Installation Sheet

ManualsBrandsYale ManualsDoor LeversYale 5300LN Series Augusta Grade 2 Single Cylinder Keyed Entry Door Lever Set - Less Cylinder

3. Install latch.

Insert latch in door. (Be sure bevel

edge of bolt faces strike plate.)

Attach with two screws supplied.

2. Drill door.

A. Drill 2-1/8" (54mm) dia. hole thru

the door. Cut notches as shown on

template. See note. (Except

Dummy Trim)

B. Drill 1" (26mm) dia. hole in edge of

door. Mortise for latch front 1-1/8"

(29mm) wide x 2-1/4" (57mm) high

x 5/32" (4mm) deep. (Except

Dummy Trim)

C. Drill two (2) 5/16" (8mm) dia.

holes thru door. See note.

D. Drill pilot holes for latch

screws. 7/64" (2.5mm) dia.

(Except Dummy Trim)

Note: To avoid splintering wood

doors, drill holes (A) and (C) from

both sides of the door.

1. Mark door.

Mark horizontal line across edge of

door for centerline of lock at desired

installation height. Fold template over

edge of door, centering on horizontal

line. Mark centers of holes at proper

backset.

For beveled and square edge doors,

mark both sides of the door.

Note:

Be sure to verify backset before

marking & drilling door.

5300LN Grade 2 or 4700LN Grade 1

Cylindrical Lever Locksets

Installation Instructions

Door

Marker

4. Unpack lock.

Attention Installer

Installation of cylindrical locks and latches must be through

bolted in all doors. If installation instructions are not followed this

may result in damage to the lock and void the factory warranty.

Any retrofit or other field modification to a fire rated opening can

potentially impact the fire rating of the opening, and Yale Locks &

Hardware makes no representations or warranties concerning

what such impact may be in any specific situation. When

retrofitting any portion of an existing fire rated opening, or

specifying and installing a new fire-rated opening, please consult

with a code specialist or local code official (Authority Having

Jurisdiction) to ensure compliance with all applicable codes and

ratings.

Tools Required

• 2-1/8" (54mm) hole saw

• 1" (26mm) boring bit

• 5/16" (8mm) drill bit

• 7/64" (2.5mm) drill bit

• Chisel & hammer

• #2 phillips screw driver

• Handle removal tool (supplied)

• 3/8" or 1/2" drill

IMPORTANT: The accuracy of the door preparation is

critical for the proper functioning and security of this lever

handle lock. Misalignment can cause premature wear and

tear and a lessening of security.

Outside Assembly

(stays assembled)

Bushing

Inside Rose

Support Assembly

Through Bolts

Inside Lever

Handle

An ASSA ABLOY Group brand

80-9150-0060-010 (11-16)

Summary of content (4 pages)

PAGE 1
5300LN Grade 2 or 4700LN Grade 1 Cylindrical Lever Locksets Installation Instructions IMPORTANT: The accuracy of the door preparation is critical for the proper functioning and security of this lever handle lock. Misalignment can cause premature wear and tear and a lessening of security. Tools Required • 2-1/8" (54mm) hole saw • 1" (26mm) boring bit • 5/16" (8mm) drill bit • 7/64" (2.
PAGE 2
5. Adjust lock for door thickness (if necessary). (Lock is packed preadjusted for 1-3/4" (44mm) doors. Available for 2-1/4" (57mm) doors upon request.) 2-1/4" door To Adjust for Thicker Door A. Remove two (2) screws from outside rose. B. Slide outside rose away from lock body. C. Adjust rose plate to desired door thickness per illustration at right. D. Fasten outside rose to lock body with two (2) screws. 2" door 1-3/4" door C B A Slide plate to disengage 6. Install lock.
PAGE 3
Troubleshooting 1. Check door. 2. Check hinges. They should not be loose or have excessive wear on knuckles. 3. Latchbolt will not deadlock. Either strike is out of line or gap between door and jamb is too great. Realign strike or shim strike out towards flat area of latchbolt. 4. Latchbolt does not retract or extend properly. Latchbolt tail and retractor not properly positioned. A. Remove lockset. Look through 2-1/8" hole and verify latchbolt tail centered between top and bottom of hole. B.
PAGE 4
5300LN or 4700LN Cylindrical Lever Lockset Use this end of Template for Square Edge Doors Square Ed g e Door Onl y Mark Center of Door thickness for 7/8" or 1" Dia. Hole. 2-3/4" (70) Fold on Edge of Door at proper Backset Line 2-3/8" (60) B ACKSET BACK SET 5/32" x 1/8" (4mm x 3mm) Deep 2 places. Both sides of door. 2-3/4" (69.9) Between Centers 2-1/8" Dia. (54mm) Thru Door 2-3/4" (70) 2-3/8" (60) BACK SET CAUTION: IF PRINTED FROM WEBSITE, PRINT 1:1 SCALE. TO CHECK, MEASURE SCALE ACROSS.