)YARD WORKS SKU # 2641236 Model # LW0002-N 42 IN. LAWN SWEEPER A CAUTION FOR YOUR SAFETY READ THE USER MANUAL CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE OR OPERATE THE LAWN SWEEPER.
PACKAGE CONTENTS PART| DESCRIPTION QUANTITY | PART, DESCRIPTION QUANTITY A |Sweeper Housing 1 B Height Adjust Lever 1 C |Rear Hopper Tube 2 D Upper Hopper Tube 2 E clodhopper Tube 2 F Hopper Arm Tube 2 G | Pivot Rod 1 H Hopper Frame Strap 1 | Hopper Bag 1 J Support Rod 2 K |Rope 1 L Tongue 1 Customer Service Phone: {(877) 533-5558 Email:
HARDWARE CONTENTS (Shown Actual Size) 6 mmx30 mm 6 mmx16mm Qty.2 Qty. Clevis Pin Qty. 1 8mmx13 mm 8 mmx35mm Clevis Pin @ [ glistens Pin Qty. Shylock Hex Nut Qty. Cotter Pin 0 @ Shylock Hex Nut Qty. 1 Qty. 2 o R Clip Pin Qty. 6 (Not Shown Actual Size) Q@ Emuumfmmfmmuumtmmuumu ™™ ham man entrench Qty. 2 Qty. 2 SAFETY RULES . Read and understand all safety rules and operating instructions before using this equipment. . Do not allow children or untrained persons to operate this equipment. .
ASSEMBLY INSTRUCTIONS Before assembling product, ensure all parts are included. Compare parts with package and hardware contents list (page any part is missing or damaged, do not attempt to assemble the product. Contact customer service for replacement. Estimated assembly times: 15 minutes. Tools required for assembly: Open-end Wrench (included) 5= Phillips Screwdriver (not included) 1.
4. Assemble the hopper frame strap (H) to the lower hopper tubes (E) with two cross head bold (AA). Tighten with two 6 mm nylon hex nut (HH). . Insert the two upper hopper tubes (D) through the stitched sleeves on both sides of hopper bag. Slide the end of both upper hopper tubes into the rear hopper tube (C) by pressing down the spring buttons on the upper hopper tubes. . Assemble the upper hopper tubes (D) to lower hopper tubes (E) using two clevis pins (EE) and two R ¢lip pins (JJ).
8. Bend the two support rods (J} and place the end of each rod into the holes on upper and lower rear hopper tubes (C). IMPORTANT: Do not over bend the support rods . Over bending will cause the spring rods to lose supporting tension. 9. Fasten the rope (K) through the center socket on upper rear hopper tube. 10. Attach the height adjust lever (B) to the locker bar on hopper housing (A). Install two carriage bolts (BB) through the aligned holes on both height adjust lever and locker bar.
12. Attach the assembled tongue (L) to the sweeper housing (A) using two hex bolts (KK) and tighten with two 8 mm nylon hex nuts (I1). 13. Attach the assembled hopper bag to the sweeper housing. Insert the hopper arm tubes (F) into the built-in tubes on sweeper housing. Insert two clevis pins (DD) through the aligned holes and secure with two R clip Poppins. 14.
OPERATION KNOW YOUR PIVOT ROD HOPPER ARM TUBE TEETH PLATE ROPE HEIGHT ADJUST LEVI HITCH BRA FOLDING BRACKET SAFETY PIN HOPPER BAG Hopper Bag Collects grass clippings, leaves and debris. Rope Allows quick dumping of hopper bag from tractor seat. Windscreen Helps prevent collected material from being blown out of hopper bag. Hopper Arm Tubes Connects the hopper bag to the sweeper housing. Pivot Rod Allows hopper bag to tilt forward to dump material.
CARE AND MAINTENANCE . Check for any loose fasteners before each use. . Clean the sweeper after each use. a. Clean sweeper housing with a soft brush or cloth. b. Clean debris from hopper bag with a brush or broom. . Inspect for worn or damaged parts, such as brushes before each use. Replace as necessary. . Lubricate the gear mechanism once a year with light weight oil. STORAGE 1. Clean the sweeper and hopper bag to prevent rust and mildew before storage. 2.
PART| DESCRIPTION QUANTITY | PART| DESCRIPTION QUANTITY A | Sweeper Housing 1 B |HeightAdjustLever 1 C | Rear Hopper Tube 2 D grasshopper Tube 2 E | Lower Hopper Tube 2 F | Hopper Arm Tube 2 G | Pivot Rod 1 H |Hopper Frame Strap 1 | Hopper Bag 1 J | Support Rod 2 K | Rope 1 L |Tongue Cross head Bolt 2 BB |6 mmx 16 mm Carriages Pin 556 mm Clevis Pin Clevis Pin mmx 13 mm Clevis Pin 2 FF 13 mm Open-end 2 GG | Cotter Pin Shylock Nuts Shylock Hex Nut 2 JJ clipping 6 KK | 8mm x 55 mm Hex Bolt 2 TINPOT |Height Adj
