QUICK START GUIDE t w a t e ki n ne r g r hi te n u i a c yo a m an KIT l) nd L e er e M .co cle AN nn 21 a t is Ic ne ee LE Fut.
QUICK START GUIDE USER GUIDE u-line.com u-line.com WELCOME TO U-LINE Congratulations on your U-Line purchase. Your product comes from a company with over five decades of premium modular ice making, refrigeration, and wine preservation experience. U-Line creates products focused on functionality, style, and inspired innovations — paying close attention to even the smallest details. Applications include residential, outdoor, ADA height compliant, marine, and commercial.
QUICK START GUIDE u-line.com This Quick Start Guide covers the basics of installation and general use of your product.
QUICK START GUIDE u-line.com Safety and Warning ! DANGER NOTICE Your product may contain R600a (Isobutane) Please read all instructions before installing, which is a flammable hydrocarbon. To confirm, operating, or servicing the appliance. check serial tag inside of unit. It is safe for regular use. Do not use sharp objects to expedite Use this appliance for its intended purpose only and follow defrosting.
QUICK START GUIDE u-line.com Environmental Requirements NOTICE This model is intended for indoor/interior applications only local codes. This unit requires connection to a Electrical installation must observe all state and grounded (three-prong), polarized receptacle and is not to be used in installations that are open/ exposed to natural elements. that has been placed by a qualified electrician.
QUICK START GUIDE USER GUIDE u-line.com u-line.com USER GUIDE Water Hookup • (138 and 827 kPa). Crescent Makers PREPARE Ice PLUMBING Water Hookup The water valve uses a standard 1/4” (6.35 mm) compression fitting. U-Line recommends using accessory PREPARE PLUMBING water hook up kit – part # 80-54674-00. The kit includes The water valve uses a standard 1/4” (6.35 mm) a 10’ (3 m) braided flexible water supply line and a brass compression fitting. U-Line recommends using accessory hose fitting.
USER GUIDE QUICK START GUIDE u-line.com u-line.com 4. Break away filler feature in bushing with flat screwdriver. Remove ZLWK ɠDW screwdriver 5. Thread water line through back panel hole (with bushing). 6. Locate water valve inlet and connect to valve. 7. Turn on water supply and check for leaks. 8. Reinstall back panel. 9. Install retaining clip.
QUICK START GUIDE USER GUIDE u-line.com u-line.com USER GUIDE Water Hookup • (138 and 827 kPa). Clear Ice Machines PREPARE PLUMBING Water Hookup The water valve uses a standard 1/4” (6.35 mm) compression fitting. U-Line recommends using accessory PREPARE PLUMBING water hook up kit – part # 80-54674-00. The kit includes The water valve uses a standard 1/4” (6.35 mm) a 10’ (3 m) braided flexible water supply line and a brass compression fitting. U-Line recommends using accessory hose fitting.
QUICK START GUIDE USER GUIDE u-line.com u-line.com 3. Locate water 8. Install retaining clip. valve in the front of the unit and thread water supply line through. NOTICE Route the water supply line through the unit so it does not come into contact with any internal components other than the solenoid valve. Normal operation creates some vibration. A water supply line contacting an internal component or cabinet wall can cause excessive noise during operation or damage to the line. 4.
QUICK START GUIDE USER GUIDE u-line.com u-line.com USER GUIDE Water Hookup • (138 and 827 kPa). Nugget Ice Machines PREPARE PLUMBING Water Hookup The water valve uses a standard 1/4” (6.35 mm) compression fitting. U-Line recommends using accessory PREPARE PLUMBING water hook up kit – part # 80-54674-00. The kit includes The water valve uses a standard 1/4” (6.35 mm) a 10’ (3 m) braided flexible water supply line and a brass compression fitting. U-Line recommends using accessory hose fitting.
QUICK START GUIDE USER GUIDE 3. u-line.com Thread water line through back panel hole (with bushing). 4. Locate water valve inlet and connect to valve. 3 4 5. Turn on water supply and check for leaks. 6. Reinstall back panel.
QUICK START GUIDE QUICK START GUIDE u-line.com u-line.com Drain GRAVITY DRAIN Model numbers including “CL” or “NB” do not include a factory installed drain pump. Normal Proper Drain Model numbers including “CP” or “NP” include a factory installed drain pump.
QUICK START GUIDE QUICK START GUIDE u-line.com u-line.com FACTORY INSTALLED DRAIN PUMP Y-Branch Tailpiece P60 Pump Required If your drain line will run up to a stand pipe, disposal or Air Gap (Optional Hook-Up) spigot assembly, or does not otherwise meet the requirements for a gravity drain, you may have ordered a pre-installed U-Line P60 drain pump. Waste If you need to install a P60 drain pump into your unit, see 6KXW 2ɞ Valve DRAIN PUMP section in the User Manual.
QUICK START GUIDE USER GUIDE u-line.com Door Adjustments TO REVERSE THE DOOR 15” REFRIGERATORS HINGE COVER Hinge cover included with the literature bag is optional. To install hinge cover: 1. Press hinge cover squarely over hinge. Hinge Cover Remove grille: Remove the grille (see GRILLE INSTALLATION section of this guide). DOOR ALIGNMENT AND ADJUSTMENT Remove arrow clips: Align and adjust the door if it is not level or is not sealing 1. properly.
QUICKGUIDE START GUIDE USER 4. u-line.com u-line.com Remove door by tilting forward and lifting door off Install top hinge and door: bottom hinge. Retain shoulder washers; they will be reused. 5. Use a Philips screwdriver to remove hinge pin and reinstall on the opposite surface of the hinge. 6. Install arrow clips in holes. Remove bottom hinge: 1. Remove bottom hinge from cabinet using a 1/4” 1. socket. Rotate door 180o and lift the door on to the bottom hinge. 2.
QUICK START GUIDE USER GUIDE u-line.com Door Adjustments REVERSING THE DOOR 24” MODELS Location of the unit may make it desirable to mount the door on the opposite side of the cabinet. HINGE COVER The hinge hardware will be removed and reinstalled on the Hinge cover included with the literature bag is optional. opposite side of the cabinet. TO REVERSE THE DOOR To install hinge cover: 1. Press hinge cover squarely over hinge. Hinge Cover Remove arrow clips: 1.
QUICK START GUIDE USER GUIDE 3. u-line.com u-line.com Remove door by tilting forward and lifting door off Install top hinge and door: bottom hinge. Retain shoulder washers; they will be reused. 4. Top Hinge Right Side Insert arrow clips into holes Top Hinge Left Side Pivot Screw Remove bottom hinge: 1. 1. Remove bottom hinge from cabinet using a T-25 TORX install the pivot screw in the same hole from the screw driver to remove three screws. 2.
QUICK START GUIDE u-line.com Door Adjustments TO REVERSE THE DOOR CRESCENT ICE AND CLEAR ICE MACHINES HINGE COVER Hinge cover included with the literature bag is optional. To install hinge cover: 1. Press hinge cover squarely over hinge. Hinge Cover Remove arrow clips: 1. With a puddy knife or other flat tool, gently pry each arrow clip from hinge mounting holes. 2. DOOR ALIGNMENT AND ADJUSTMENT Set aside arrow clips to be reused on the opposite side.
QUICK START GUIDE 1. 2. u-line.com 4. Remove door by tilting forward and lifting door off Install gasket into channel, bottom hinge. Retain shoulder washers; they will be beginning at one corner and reused. pressing in firmly. 5. Insert arrow clips into holes Press down on middle horizontal portion of gasket until it adheres to the door surface. Remove bottom hinge: 1. Gasket Channel Remove bottom hinge from cabinet using a 1/4” Press down firmly socket.
QUICK START GUIDE u-line.com Door Adjustments TO REVERSE THE DOOR NUGGET ICE MACHINES HINGE COVER Hinge cover included with the literature bag is optional. To install hinge cover: 1. Press hinge cover squarely over hinge. Hinge Cover Remove arrow clips: 1. With a puddy knife or other flat tool, gently pry each arrow clip from hinge mounting holes. 2. DOOR ALIGNMENT AND ADJUSTMENT Set aside arrow clips to be reused on the opposite side.
QUICK START GUIDE 1. u-line.com Remove door by tilting forward and lifting door off 4. bottom hinge. Retain shoulder washers; they will be remove plunger bracket reused. 2. Take out 2 screws and from gasket channel. Insert arrow clips into holes Plunger Bracket Remove bottom hinge: 1. Gasket Channel Remove bottom hinge from cabinet using a 1/4” socket. 5. Install plunger bracket at the opposite corner, utilizing the 2 pre-drilled holes. 2.
QUICK START GUIDE u-line.com General Installation Install top hinge and door: LEVELING INFORMATION Top Hinge Right Side 1. Use a level to confirm the unit is level. Level should be placed along top edge and side edge Top Hinge Left Side as shown. Pivot Screw 1 1. Remove pivot screw from hinge, flip hinge over, and install the pivot screw in the same hole from the 2. opposite surface. 2.
QUICK START GUIDE QUICK START GUIDE u-line.com u-line.
QUICK START GUIDE QUICK START GUIDE u-line.com u-line.
QUICK START GUIDE u-line.com Control Operation CONVERTIBLE FREEZER CONTROL FUNCTION GUIDE FUNCTION COMMAND NOTES ON/OFF Press Unit will immediately turn On or OFF Press Leave interior light on and release and release to leave interior light on for 12 hours; press again to deactivate After 12 hours, factory default is restored; light will turn on when door is open When the display is flashing, press Adjust Temperature Press or and release or to adjust the set point temperature.
QUICK START GUIDE u-line.com Control Operation NUGGET ICE MACHINES CONTROL FUNCTION GUIDE FUNCTION COMMAND NOTES ON/OFF Press Unit will immediately turn On or OFF Adjust ice density See “Ice” section Enable Sabbath Mode Press and release and hold for 5 seconds and release The oF / oC symbol will flash briefly after 5 seconds.
QUICK START GUIDE u-line.com First Use Approximate time required (empty unit) when converting between refrigerator and freezer: CRESCENT ICE MAKERS Initial startup requires no adjustments. • 30ºF to 0ºF - 1 hour U-Line recommends discarding the ice produced during the • 0ºF to 38ºF - 4 hours first two to three hours of operation to avoid possible dirt or scale that may dislodge from the water line.
QUICK START GUIDE QUICK START GUIDE u-line.com u-line.com Ice During periods of limited use or high ambient CRESCENT ICE MAKERS Gently shake the bucket to break apart cubes. If not using temperatures, it is common for cubes to fuse together. the ice maker regularly, empty the ice bucket periodically to ensure fresh cubes. ICE MAKER OPERATION When the ice bucket is full, the ice making mechanism will It is normal for cubes to appear cloudy. The cause is air shut off.
QUICK START GUIDE QUICK START GUIDE u-line.com u-line.com CLEAR ICE MACHINES ! CAUTION ICE CUBE THICKNESS ADJUSTMENT Too large of an adjustment to the screw can Ice thickness adjustment should only be made cause the water to overflow the ice maker and one increment at a time. Allow ice maker can cause property damage. production to stabilize for 24 hours before rechecking ice thickness. 3.
QUICK START GUIDE QUICK START GUIDE u-line.com USER GUIDE Ice NUGGET ICE MACHINES Your clear ice machine is preset to produce ice between the optimal dimensions illustrated below: NUGGET ICE MACHINES Ice The Nugget Ice Machine produces cylindrical bits of Cube Details 1/4" TO 1/2" (6.4 mm to 12.7 mm) DIMPLE u-line.com compressed ice approximately 3/ ” x 1/2”. The Nugget Ice Machine produces4cylindrical bits of 1/16" TO 1/8" (1.6 mm to 3.2 mm) ICE BRIDGE 3 /4”senses x 1/2”. the bin is full.
USER GUIDE QUICK START GUIDE u-line.com u-line.com Cleaning Using abrasive pads such as ScotchBrite™ will EXTERIOR CLEANING become blurred. cause the graining in the stainless steel to Vinyl Clad (Black or White) Models Clean surfaces with a mild detergent and warm water Rust not cleaned up promptly can penetrate the solution. Do not use solvent-based or abrasive cleaners. surface of the stainless steel and complete Use a soft sponge and rinse with clean water.
USER GUIDE QUICK START GUIDE u-line.com 5. Re-install the standpipe into the water trough. NOTICE Use only U-Line Ice Machine Cleaner (Part No. 80-54081-00), available from your dealer or direct from your local parts distributor. To locate a parts distributor near you, visit u-line.com. It is a violation of federal law to use this solution in Evaporator a manner inconsistent with its labeling. Use of any other cleaner can ruin the finish of the evaporator and will void the warranty.
cleaner. Rinse the interior using a soft sponge and clean water. QUICK START GUIDE Do not use any solvent-based or abrasive Stainless Models cleaners. These types of cleaners may transfer taste u-line.com Stainless door panels, handles and frames can discolor and/or odor to the interior products and damage or discolor when exposed to chlorine gas, pool chemicals, saltwater or the interior. cleaners with bleach. 9.
begins, it can be canceled by pressing hot (min. 100º F) potable water. This will melt ice three times. Press once more to start making ice. The clean cycle USER GUIDE QUICK START GUIDE will automatically cancel if user fails to activate control at inside the dispenser tube. It is normal for some water to flow from the ice dispenser tube and exit from the u-line.com u-line.com vent tube while pouring. Omit this step if no ice is in steps 2, 3b, and 5b within 2 hours. the ice dispenser tube.
USER QUICKGUIDE START GUIDE 6. When u-line.com u-line.com 05 appears in the display, 3 soft tones will sound, indicating the cleaning phase is complete a. Remove and discard water filter if applicable by rotating 1⁄4 turn counterclockwise. b. Use the remaining cleaning solution to wipe the manifold and surrounding area. Rinse with clean potable water. Manifold (Filter Models Only) c. Using the hose and funnel, slowly pour 1.5 quarts (48 oz.) of clean potable water into the ice dispenser tube.
U-Line Corporation (U-Line) Limited Warranty One Year Limited Warranty For one year from the date of original purchase, this warranty covers all parts and labor to repair or replace any part of the product that proves to be defective in materials or workmanship. For products installed and used for normal residential use, material cosmetic defects are included in this warranty, with coverage limited to 60 days from the date of original purchase.
