE PPPoE in Action An ADSL modem bridges a PPP session over Ethernet (PPP over Ethernet, RFC 2516) from your computer to an ATM PVC (Permanent Virtual Circuit) which connects to a DSL Access Concentrator where the PPP session terminates (see Figure 184). One PVC can support any number of PPP sessions from your LAN. PPPoE provides access control and billing functionality in a manner similar to dial-up services using PPP.
Prestige 660RU-Tx Series User’s Guide Figure 184 Single-Computer per Router Hardware Configuration How PPPoE Works The PPPoE driver makes the Ethernet appear as a serial link to the computer and the computer runs PPP over it, while the modem bridges the Ethernet frames to the Access Concentrator (AC). Between the AC and an ISP, the AC is acting as a L2TP (Layer 2 Tunneling Protocol) LAC (L2TP Access Concentrator) and tunnels the PPP frames to the ISP.
Prestige 660RU-Tx Series User’s Guide Appendix E Virtual Circuit Topology ATM is a connection-oriented technology, meaning that it sets up virtual circuits over which end systems communicate.
Prestige 660RU-Tx Series User’s Guide 271 Appendix E
Prestige 660RU-Tx Series User’s Guide Appendix F Command Interpreter The following describes how to use the command interpreter. Enter 24 in the main menu to bring up the system maintenance menu. Enter 8 to go to Menu 24.8 - Command Interpreter Mode. See the included disk or zyxel.com for more detailed information on these commands. Note: Use of undocumented commands or misconfiguration can damage the unit and possibly render it unusable.
Prestige 660RU-Tx Series User’s Guide 273 Appendix F
Prestige 660RU-Tx Series User’s Guide Appendix G Log Descriptions This appendix provides descriptions of example log messages. Table 97 System Maintenance Logs LOG MESSAGE DESCRIPTION Time calibration is successful The router has adjusted its time based on information from the time server. Time calibration failed The router failed to get information from the time server. WAN interface gets IP: %s A WAN interface got a new IP address from the DHCP, PPPoE, PPTP or dial-up server.
Prestige 660RU-Tx Series User’s Guide Table 98 System Error Logs LOG MESSAGE DESCRIPTION %s exceeds the max. number of session per host! This attempt to create a NAT session exceeds the maximum number of NAT session table entries allowed to be created per host. setNetBIOSFilter: calloc error The router failed to allocate memory for the NetBIOS filter settings. readNetBIOSFilter: calloc error The router failed to allocate memory for the NetBIOS filter settings. WAN connection is down.
Prestige 660RU-Tx Series User’s Guide Table 101 CDR Logs (continued) LOG MESSAGE DESCRIPTION board %d line %d channel %d, call %d, %s C02 OutCall Connected %d %s The PPPoE, PPTP or dial-up call is connected. board %d line %d channel %d, call %d, %s C02 Call Terminated The PPPoE, PPTP or dial-up call was disconnected. Table 102 PPP Logs LOG MESSAGE DESCRIPTION ppp:LCP Starting The PPP connection’s Link Control Protocol stage has started.
Prestige 660RU-Tx Series User’s Guide Table 103 ICMP Notes (continued) TYPE CODE DESCRIPTION 1 Redirect datagrams for the Host 2 Redirect datagrams for the Type of Service and Network 3 Redirect datagrams for the Type of Service and Host Echo 8 0 Echo message Time Exceeded 11 0 Time to live exceeded in transit 1 Fragment reassembly time exceeded Parameter Problem 12 0 Pointer indicates the error Timestamp 13 0 Timestamp request message Timestamp Reply 14 0 Timestamp reply message Informa
Prestige 660RU-Tx Series User’s Guide Table 105 RFC-2408 ISAKMP Payload Types (continued) Appendix G LOG DISPLAY PAYLOAD TYPE KE Key Exchange ID Identification CER Certificate CER_REQ Certificate Request HASH Hash SIG Signature NONCE Nonce NOTFY Notification DEL Delete VID Vendor ID 278
Prestige 660RU-Tx Series User’s Guide 279 Appendix G
Prestige 660RU-Tx Series User’s Guide Index A Address Assignment 57 Address mapping 82 Address Resolution Protocol (ARP) 60 ADSL, what is it? 28 ADSLstandards 30 Alternative Subnet Mask Notation 262 Any IP 31, 59 How it works 60 note 60 Any IP Setup 62 Any IP table 112 applicaions Internet access 35 AT command 207 ATM Adaptation Layer 5 (AAL5) 42 ATM layer options 151 Authentication 145 Authentication protocol 145 auto-Crossover 32 auto-negotiation 32 B Backup 207 Backup Typ 71 Bridging 145, 158 Ether Ad
Prestige 660RU-Tx Series User’s Guide Diagnostic Tools 196 DNS 134 Domain Name 57, 79 domain name 124 Domain Name System 57 DSL (Digital Subscriber Line) 28 DSL line, reinitialize 115 DSL, What Is It? 28 DSLAM (Digital Subscriber Line Access Multiplexer) 35 Dynamic DNS 32, 86, 125 dynamic DNS 32, 126 Dynamic Host Configuration Protocol 33 DYNDNS Wildcard 86 E ECHO 78 embedded help 40 Encapsulated Routing Link Protocol (ENET ENCAP) 42 Encapsulation 34, 42, 140, 143 ENET ENCAP 42 PPP over Ethernet 42 PPPoA
Prestige 660RU-Tx Series User’s Guide Interactive Applications 228 Internet Access 31, 35, 136, 139, 140 Internet access 42, 136 Internet Access Setup 162, 243 Internet access wizard setup 43 Internet Assigned Numbers AuthoritySee IANA 46 IP Address 44, 58, 78, 111, 134, 156, 160, 183, 199, 204, 230 IP Address Assignment 45 ENET ENCAP 45 PPPoA or PPPoE 45 RFC 1483 45 IP Addressing 260 IP alias 33, 136 IP Alias Setup 137 IP Classes 260 IP Filter 185 Logic Flow 184 IP mask 183 IP Packet 185 IP Policies 232 I
Prestige 660RU-Tx Series User’s Guide NNTP 79 P Packet Error 197 Received 197 Transmitted 197 Packet Triggered 202 Packets 197 PAP 145 Password 54, 118, 122, 144, 193 password 118, 244 Peak Cell Rate (PCR) 65, 68 Ping 204 Point to Point Protocol over ATM Adaptation Layer 5 (AAL5) 42 Point-to-Point 28 Point-to-Point Tunneling Protocol 79 policy-based routing 228 POP3 79 Port Numbers 78 power 242 PPP Encapsulation 152 PPP Log 203 PPP session over Ethernet (PPP over Ethernet, RFC 2516) 42 PPPoA 143 PPPoE 65,
Prestige 660RU-Tx Series User’s Guide SMT Menu Overview 119 SMTP 79 SNMP 79 Community 194 Configuration 193 Get 193 GetNext 193 Manager 192 MIBs 193 Set 193 Trap 193 Trusted Host 194 SOHO (Small Office/Home Office) 35 Source-Based Routing 228 Splitters 246 Static route 154 Static Routing Topology 154 SUA 77, 79 SUA (Single User Account) 77, 162 SUA server 78, 80 Default server set 78 SUA vs NAT 77 SUA/NAT Server Set 81 Subnet Mask 44, 58, 134, 146, 156, 199 Subnet Masks 261 Subnetting 261 Supporting Disk 2
Prestige 660RU-Tx Series User’s Guide W WAN (Wide Area Network) 64 WAN backup 70 WAN Setup 128 Web Configurator 38, 39, 40 web configurator screen summary 40 web service 245 X XMODEM protocol 207 Z Zero Configuration Internet Access 31 ZyNOS 207 ZyNOS (ZyXEL Network Operating System) 206 ZyNOS F/W Version 207 ZyXEL Limited Warranty Note 4 285
