MOWRO RM18 Operation Manual ! this manual. Failure to follow this important safety information may result in serious injury. Carefully read and understand the manual completely before attempting to operate the MowRo.
For Service or Questions Call 1-800-976-3009 www.mowro.
Table of Contents Important Safety Information ................................................................. 4 Warranty Information ............................................................................. 7 Mower Part and Overview ..................................................................... 8 Planning and Layout Guide .................................................................... 10 Docking Station Installation .................................................................
Important Safety Information ! WARNING WARNING: Read and thoroughly understand all instructions and safety information before assembling or operating the MowRo Lawn Mower. Failure to do so may cause serious injury. Do not allow anyone to operate this MowRo Lawn Mower who has not read this manual. As with all power equipment, the MowRo can be dangerous if assembled or used improperly. Do not operate this mower if you have doubts or questions concerning safe operation.
Important Safety Information General Safety Failure to follow warnings, cautions, assembly and operation instructions in the Operation Manual may result in serious injury. ! DANGER READ THE OPERATION MANUAL BEFORE OPERATION. • Do not permit children to operate this equipment at any time. • Do not permit others that have not read and understood the complete Operation Manual to operate this equipment. • Keep all people and pets a minimum of 10 feet away from the work area.
Important Safety Information Safety Icons Safety icons are to remind you of important information while you are operating the unit. ! The MowRo has sharp blades. Use caution when operating around other people and pets. Use caution when operating this power equipment. Read and understand the Operation Manual before operating the MowRo Lawn Mower. Keep your hands and feet away from the rotating blades. Use extreme caution when lifting and transporting. Wear gloves to handle the blades or blade disc.
IMPORTANT NOTICE Redback warranties this product, to the original purchaser with proof of purchase, for a period of two (2) years against defects in materials, parts or workmanship. Redback, at its own discretion, will repair or replace any and all parts found to be defective, through normal use. This warranty is valid for only units that have been used for personal use, and that has been maintained in accordance with the instructions in the owner’s manual.
Overview PIN Code Area Clock Start Time Rain Sensor On / Off switch Battery capacity Setting Start Confirm Return to charging station Emergency stop Charging electrode Cutting height adjustment Handle Rear wheel Front wheel Chasis protection 8
6 pegs for the charging station 100m boundary line 150 boundary line pegs 100m boundary line 2 Wire Clamps 4 Wire Splicers 9 spare blades with screws LED Green blinking, charging.
Planning and Laying the Boundary Line Laying Boundary Lines In order to make the Robot Mower mow within the desired area – and only that area – you need to mark the area by means of boundary wiring. Remove all foreign objects, rocks, roots, etc. that may interfere with the Robot Mower’s operation in the mowing area. Large objects such as trees, swings sets, ponds, etc. should be encircled by the boundary line. The boundary wire line needs to be laid out in a continuous line (see Figure 2 on following page).
Ensure this side of docking station is facing inward to the lawn.
Docking Station Installation Avoid placing the docking station in a corner of the lawn or in low-lying areas where the docking station or the Robot Mower may be damaged by puddles, or under a high tree due to the risk of lightning. Note: It is important that the adapter and the electrical plug are always kept dry! The docking station must have 6.5 feet of free space in front of it so the Robot Mower can return to charge or when mowing is complete (see Figure 3).
Operation PIN Code Clock Mow Area Start Time Power switch Rain Sensor Battery Capacity Settings Mower Operation Note: To ensure proper setup, verify that the mower is fully charged and is in contact with the docking station. Note: Make sure that the path of perimeter is compeltly clear before operating. Unlocking the Mower 1) Turn on the mower by switching the red button (located to the left of the LCD screen) 2) The LCD screen will show “Idle”. 3) Press the “Set” button one time.
Operation Settings Guide and Automatic Start 1) Unlock the mower. (If locked, see steps 1-7 in the Unlocking the Mower section.) 2) Once the mower is unlocked press the “Set” button to shift through the icons at the top of the screen. Setting Your Security PIN 1) Unlock the mower. (If locked, see steps 1-7 in the Unlocking the Mower section.) 2) Press the “Set” button until the lock icon is showing on the top the LCD screen.
Operation Setting the Mow Area Note: Roughly measure the size of your lawn to determine its area. 1) Unlock the mower. (If locked, see steps 1-7 in the Unlocking the Mower section.) 2) Press the “Set” button until the meters squared icon is showing at the top of the LCD screen. 3) Use the up and down arrows located on the “Home” and “Start” to increase or decrease the mowing area. 4) Press the “Set” button to save your mowing area.
Sensors Obstacle/Contact Sensor When the Robot Mower meets an obstacle, it will reverse and change direction to avoid the obstacle. If it does not find a new path within 3 seconds, the cutting motor stops. If it does not find a new path within 10 seconds, the robot will shut down and it will require a manual restart. Rain Sensor In case of heavy rain, the Robot Mower will automatically return to the docking station. It will automatically start mowing the next day at the time originally scheduled.
Color Customization CUSTOMIZE FOR YOUR STYLE WITH OPTIONAL DECORATIVE COLORED HOUSING ORANGE RED BLACK PINK BLUE WHITE GREEN GRAY TO BUY CUSTOM COLORS GOT TO WWW.MOWRO.COM Installation instructions - http://rm18colorswap.mowro.
Maintenance and Storage Cleaning the Robot Mower Lift the front and rear covers and remove any collected debris, grass clippings and dust using a soft brush, vacuum or damp cloth. Repeat for the bottom side of the robot using care when handling the blade disc and blades. It is important to keep the blades free from accumulated grass clippings to ensure proper operation of the robot mower. Ensure all retaining screws are secure.
Maintenance and Storage ! DANGER Blades are extremely sharp and will cut even when dull. Use caution when replacing. Wear gloves to protect hands from cuts. Storage Disconnect the docking station from the AC power adapter. Remove the ends of the boundary wire from the docking station. Turn the power switch off on the Robot Mower to protect the battery. Store the Robot Mower, docking station and AC adapter and cords in a dry frost free area. Cover the ends of the boundary wire with electrical tape.
Troubleshooting Testing the Docking Station Symptom Cause Action Robot doesn’t leave docking station. PIN not entered correctly. NOTE: Forgot PIN? Contact customer service Enter factory default PIN (0000) or PIN set by user. Battery is not charged. Allow robot to charge until battery symbol has 4 bars on LCD screen. Docking station not installed correctly. IN arrow on docking station should point to inside of working area. Boundary wire not installed correctly.
Information Codes Information Codes: Displayed on LCD Screen NOTE: How to Manually Restart - Place the machine within 1m near the boundary line, enter correct PIN code, then press “start”. Status Code Cause Solution E1 STOP Button has been engaged. Manually restart the mower. E2 Lift sensor has been triggered. Robot mower lifted? Wheel blocked? Remove foreign objects then manually restart the mower. E3 Robot mower is out of the boundary line perimeter.
Information Codes Information Codes: Displayed on LCD Screen NOTE: How to Manually Restart - Place the machine within 1m near the boundary line, enter correct PIN code, then press “start”. E13 Battery overheat. If this issue persists, please contact customer service. F1 Robot is out of boundary line perimeter.
IMPORTANT NOTICE We, the manufacturer, reserve the right to change the product and/ information usage only and the pictures and drawings depicted herein are for reference only. Warranty Repair and Service Do not return this product to the store for warranty issues or repair. Call our customer service department at 1-800-976-3009 or visit www.mowro.com for the location of the nearest service center. Record the information below for future reference. Serial No.
Call 1-800-976-3009 www.mowro.com Installation Video http://rm18installvideo.mowro.
