GEOS Installation Instructions works with the Google Assistant
Please read and save these instructions before installation
GENERAL INQUIRIES FAN SUPPORT For all questions about your ceiling fan please read all included instructions, installation procedures, troubleshooting guidelines and warranty information before starting installation.
SAFETY RULES For operation, maintenance, and troubleshooting information, visit http://waclighting.com/fan-support/ To reduce the risk of electric shock, ensure electricity has been turned off at the circuit breaker before beginning. All wiring must be in accordance with the National Electrical Code “ANSI/ NFPA 70” and local electrical codes. Electrical installation should be performed by a licensed electrician. The fan must be mounted with a minimum of 7 ft. (2.
02 SAFETY RULES WARNING: Do not install or use your fan if any part(s) is/are damaged or missing. This product is designed for use only with the supplied parts and/ or accessories designated for use with this product by WAC. Substitution of parts or accessories not designated for use with this product by WAC could result in personal injury or property damage and will void the warranty. Contact an authorized dealer or the manufacturer if any parts are damaged or missing.
GET SMART This WAC Smart Fan is: Wet location-listed to the strictest Coordinate with smart devices DC UL/cUL safety regulations for voice-activated control MOTOR Wi-Fi and Bluetooth enabled Compatible with our WAC app The WAC app synchronizes seamlessly with smart home devices you already own works with the Google Assistant Available for purchase on the Google Pay and App Store more efficient than AC motor fans Wet Rated and durably finished for interior and exterior use for unlimited control
TABLE OF CONTENTS 4 Package Contents 9. Mounting Options 10. Installing the Mounting Bracket 10. 6 Attaching the Fan Blades 11. 7 Hanging the Fan 12. 7 Making the Electrical Connections 14. 8 Installing the Optional Wall Control 15. 9 Finishing the Installation 17. 10 Installing the Decorative Plate and Lower Decorative Ring 18. 11 Installing the Luminaire Module 19. 12 Controlling the Fan 21. 13 Reset 24. 14 Application 25. 15 Accessories 27. 16 Troubleshooting 29.
03 TOOLS & MATERIALS REQUIRED Phillips screwdriver Step ladder Wire cutters Electrical tape Hanging Weight: 28lbs NOTE: Before discarding packaging materials, be certain all parts have been removed. NOTE: Place the parts from the hardware bag into a small container to keep them from being lost. MAC ID IMPORTANT: Please make note of the MAC ID on the receiver and keep it in a safe place.
PACKAGE CONTENTS 04 3 2 1 Fan Blade 5 RPL-F068-60-BD-** Downrod Assembly RPL-HGR-ASM-** 5 4 Canopy Ring RPL-CAN-CYL-** Coupling Cover Motor Housing Mounting Bracket 7 Canopy RPL-CAN-CYL-** RPL-HGR-ASM-** 12 9 Luminaire Module Remote Control RC20-WT 13 A: Junction Box F4IN-120V-R1-30 RPL-F068-PARTS C: Safety Cable #10x38mm Pan Head Phillip Screws(2) Ø6.
05 MOUNTING OPTIONS INSTALLING THE MOUNTING BRACKET 1 2 Standard Ceiling Caution: Remember to disconnect the power at the circuit breaker. CAUTION: To prevent electrical shock, ensure electricity has been turned off at the circuit breaker before beginning. Figures 1 and 2 are examples of different ways to mount the space outlet box. Use A hardware if needed. 10 1. Disconnect power at the breaker. 2. Remove 1 set screw from mounting bracket and set aside for use in Finishing the Installation.
ATTACHING THE FAN BLADES 06 3 1. Slide blade into motor assembly. 2. Secure blade with blade attachment screws and washers repeat for remaining blades. Use B hardware.
07 HANGING THE FAN 4 5 1. Remove screw from hanger ball. Remove hanger ball and cross pin. 2. Loosen 2 screws, clevis pin and cotter pin. 12 1. Install coupling cover, canopy screw ring, canopy and downrod assembly into motor housing as shown.
HANGING THE FAN 07 6 1. Align downrod and motor collar holes, re-insert pins and screws. 1. 2. Slip up canopy and canopy screw cover. Re-install hanger ball with cross pin in correct place. F- 0 6 8 L 7 Seat all into the mounting bracket. Rotate until ball drops and locks into hanger bracket screw.
07 HANGING THE FAN MAKING THE ELECTRICAL CONNECTIONS 8 9 Outlet Box Hanger Ball & Downrod 1. 1. Secure the safety cable into the structure beams using the wood screw, washers, and spring washers provided. NOTE: Safety cable is required for all ceiling fan installations in Canada. Safety cable is required for ceiling fan and light (combo) installations over 35 lbs. in both flush and downrod models in the United States. 2. Slide receiver into place with the flat side facing up. Use C hardware.
INSTALLING THE OPTIONAL WALL CONTROL 08 10 NOTE: Wall control not included. A Bluetooth wall control accessory can be purchased separately. NOTE: For multi-location wiring, skip to the next step. 1. Connect the green wire marked “GROUND” from the wall control to the copper wire from the wall outletbox that feeds back to the circuit breaker – important for proper fan function. 2.
08 INSTALLING THE OPTIONAL WALL CONTROL 11 Wall Control 1 16 Wall Control 2 Wall Control 3 1. Install the wall control using the wiring diagram above. 2. Individually pair each of the wall controls with the fan receiver using the pairing instruction.
FINISHING THE INSTALLATION 09 12 13 1. Secure wire connectors with supplied wire ties. 2. Install canopy to mounting bracket with the screw removed in section 2. F- 0 6 8 L 1. Install canopy screw ring as shown.
10 INSTALLING THE LUMINAIRE PLATE AND LOWER DECORATIVE RING 14 1. Remove 1 of 3 screws from the mounting ring and loosen the others (do not remove). 15 1. Twist and lock the luminaire plate & lower decorative ring into place by following the arrows above. 2.
INSTALLING THE LUMINAIRE MODULE 17 1. Connect the white wire connectors from the luminaire module to the white wire of the fan. Follow same procedure with blue wire connectors. F- 0 6 8 L 11 18 1. Use the 3 screws located in the luminaire module screw bag to install the luminaire module to the adapter plate. Use E hardware.
11 INSTALLING THE LUMINAIRE MODULE 19 Glass Light Shade 1. 20 Install glass shade firmly without over-tightening.
CONTROLLING THE FAN 20 21 12 22 A A B Summer Mode B (Counter-Clockwise) C C Air-Gap Switch* Optional Wall Control Remote Pairing Unpairing Control Press and hold buttons for 10-15 seconds. To purge, press and hold buttons for 4 seconds. * Air-Gap Switch only included with wall control Winter Mode (Clockwise) Your fan was delivered to you with the included remote already paired to your fan. You will need to remove the pull-tab to begin using your remote control.
12 CONTROLLING THE FAN Breeze Mode Controlling Multiple Fans with Remote or Wall Controls Your remote and wall controls are capable of controlling 1. Breeze Mode mimics the natural ebb and flow of winds in nature by varying the fan speed. NOTE: Breeze Mode always rotates your fan in the Summer (CCW) direction 2. To start Breeze Mode, press and for 4 seconds. The LED will blink green and the fan will beep. 3. To exit Breeze Mode and return to standard fan mode, press and for 4 seconds.
CONTROLLING THE FAN 12 23 Fan On/Off Light On/Off Fan Direction Press and hold button for 4 seconds. Press and hold button for 4 seconds. Press and hold button for 4 seconds. Fan On/Off: Press and hold button for 4 seconds. The LED on the remote will flash green and all connected fans will beep to indicate the message has been received. All fans will turn off. This will bring all fans controlled by the remote into sync. Light On/Off: Press and hold button for 4 seconds.
13 RESET 24 25 26 WACFan_841812 Fan Wi-Fi Reset Factory Reset Receiver Factory Reset Press and hold the and for 10 seconds until LED blinks green and receiver emits 2 long beeps Press and hold buttons for 10 seconds Press the reset button on the receiver NOTE: If you change your Wi-Fi settings (SSID or Security Passphrase you will need to perform a Wi-Fi reset on the fan by holding down the fan speed up and fan speed down buttons on the remote control for 10 seconds.
APPLICATION 14 In addition to the included control, you can operate your fan with the WAC Smart Fans app*. Upgradeable with Smart Features Scan the code to the right with your phone to find out how you can enable smart features through the WAC app and integrate with your smart home ecosystem. NOTE: Press light toggle and season toggle and hold for 4 seconds if you prefer not using the app or broadcasting Wi-Fi. 1. To use the WAC app, download it from the App Store or Google Play. 2.
14 5. APPLICATION The WAC app will walk you through the main screen and show you how to create schedules, change fan speeds, dim the light, switch between Summer and Winter Modes, invite users, create groups and much more. Please refer to the WAC app instructions for more details. ** Additional purchase required to enable app control and integration. ** $9.95 + applicable tax per fan.
ACCESSORIES Product Model Description Finish Bluetooth Wall Control WC20- 6 fan speeds, dims light to 1% Works in conoutlet with WAC Smart Fan receiver (not included) WT Coupler DC- Connects two downrods Slope Ceiling Kit SC- Designed to accommodate buildings with steeper sloped ceilings up to 45° or 12/12 pitch Bluetooth Remote Control RC20- Compatible with WAC Smart Fans 6 fan speeds, dims light to 1% F- 0 6 8 L 15 WT 27
15 ACCESSORIES Product Downrod 28 Model Description DR12-** 12” downrod DR18-** 18” downrod DR24-** 24” downrod DR36-** 36” downrod DR48-** 48” downrod DR60-** 60” downrod DR72-** 72” downrod All our downrods are 1” O.D.
TROUBLESHOOTING 16 My Fan Will Not Start 1. Check main and branch circuit fuses or circuit breakers. 2. Check line wire connections to fan and switch wire connections in the switch housings. WARNING: Make sure the main power is turned off! My Fan is Noisy 1. 2. 3. 4. 5. 6. 7. Allow for 24-hour break-in period. Most noises associated with a new fan will go away during this time period. Check to make sure the screws which attached to the blades (and blade arms when applicable) are tight.
16 TROUBLESHOOTING My Fan is not producing Enough Air Movement If possible, please consider using a longer than included downrod. My remote or wall control is not controlling my fan Verify that the fan is receiving power by power cycling the fan. To do this: 1. Cut power to the fan via standard On/Off wall switch, or the breaker if standard wall switch is not applicable. 2. Wait at least 10 seconds, and then restore power. 3. The fan will power on in Pairing mode for 3 minutes. 4.
TROUBLESHOOTING 16 What is power cycling and how do I power cycle my fan? Power cycling is the act of temporaily removing the power source for your fan. If the fan is powered through a wall switch, turn the switch off for 10 seconds and back on. Alternately, you can use the circuit breaker the fan is connected to by toggling it off for 10 seconds and back on. If your fan is wired through a WAC wall control (P/N: WC20-WT) pull the Air-Gap Switch on your wall control, wait 10 seconds, and re-insert.
CERTIFICATE OF WARRANTY Felicidades por tu nueva compra. Congratulations on your new purchase. Your new WAC Smart Fan is engineered to make life easier every day. WAC creates futureforward fans and luminaires that provide energy savings and outstanding efficency. Our dedication to doing things the right way goes beyond our love for amazing products.
Félicitations pour votre nouvel achat. Votre nouveau ventilateur intelligent WAC est conçu pour vous simplifier la vie au quotidien. WAC crée des ventilateurs et des luminaires d’avant-garde qui permettent des économies d’énergie et une efficacité exceptionnelle. Notre engagement à bien faire les choses va au-delà de notre amour pour les produits étonnants.
F-068L
F- 0 6 8 L 35
F-068L waclighting.
