- <:: -== _. -. \ U BC9000XL T Auto Scanner I \1 11 1:1 UBZZO1248AZ OPERATING GUIDE :Ill T .
. "'-"'" '-'" U BC9000XL T Controls 2 1 3 4 II1Iden IfEE :a;t-U8CeoooXLT ' J~~~II!~!Ii!~~ ~~I.IHI.jJS I [I J r 10 9 8 7 6 1. Programming and Status Keys 6. 2. Display 3. Bank Keys 4. ON/OFFNOLUME and SQUELCH Controls 5. Rotary Tuning Controls 5 Numeric and Special Function Keys 7. Scan Keys 8. Mode Keys 9. Search Keys 10. Output Jacks. ' ..
-- --------------------- 1 Precautions Before you use this scanner, please read and observe . the following: WARNING! Uniden does not represent this unit to be waterproof. To reduce the risk of fire or electrical shock, do not expose this unit to rain or moisture. Uniden@ and Bearcat@ are registered trademarks of Uniden Corporation @1995 Uniden Corporation. All rights reserved.
[ 1 ------- I Table of Contents Introduction Included with the UBC9000XLT Feature Highlights. . . . . . . . .. Getting Started. . . . . . . . . . . .. Base Installation. . . . . . . . . .. What is Scanning? . . . . . . . .. Searching Banks and Channels. . . . . . .. Setting the Squelch. . . . . . . .. Usingthe Rotary Tuner. . . .. Programming Channels. . .. ProgrammingBy ManuaIEntry Programmingwiththe RotaryTuner ProgrammingwithSearch.. Programmingwith AUTOSTORE Deletinga Programmed Frequency. . ..
1 ..-- Introduction The UBC9000XLT is a sophisticated information radio with automatic scanning capabilities. You can use it at home as a base unit, or install in your vehicle as a mobile unit. The UBC9000XLT can store frequencies such as, police, fire/emergency, marine, air, weather, and other broadcasts into 20 banks of 25 channels each. The new Rotary Tuner feature enables rapid and easy selection of channels and frequencies. And with AUTO STORE, you can automatically program any channel.
L-.~ ...-- .- Included with the UBC9000XL T I ! 1 ,~ Australian Warranty Program Telescoping Antenna (AT124) . . AC Adaptor (AAD8500U) Read this Operating Guide thoroughly before you use the scanner. If any of the above items are missing or damaged, contact the place of purchase immediately.
r Feature Highlights . TwinTurboScan/Search - This lightning-fast technology enables the UBC9000XLT to scan up to 100 channels per second and search up to 300 steps per second (in 5kHz steps). Because the frequency coverage is so large (see "Specifications," page 53, for band listing), a very fast scanning system is essential. That is why we combined our latest - Turbo Scan and RotaryTunerControl- Turn technology . . . . . . . . . . . . . Search - into the UBC9000XL the large Rotary Tuner T.
~. f ...- . . . . . . . . Variable Frequency Steps (Increments)-In the search or Manual Mode, lets you change the steps between frequencies. Channel/Frequency Lockout-Lets you temporarily remove channels or frequencies from the scanning or search cycle. I Signal Attenuation-Reduces the scanner's sensitivity for unusually strong signals often found on the WFM (wide frequency modulation) bands.
r Getting Started h Standard 240V AC Wall Outlet DC 13.8V Jack Auxiliary Jack Antenna Jack Telescoping Antenna AC Adaptor! Charger (AAD8500U) J- Plug Off-On! Enter-Lock Switch FoldingLeg Base Installation 1. Insert the DC plug end of the AC Adaptor into the DC 13.8Vjack on the rear panel. 2. Plug the AC Adaptor into a standard 240V AC wall outlet. 3. Plug the Telescoping Antenna into the "ANT'connector. Extend the antenna to its full height.
r .-- What is Scanning? Unlike standard AM or FM radio stations, most two-way communications (listed below) do not transmit continuously. The UBC9000XL T scans programmed channels at the rate of up to 100 channels per second until it finds an active frequency. Scanning stops on an active frequency, and remains on that channel as long as the transmission continues. When the transmission ends, and no response is detected, the scanning cycle resumes until another transmission is received. ..
, ' t ,... . .....-- :t --.. ------.------....---...-..--------. ~-=:-~ CTCSS Operation This section applies only if you are installing and using an optional CTCSS Tone Board with your scanner. Installing the CTCSS Board InstallingtheCTCSSToneBoardis a simpleprocedure,and requiresonly a few minutesfollowingthe stepsbelow. CAUTION: Be sure to turn the scanner off and disconnect the power cord before attempting to open the scanner. 1. Remove the five screws from the top cover. Lift .
- r 2. Think of the Squelch Control as a gate. Turn SQUELCH fully counterclockwise. This raises the "Squelch Gate" so high that no signals can get through. SQUELCH StrongSignals @ I 3. Turn SQUELCH fully clockwise until you hear a hiss. This lowers the "Squelch Gate" so that everything gets through... noise, weak signals, and strong signals. SQUELCH .. . Strong Signals .. .. MediumSignals ,. -WeakSignals----..-----....-......... ---..--- ..---..---..---..--.. Noise---..---..---.. ---..--.. ---..
r Using the Rotary Tuner Frequency LED Channel LED Mode Selector Rotary Tuner Lock LED Lock Key Rotary Tuner and Controls This unique feature allows easy, rapid, and precise selection of frequencies and channels in the UBC9000XLT. Frequency/Channel Mode Selector - Press to switch between channel or frequency mode. When the CHAN LED is on, you can step rapidly through channels with the Rotary Tuner. When the FREQ LED is on, you can tune quickly and accurately through frequencies with the Rotary Tuner.
'} --- Programming Channels Before you can scan, you must program the channels within a bank. You can store one frequency per channel, up to 500 channels.
'} Programming By Manual Entry Use these keys: I81Iden" EJEl8 C] D (PROGIlSENOIIAlPHA) ~~ ~ . c::s ~ uo @ @ c::> \ J (DB.AY.) p.IJI!C~T CL][[J m:J ~ [L) CD ID (E] [IJ CL> -. .- @ CJ DATA ~ c:::3> JJ fl) Scan and Numeric Keys 1. Select a frequency. Example: Program 482.7625 MHzinto Channel1. 2. Press I MANUAL) Manual to enter the Bank A ch 22 LlO OOO.OOOOMHz Mode. 3. Enter the channel number, then press Bank A P ch 1 LlO OOO.OOOOMHz I MANUAL). 4. Enter the frequency.
r ..- If an error is made during programming, or if the frequency is out of range, this screen appears. Enter a valid channel or frequency number. 1 Bank A P ch OUTOFBAND If the frequency is stored in another channel, the display will indicate the original channel for that frequency. Bank A ch 1 DUPLICATECH230 To program more channels, repeat steps 3 and 4. Press ~ to store the same frequency into the selected channel. Or, select another channel. Or, press ~ twice to clear.
f ~ ..---- 3. Select a frequency. Example: 123.7750 4. Enter the Frequency. Then press ~ . Bank C ch 52 123.7750MHz 5. To turn to a new frequency, select FREQ withthe Rotary Tuner Mode Selector then turn rightto step up, leftto step down. Example: 123.7875 (turn right) 12.5KHz ch :::'?2 AM 123.7875IvrHl- Note: The channel indicatorflashes on the display, indicatingthat the frequency displayed is not programmed in that channel. 6. Press ~ channel. to program the Bank C ch 52 123.
r 1. Select a frequency range. See page 53. Example: 450.000MHz to 456.000 MHz 2. Press I . MANUAL) 3. Enter the frequency and press ~to enter the lower limit of the search range. Example: 450.000 MHz NFM 450o0000MHZ! I 4. Enter the frequency and press ~to enter the upper limit of the search range. Example: 456.000 MHz 5. Press~ function. NFM 450.0000MHz NFM 456.0000MHz to begin the search To exit search, press . I MANUAL) SRC NFM 12 .5 KHz t 450.
t '} 1. Press I Ito enter the Transfer Mode. SEI\O 2. Enter Bank or ch 450.3875MHz Enter the channel number. Example: Channel 200. 200 450.3875MHz] I 3. Press~. Bank H ch200 OOO.OOOOMHz 0 I 4. Press~ to Program the frequency. (Displayflip-flops) 450.3875MHz I Bank H ch200 450.3875MHz 6c. Programthe frequency intothe first open channelof another bank. 1. Press I SEI\O I to enter the Transfer Mode. 12.5KHz ch'NFM 450.3875MHz 2. Choose a bank. Example: Press [C] . Enter Bank or ch 450.
j r 1 ------- Programming With AUTO STORE This procedure searches a frequency range and automatically stores active'requencies into empty channels of the selected bank(s). Note: Be sure to set SQUELCH before you begin a search. See "Setting the Squelch" on page 8. Use these keys: :@ .. l7$. LH EXTSI' @ @ YO Programming, Search, Scan, Mode, Numeric, and Bank Keys and Rotary Tuning Controls I 1. Select a frequency range. See page 53. Example: 810.000 MHz to 856.000 MHz 2. Press I MANUAL). 3.
t .--- l' 5. Press [ AUTO I to enter the Auto Bank - ABCDEFOHU-1234567890- Store Mode. 6. Select the bank(s) for programming. The selected bank indicator(s) stop blinking. Example: Press ~ and Bank -=ABCDEFOHU-12~4?pZ~90- ~. 7. Press[ SRC] to begin the Auto Store. The LED on the flashes. [AUTO I key Note: You hear no audio during Auto Store. Note: If the bank you chose is already fully programmed, a double beep sounds. Choose another bank. Searching frequencies Storing an active frequency.
, r t "--" Deleting a Programmed Frequency Use this procedure when you want to delete a frequency from a channel without storing a new frequency in its place. .~ Use these keys: EIfiI @ 1I11den """"""""UBC8000XLT (] CD [[J lE:] [[] [0 CD @:] [[] [D ~ SQUELCH Programming, Search, Scan, Numeric Keys, and-Rotary Tuning Controls 1. Enter the channel number. 2. Press ~ . 3. Press~ . Bank D ch 86 854.8625MHz Bank D LlO ch 86 OOO.
f l' 3a. To select the transfer channel, press I SEND I ... Enter Bank or ch 855.9125MHz 3b. Then enter the channel number... 855.9125MH~ ] [ 3c.Thenpress~. Bank A ch 8 OOO.OOOOMHz D (Display flip-flops) Bank D ch 83 855.9125MHz 4. Press~ to transfer the Bank A ch 8 855.9125MHz frequency. Programming Channels with Alpha Characters Use this feature to name programmed channels (up to 250 channels) for easy reference. Example: Channel 1, Local Police.
t ---1. Press --- (PROG , ' I... 1 '-- Select ALPHAorcrcss Then press I ALPHA). Select chan from 2. Enter the channel number... Note: You must select a programmed channel. Example: Channel 1 Then press ~. I ~\ID: 1 to 50'(1)\ from 1 to soJI The Alpha Edit Screen appears. ~O& 3. Turn the Rotary Tuner left/right to choose a letter from the upper line of characters. Example: "L" Press~ characters, letters.
t '- 1: - '--..--- To Delete Alpha Characters Use these keys: 1I1IIBI P uec--. T CD [[J ID m:J[L) CD ID [E] IIJ £I:) ~i!~...i...!,ij~]~ \...~...!~~~.u.~..~. SQUElCH @ SlJ Program, Search, Scan, Mode, Numeric Keys, and Rotary Tuning Controls 1. Press I . MANUAL) 2. Press( PROG I.... Then press I Select ALPHAor CTCSS ALPHA). . ,~ Select ~8t from chan 1 to :>0'(1)\ 3. Enter the channel number with the alpha characters you want to delete, then press ~. I 4.
1 L--------7. Press~ to storethe changes. [Bank A ch 1] Select chan \It::1~ from 1 to sod) 8 Press ( SCAN Mode. I, IMANUAL), or ( PROG Ito exitthe ProgramAlpha I 23 - =- ..", .
~- The Scan Mode Scanning All Programmed Channels and Banks Use these keys: ~. R ~~~ C] (PROGIlSENOIIAlPHA) D[1iiI! ffiEO. ~\\; . C>
t --'~-'- :t . --....-.- Turning Banks ON or OFF After you have programmed channels in several of the scanner's banks you can customize which channels you scan by turning the banks on or off. 1. Press ( SCAN I. . \ I/ ean~ ABCeEFGHIJ -}:S/C~r: 123lJ567890 2. To turn a Bank OF ~ letter or numb er. F, press the Example: ~. ~ ~ ~ ~ ' ~G ~,~ f"8""l . d_~_.J ~ anK- S I,!KJ. IT] ,can~ . @::J : 3. To turn a Bank ON, press the number or letter again. Example:~ ,[I] ,~. ABCD~\FI~ -1 .
r Locking Out Channels The lock-out feature lets you further customize the channels that you want to scan at a particular time. For example, .if a stored frequency broadcasts almost all the time, the scanner will stop on it and stay. You can lock out that channel when you are more interested in the other channels for the current scanning session. When you lock out a channel, it is temporarily excluded from scanning, but it remains programmed so that you can easily unlock it for scanning later.
-- 1 ..---------- Unlocking a Channel 1. Press IMANUAL) . 2. Enter the channel or press the Channel Mode Selector and use the Rotary Tuner to find the channel you want to unlock. 3. Press ( 1)0 ). Bank A P ch 1 LlO 482.7625MHz BankA P ch 1 482.7625MHz -' 4. Press (SCANI to resume scanning. Unlocking All Channels in selected Scan Banks. 1. Press I MANUAL) . 2. Press and hold ( Bank D ch 53 450.3875MHz 1)0 ). You hear a double beep when all channels are unlocked, except OOO.OOOOMHz.
'1. ' Using Priority Scan You can program one Priority Channel in each of the first 10 banks. During Priority Scanning, your scanner checks these special channels every two seconds, whether or not the scanner has located an active channel. Use these keys: ~. ~B~ II1Iden"-""""~UBC--T
:L-The Search Mode In the Search Mode, the scanner looks for any active frequencies within a range of frequencies you select. It is best to select a narrow range, so that you have a better chance of finding all the active channels. Use Search if you don't have a frequency directory handy, or if new stations have been added since the directory was published. Use these keys: MEM ( 0\Mr mlden a SHFT 1 1 AlJX 11 STArus > (~II~II-J D [ .)( . .. . .. . .
.....--- t_- ""., '1 . Scrolling Frequencies During a Search Scrolling temporarily suspends a search and allows you to manually move up or down through the frequencies. Use these keys: m1IdenD (~][:~~ 8 ( PROO 11 SEND 11 ALPHA ) .,.,.,.,."., (. §lWN SCAN uec~T CD IEJ [[J [[J [[:) CD rn::JlE] IIJ Iz:) C] TUAIO 11 MAN.JAL BA .) CIM ' @ OFf' CD [!::)(i:J AM WFM (L) (LJ- (i:] .- 12.' 2...... ..~. ~~=.~~D::~ @ @ ~ [i:::)(!:J oa
1 Using Turbo Search Turbo Search increases the search speed from 100 frequencies per second to 300 frequencies per second in ranges where the frequencies are spaced 5 kHz apart. Use these keys: ME" ( CX>I.M I SHFT ~ I STATUS) mIIdI!na J) (] (PROOIlsec>IIALPHA) ~ ER I - SRC J( AUTO ~I -I UNE EXTSI' @ @ (eOOAN , , "'" OFf' CD AM C!:J(D -.. ~ C!:JILJ - 12.' - ..rz:::J C!:J ILl CUI- +-usc-..r
:t .---- Locking Out Frequencies This feature is similar to locking out a programmed channel, except you can only lock out 50 frequencies. Use these keys: ~~~ ( II1lden "_i ~!, PAOQ """"."""UBC8000XLT CD [I:J ID [Q:][I:) CD @:][ID ITI IT:) CJ 11SEND 11ALPHA) Search, Mode, Numeric Keys, and Rotary Tuning Controls While searching press ( uo )when the scanner stops on an undesired frequency. Search resumes immediately. Unlocking a Frequency 1. Press~ to stop the search. 2.
f t 'I.. Unlocking All Frequencies 1. Press~ to stopthe search. 2. Findany locked-outfrequency. 5 . OKHz C~3 LID 47.2250MHz 3. Press and hold ( uo )for two seconds. You hear a double beep when all frequencies are unlocked. Birdies Birdies are internally generated frequencies that cause the scanner to stop during search. If you have problems with these frequencies, use the lockout features to keep the scanner from stopping. Birdie Frequencies in MHz 32.000 428.5875 74.200 431.9875 128.000 443.
f ~.. ..----... Additional Scanner Features -- Use these keys: II1ld1!1a."""""UBC8000X1.T D -CJ UNE EXTSP @ @ (. §T'MN SCAN TUAfIO 11 MANUAL .) ~
Changing the Frequency \ \ I Step The frequency step is the minimum space between frequencies in the Manual or Search Mode. Your scanner is pre-programmed with a default frequency step for each of its frequency bands. You can override the default frequency step to search in larger or smaller increments when searching, during Auto Store, or when stepping through frequencies with ~, ~ or the Rotary Tuner. 1. Press~ search. \ Ii ! I I I I I i ! i to stop the I\ I 2. Press I SHIFT). \ ! 3.
c ,,- ___,m- ---,._- """,___O' "--' mm,__-, , m +-, Setting the Signal Mode Your scanner is capable of receiving three signal modes: AM Amplitude Modulation NFM Narrow Frequency Modulation WFM Wide Frequency Modulation Each of the scanner's frequency bands is pre-programmed with a default signal mode. If you want to override the default signal mode for a particular frequency, use these keys: IIlIden .""'.""""U~T ,""}'MiiM',""'","',"""""""','""""",,,~,','i,' ra.
~ -. I Using Signal Attenuation When the ATT LED is on, the incoming signal strength is attenuated (reduced) by about 15 dB. This prevents unusually strong signals from over-loading the scanner. In the Scan Mode, you must individually program each channel you want to use the Signal Attenuation feature. You can use the Signal Attenuation feature in the Manual, Search, or Scan Mode. Use these keys: ~.
Preventing Accidental Programming The UBC9000XLT has a lockfeature to prevent accidental programming , ( PROG I, entries. To disable the ~ I I, and [ I keys, move the rear SEND OFF ON ffIEij a:==::D AUTO panel switch to ON. IX When you press ~ , ( PROG I, or [AUTO I , a message appears. 1 SEND I, ENTER LOCKa:==::D Bank C ch 69 ENTERLOCKED Using COUNT to Monitor Channel Activity The Count feature counts the number of times scanning stops on an active channel.
f . -..t- 3. Press IMANUAL), ~, ~ the count for each channel. or use the RotaryTuner to see I Counter counts up to 99. To reset the counter for individualchannels 1. Press I MANUAL). 2. Enter the channel number or use ~, ~, or the Rotary Tuner to select the channel. 3. Press ~ Count:01P ch 1 482.7625MHz twice. Count:OOPch 1 482.7625MHz Note: Turning off power resets the counter for all channels. To turn COUNT off: Press (COUNT I. Bank A P ch 1 482.7625MHz 39 '--'-- -- .--.--.
Displaying Bank MemoryStatus This feature shows the programming status of the channels in a bank. Use these keys: I81IdI!n.............. uec~T ~}"~"":"tt""t'""""""?"~,,,,,:: li~;;;~;;.; ~~ ~ @ @ D . .' '........... '.'i"",,"""'{' . . ., UO "---J c:::> ~ c:::> (DElAY.) c:::!> DATA ~ ;;;!~~I~t~~~ Status, Scan, and Numeric Keys, and Rotary Tuning Controls 1. Press I MANUAL) . 2. Enter the channel number or Bank E ch 110 854.9800MHz use the Rotary Tuner to select any channel in the bank.
~ , l ,-......-...........--- - I I ( Using Auto Recording The Auto Recording feature allows you to automatically tape record activity from any channel of your scanner. When scanning stops on the assigned channel, the recorder records the broadcast. 1 ! I ! 1 ! Before using the Auto Tape feature, connect the scanner to a tape recorder. (See page 6.
'-t~ When scanning stops on a channel that displays "Record", the channel will automatically be recorded. To deselect a channel so that it is not recorded: 1. Display the assigned channel on your screen. Record ch 1 482.7625MHz 2. Press~. Bank A P ch 1 482.7625MHz "Record" disappears on the display to indicate that channel will not be recorded. Viewing Scanner Status Information This feature lets you quickly review the settings for several features of the UBC9000XLT.
1 "1' Bank C ch 72 CTCSS:OFF000.0 Bank C ch 72 I HI-CUT:OFF Bank C ch 72 RECORD :OFF Bank C ch 72 DIMMER: BRIGHT In Search Mode: 1. Press ~to stop the search. 2. Press and hold I STATUS) for two ~ 5 .0KHz ch~O~ MODE:NFM '/1" seconds. You hear two beeps, then the status information scrolls across the display. ~/ 5.0KHz ch /)I~+HI-CUT:OFF 5.0KHz C~1 DIMMER:BRIGHt/l\ 5 .
Use these keys for Display Light and Hi-Cut f""~'""""~','",'"""""",'"",'",,,"~",""f iii~lltli ~ I . SAC 11 AUTO .1 ~LINE EXT SP @ @ (] (. §T\\1N D [ T1.IWO CD m::J@:J[[] [D CD [D [E] [[] [L) ~::.:) ~ ilSla SCAN 11 MANUAL .) PR T\JRI!O cress DATA c::;J c;;> unIdI!n "-"-""~T ( An.) c:=> c::!> c::!> Status and Special Function Keys Display Light The Display Light has three settings: BRIGHT, DIM, and OFF. 1. Press I SHIFT). 2. Press the setting. Example: Press 8 \17 .
'-i- CTCSS Operation This section applies only if you are installing and using an optional CTCSS Tone Board with your scanner. Installing I the CTCSS Board Installing the CTCSS Tone Board is a simple procedure, and requires only a few minutes following the steps below. . I CAUTION: Be sure to turn the scanner off and disconnect the power cord before attempting to open the scanner. 1. Remove the five screws from the top cover. Lift .~ ~- :.elf- - ~ @ ~ ~ fim~ :5<0) ~ 2.
'1- 4. Align the pins on the CTCSS Board with the sockets on the mother board. Make sure they go straight into the sockets. The 4 pin socket is toward the front of the scanner. The 3 pin socket is toward the back of the scanner. CTCSS Board installed To speaker (Inside Top Cover) 0 D ;-- ~O 0000 cO [J:::::E QJ 3 pins 5. Gently push straight down on the CTCSS Board until the pins are fully seated in the sockets. I I \ , , I i .. II D fo I I I I 6.
"'1' [ I Using CTCSS The CTCSS (Continuous Tone Control Squelch System) feature allows squelch to be broken during scanning only when a CTCSS Tone is received. I II I To program a channel for CTCSS, use these keys: II1lden.""""""'Uec_XLT
\ I / ... \' I " 6. Use the Rotary Tuner to select a tone frequency. (See page 49 for a list of tone frequencies.) 7. Press ~ to program the frequency. - 67 -: OHz " / I\... ch 72 854.2875MHz ... \' I " -- 67 -: OHz -ch 72 " / I\... 854.2875I'V1F+z - After programing the frequency, the scanner returns to step three. Continue programming CTCSS frequencies, or press IMANUAL) to exit. Select chan from 1 to ?fJ SIde To Change the CTCSS Tone Frequency 1. Press I . MANUAL) 2.
7. Use the Rotary Tuner to select a new frequency. (See below for a list of CTCSS tone frequencies.) 8. Press~ '- "' I " -- . -- 77 . OHz - -ch -- / After programming the frequency, the scanner returns to step four. Continue programming CTCSS frequencies, or press / r-77 . OHzch 72 -- / I 854.2875MHz 72 I 854.287~~Jfz Select chan ?J from 1 to SlOo I MANUAL) to exit. Note: To remove a CTCSS Tone Frequency, from a channel, program the frequency as " 00.0 " CTCSS Tone Frequencies 000.0 ==> 67.
Care and Mai ntenance General Use Write down the programmed channels/frequencies in case of a memory loss. Firmly press each scanner key so that you hear the entry tone. Location If strong interference or electrical noise is received, move the scanner. Also, a higher antenna ,location usually results in better reception. Do not use the scanner in high-moisture environments, such as a kitchen or bathroom. Avoid placing the scanner in direct sunlight or near heating elements or vents.
c. ~ Troubleshooting If your UBC9000XL T is not performing properly, try the steps listed below. PROBLEM Scanner won't work. SUGGESTION Check the connections at both ends of the AC Adaptor. Tum on the wall switch of your room. Move the AC Adaptor to another wall outlet. Make sure the power switch is tumed on. Poor reception. Check the antenna and its connection. You may be in a fringe area. This may require an optional multi-band antenna. Check with your dealer or local electronics store.
r Optional Accessories and Replacement Parts AC Adaptor (AAD 8500U) Telescoping Antenna (AT124) ~ External Speaker (ESP25, SQ) Mobile Mounting Bracket Assembly Kit (MBOO1) .0=0 o~ = 0=0 = 0=0 &?qIb ~ Hard Wire Cord (PSOO2) CTCSS Board (BCOO5) ~ 52 -- .
r Specifications Banks: Total 20 banks Channels: 500 channels Search Band: Total 16 Search bands(AM, NFM, WFM) Frequency Range: Frequency Coverage (MHz) 25.0000 28.9950 29.0000 - 55.9950 56.0000 - 69.9500 70.0000 - 87.9950 88.0000 - 107.9500 108.0000 - 136.9875 137.0000 - 173.9950 174.0000 - 221.9500 222.0000 - 399.9875 400.0000 - 519.9875 520.0000 - 549.9500 760.0000 - 823.9875 824.0100 - 848.9700 849.0000 - 868.9875 869.0100 - 893.9700 894.0000 - 1300.
- ~..... Warranty Uniden UBC9000XLT Auto Scanner Australian 1 Year Warranty Note: Please WARRANTOR: keep your sales docket as it provides evidence of warranty. Uniden Australia Pty. Limited ACN 001 865498 ELEMENTS OF WARRANTY: Uniden warrants to the original retail owner for the duration of this warranty, its UBC9000XL T Auto Scanner (hereinafter referred to as the product), to be free from defects in materials and craftsmanship with only the limitations or exclusions set out below.
-=== ;: ..". . unl I!n@ @1995 Uniden Australia Pty. Limited. All rights reserved.
