User Guide Vax Careline: (AU) 1300 361 505 (NZ) 0800 800 900 vax.com.
Machine Overview 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 Handle Clean water tank carry handle Clean water tank release lever Clean water tank Dirty water tank release lever Dirty water tank carry handle Dirty water tank Brushbar (hidden) Pre-motor filter (hidden) Water/solution mix trigger Cord storage hook Upper cord storage Power cord Carry handle Lower cord wrap clips On/off button Recline pedal Vax carpet cleaning solution Float chamber filter (hidden) 1 10 11 12 13 2 14 3 4 5 15 6 19
General Safety Information FOR HOUSEHOLD USE ONLY. When using the carpet washer, basic safety precautions should always be observed, including the following: 1. o not leave the carpet washer unattended when plugged in. D Unplug it from socket when not in use. 2. To prevent electric shock do not use outdoors. 3. Not to be used as a toy. Children should be supervised to ensure that they do not play with the appliance. 4.
Getting Started Assembling your carpet washer Use a crosshead screwdriver. Insert handle. Insert screw. Use a screwdriver to tighten screw. Repeat on opposite side of unit. Wrap cord to store. Before you begin cleaning NOTE: Do not over saturate your carpet. • Vacuum thoroughly. •T est for colourfastness -Wet a white absorbent cloth with the solution. In a small, hidden area of your carpet, gently rub the surface with the dampened cloth.
How To Use Operating your carpet washer IMPORTANT: Only use Vax carpet cleaning solution. Using other cleaning solution may cause excess foaming and will prevent your machine from working effectively. Using other solutions will invalidate the warranty. Pour required dose of cleaning solution (approx. 40ml per 1L of water). Mix solution with warm water (max 40°C). Fill clean water tank with solution mix and re-fit the screw cap lid. Unwrap power cord and plug unit in. Recline the machine.
Looking After Your Machine WARNING: To reduce the risk of electric shock, turn the machine off and unplug from electrical outlet before performing maintenance/troubleshooting checks. Emptying the dirty water tank NOTE: Rinse out tank with clean water and leave to air dry before storing your machine. Unclip dirty water tank. Lift out the dirty water tank. Unscrew tank cap. Empty water tank. Lift out sponge filter. Rinse under water to remove debris (max 40ºC).
Looking After Your Machine Cleaning the pre-motor filter The pre-motor filter is located under the dirty water tank. Rinse under water to remove debris (max 40ºC). Allow to dry completely before replacing or storing away your machine. Removing blockages from the brushbar WARNING: To reduce the risk of electric shock, turn the machine off and unplug from electrical outlet before performing maintenance/troubleshooting checks. To locate the brushbar turn your machine upside down.
FAQ WARNING: to reduce the risk of personal injury, unplug the steamer and ensure unit has fully cooled down before performing maintenance/troubleshooting checks. Is there an accessory missing? Why won’t the cleaner pick up solution/spills? • Check the ‘Parts Overview’ page in this guide to make sure the part is definitely included in your unit. • The dirty water tan may be full and the auto shut off engaged. Empty the dirty water tank.
Other Information Service & Help Vax Careline: (AU) 1300 361 505 (NZ) 0800 800 900 Monday-Friday 8.30am to 5.00pm Any queries or concerns about using your Vax, call the Vax Careline. Calls are charged at the standard local rate. Please make a note of the serial number and model number of the steam cleaner before calling. For the nearest Service Agent, please call the Vax Careline or visit vax.com.
vax.com.
Distributed by Techtronic Industries Australia Pty. Ltd. 31 Gilby Road, Mt Waverley, VIC 3149 Australia www.vax.com.au Careline AU: 1300 361 505 www.vax.co.
