SURROUND SOUND HOME THEATER SYSTEM Instruction Manual Model ASR150 Please read the instruction manual carefully before using your unit. For support visit : www.1800customersupport.
GENERAL INTRODUCTION TABLE OF CONTENTS Thank you for purchasing this Surround Sound Home Theater System. Please read this instruction manual for best results. PRECAUTIONS ............................................ 2 IMPORTANT SAFETY INSTRUCTIONS ....... 3 FUNCTION CONTROL ............................... 4 Front Panel ................................................... 4 Back Panel .................................................... 4 Remote Control ............................................
PRECAUTIONS The lightning flash with an arrowhead symbol, within the equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to cause an electric shock. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN The exclamation point within the equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in this owner manual.
IMPORTANT SAFETY INSTRUCTIONS 1. 2. 3. 4. 5. 6. 6A. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. Read Instructions - All the safety and operating instructions should be read before the appliance is operated. Retain Instructions - The safety and operating instructions should be retained for future reference. Heed Warnings - All warnings on the appliance and in the operating instructions should be adhered to. Follow Instructions - All operating and use instructions should be followed.
FUNCTION CONTROL FRONT PANEL 1. SPEAKER indicators Lights when the corresponding speaker is active. 2. STANDBY/ON button Turns the unit ON, or puts the unit into STANDBY mode. 3. INPUT SOURCE button Select the sound input source to AUX, GAME or DVD. 4. SPEAKER CHANNELS button Select 2.1 channel or 5.1 channel listening mode. 5. STANDBY indicator Lights when the unit is in standby mode. 6. DVD indicator Lights when the unit is in DVD mode. 7. GAME indicator Lights when the unit is in GAME mode. 8.
FUNCTION CONTROL REMOTE CONTROL (Continued) 1. GAME button Press to select the GAME sound input source. 2. STANDBY/ON button Turns the unit ON, or puts the unit into STANDBY mode. 3. DVD button Press to select the DVD sound input source. 4. JAZZ button Press to select the JAZZ of equalization mode. 5. POP button Press to select the POP of equalization mode. 6. DOWN button Press to decrease the volume of individual speaker. 7. MUTE button Instantly turns off the sound. Press again to restore the sound. 8.
CONNECTIONS POWER CONNECTION Notes: • • • • Before you plug in the unit, make sure that the rated voltage of your unit matches your local voltage. Keep your hands dry when you are connecting the power cord to the wall outlet to avoid electric shock. When you are not going to use the unit for a long period of time, disconnect the power cord. When the player is in the standby mode, it is still consuming some power.
CONNECTIONS (Continued) POSITIONING THE SPEAKERS & SUBWOOFER CENTER SPEAKER FRONT SPEAKERS BUILT-IN SUBWOOFER REAR SPEAKERS FRONT SPEAKERS Place the front speakers on both sides of the TV, equal distances apart. CENTER SPEAKER Place the center speaker on the top of or below the TV. BUILT-IN SUBWOOFER Place the subwoofer on the floor near the TV or in any corner. REAR SPEAKERS Place the rear speakers on right beside or slightly behind your listening position, and a little higher than your ears.
CONNECTIONS (Continued) IMPORTANT : Switch off the power before connecting equipment. CONNECTION WITH TV (if your TV has Audio Output jacks) - Connect the audio cable to the white jack of AUX INPUT (L) and red jack of AUX INPUT (R) on the unit, and then connect to the corresponding AUDIO OUT jacks on your TV. This will allow your TV’s sound to play through the unit. - Press the STANDBY/ON button on the unit or on the remote control. - Press the INPUT SOURCE button until the AUX indicator lights.
CONNECTIONS (Continued) SET UP DIAGRAM IMPORTANT : Switch off the power before connecting equipment. NOTE : This system improves the sound of your DVD player, VCR or TV game, please connect the video cable directly to your TV video input jack. * One set of Audio Cable (Red & White) is supplied.
SOUND ADJUSTMENT TO ADJUST THE MASTER VOLUME - Press the VOLUME +/– button on the unit or on the remote control to adjust the volume of all speakers. TO ADJUST THE VOLUME OF INDIVIDUAL SPEAKER - Press the SOUND button on the remote control to select the speaker sound mode when the indicator will light. - Press UP or DOWN buttons on the remote control to increase or decrease the volume.
TROUBLE SHOOTING GUIDE The following checks will assist in the correction of most problems which you may encounter with your system. PROBLEMS SOLUTIONS No power. • Check that the AC power cord is connected. No sound. • Press the VOLUME + button to increase volume. • Ensure the MUTE button is not pressed on the remote control. • Ensure the INPUT SOURCE selection is correct. No sound from one channel or unbalanced left and right volume. • Check the speaker connections of the inoperative channel.
