App Cam Solo 4G 2K Quick Start Guide
What’s in the Box App Cam Solo 4G 2K x1 Micro USB Cable x1 Rechargeable Battery x1 Outdoor Security Mount x1 Mounting Hole Template x1 Mounting Strap x1 Silicone Weatherproof Cover x1 Screw Kit x1 Reset Needle x1 The camera and the rechargeable battery are packed separately in the same package. Please dress the camera with the Silicone Cover for better weatherproof performance when you install the camera outdoors.
General Introduction Built-in Mic Infrared Lights Daylight Sensor Lens Status LED Built-in PIR Sensor Speaker Micro USB Port Micro SD Card Slot SIM Card Slot Reset Hole *Press the Reset button with a Pin to restore factory settings.
Install the SIM Card and Battery 1. Rotate the back cover counterclockwise, insert the SIM card into the slot. 2. Insert the battery into the camera and tighten the back cover. • Tips for SIM Card SIM card requirements: • The SIM card should supports WCDMA and LTE networks. • Activate the card through your smartphone or your operator before inserting it into the camera. • Some SIM cards have a PIN code, please use your smartphone to disable the PIN first before insert the sim card to the camera.
Register Online (Camera Initial Setup) 2. A blue LED will flash for some seconds and then go solid before going out, you would hear “Network connection succeeded”, which means the camera has been successfully connected to the network. 1. After the SIM card and battery are installed, a red light will be on, and you will hear the voice prompt “Camera is starting up, please wait”. The red LED will be solid on for some seconds and go off.
Note: You may also run into the below situations: Voice Prompt 1 “SIM card cannot be recognized!” 2 “The SIM card is locked with a PIN. Please disable it” 3 “Not registered on network. Please activate your sim car d and check the signal Strength” 4 “Network Connection failed” 5 “Data call failed. Please confirm your cellular data plan is available or import the APN settings” LED Status Camera Status Solution Camera cannot recognise this SIM card 1.
Setup Camera on Uniden Solo App There are two ways to get the Uniden Solo App: • Search “Uniden Solo” in App Store (for iOS), download and install the app. • Search “Uniden Solo” in Google Play (for Android), download and install the app. 12:00 1. Please click the “ ” button in the top right corner to add the camera. 2. Scan the QR code on the side of the camera and follow the steps to complete the setup.
3.
Attention for Camera Installation • PIR Sensor Detecting Distance The PIR senor has 3 sensitivity levels for your adjustment: Low/Mid/High. Higher sensitivity offers longer detecting distance. The default sensitivity of the PIR sensor is at “High”.
! Important Notes for Reducing False Alarms For reducing false alarms, please note that: • • • • • • Do not install the camera facing any objects with bright lights, including sunshine, bright lamplights, etc. Do not place the camera too close to a place where there are frequently moving vehicles. The recommended distance between the camera and the vehicle is 15 meters Stay away from the outlets, including the air conditioner vents, humidifier outlets, the heat transfer vent of projectors, etc.
Cover the Monitoring Area When installing the camera, please install the camera angularly (the angle between the sensor and the detected object is larger than 10°) for effective motion detection. If the moving object approaches the PIR sensor vertically, the sensor may not detect the motion events.
Charge the Battery It is recommended to full charged the camera before mounting the camera outdoors. There are three ways you can charge the battery: 1. Charge the battery when it's installed to the camera. 2. Charge the battery separately. 3. Charge the camera with the compatible solar panel (SPS-02). * Please note that the USB charger and Solar Panel are NOT included in the package. You can buy the solar panel on separately.
! Important Safeguards on Rechargeable Battery Use App Cam Solo 4G 2K is not designed for 24/7 full capacity running or around-the-clock live streaming. It’s designed to record motion events and remotely view live streaming only when you need it. 1. Please charge the rechargeable battery with a standard and high-quality DC 5V or 9V battery charger. 2. If you want to power the battery via the solar panel, please note that the battery is ONLY compatible with SPS-01 solar panel.
How to Mount the Camera Drill holes in accordance with a mounting hole template and screw the security mount into the wall. If you are mounting the camera on any hard surface, insert plastic anchors into the holes first. 1 2 Install the camera on the security mount. 3 4 To get the best field of view, loosen the adjustment knob on security mount and turn the camera. Stiffen the adjustment knob to secure the camera in place.
Ba ck How to Attach the Camera to a Tree 1 Thread the provided strap to the mounting plate. 2 3 Attach the plate to the security mount with the smaller screws. Install the camera and adjust the camera angles as instructed in step 2 & 4 in the previous installation guide. 4 15 Fasten the security mount to a tree.
Specification Model Image Sensor Display Resolution Angle of View PIR Detecting Distance Hardware Features 1/3” CMOS Image Sensor 2560 x 1440 (4.
Frequency Bands B1/B5(AUV)@WCDMA, B1/B3/B5/B7/B28@LTE 3G/4G Transmission Data HSPA+: Max 14.4Mbps (DL)/Max 5.76Mbps (UL), LTE CAT1: Max 10Mbps (DL)/Max 5Mbps (UL) Type Specification Lithium battery/3.
WARRANTY Uniden App Cam Solo 4G 2K Important: Satisfactory evidence of the original purchase is required for warranty service. Please refer to our Uniden website for any details or warranty durations offered in addition to those contained below. Warrantor: The warrantor is Uniden Australia Pty Limited ABN 58 001 865 498 (“Uniden Aust”).
Parts Covered: This warranty covers the Product and included accessories. User-generated Data: This warranty does not cover any claimed loss of or damage to user-generated data (including but without limitation phone numbers, addresses and images)that may be stored on your Product. Statement of Remedy: If the Product is found not to conform to this warranty as stated above, the Warrantor, at its discretion, will either repair the defect or replace the Product without any charge for parts or service.
THANK YOU FOR BUYING A UNIDEN PRODUCT © 2022 Uniden Australia Pty Limited V1.
