TRX-4 Sport Complete LED Light Kit Installation

Covers Parts #8084, 8085, 8086, 8087, 8089
LED Light Kit Installation Instructions (fits #8111 or #8112 bodies)
LED Lighting Module Installation (Fig. 1) (#8085 Kit only):
Your model may differ slightly from the one shown in the illustration, but
installation is the same.
1. Install the LED lighting
module (A) on the left
chassis floor pan. Secure
with the 2.5x15mm cap
screws (2).
2. Remove the screws from
the receiver box cover and
wire clamp; remove the
cover and clamp (B).
3. Remove the two 3x10mm
countersunk cap screws
from the battery tray (C).
4. Lift up the battery tray and
route the red wire (male
connector) from the LED
lighting module to the
right side of the chassis
and through the hole in
the receiver box. Plug the
connector into channel 1
of the receiver (D). Note:
The connector can be
plugged into any non-
telemetry channel on the
TQi receiver.
5. Apply an additional bead of silicone grease (Traxxas part #1647, sold
separately) to the wire clamp. The grease will improve sealing. Reinstall the
clamp and screws.
6. Make sure the o-ring is properly seated into the groove in the receiver box so
that the cover will not pinch it or damage it in any way.
7. Install the cover and screws. Inspect the cover to make sure the o-ring seal is
not visible.
8. Reinstall the screws in the battery tray.
9. Connect the black wire (red female connector) from the LED lighting module
to the red wire (male connector) exiting the XL-5 HV electronic speed control.
Body Modification
1. Install the included templates on the body.
Align the arrows with the body lines on the
front grille and the tailgate as shown in Fig.
2 and 3.
2. Using a tapered body reamer, carefully cut
the holes in the truck body for the screw
bosses on the front grille retainer and the
tailgate panel (note the hole diameters
indicated on the templates and the
corresponding diameter measurements on
the body reamer).
3. Using a hobby knife, carefully cut out the holes in the truck body for the
headlight housing and the tail light lens.
Fig. 1
A
B
C
D
Visitez Traxxas.com/manuals pour télécharger
les instructions dans votre langue.
Visite la página Traxxas.com/manuals para
descargar el instrucciones en su idioma.
Auf Traxxas.com/manuals, können Sie
anleitung in Ihrer Sprache downloaden.
#8085 Kit Contents:
• LED lighting module
• Distribution block
• Front grille
• Front grille retainer
• Headlights harness assembly
• Headlight clamps (2)
• Tailgate panel
• Tailgate panel retainer
• Tail lights harness assembly
• Tail light clamps (2)
• Jumper
• 2.5x8mm button-head screws (8)
• 2.6x8mm button-head screws (2)
• 2.5x10mm button-head screws (2)
• 2.5x15mm cap screws (2)
• Zip tie mount (3)
• Zip ties (3)
• Body templates
#8087 Kit Contents (parts #8120 or
#8120X required, sold separately)*:
• LED roof light bar
• 2.5x8mm cap screws (2)
• Zip tie mount (1)
• Zip tie (1)
#8086 Kit Contents (parts #8120 or
#8120X required, sold separately)*:
• Expedition rack scene lights
harness assembly
• 2.5x8mm cap screws (8)
• Zip tie mount (1)
• Zip tie (1)
Tool required:
• Safety glasses
• 2.0mm hex wrench
• 1.5mm hex wrench
• Hobby knife
• Small file (optional)
• Tapered body reamer (part #3433 or #3433X,
sold separately)
• Body scissors (part #3431 (straight tip) or #3132
(curved tip), sold separately)
• Rotary tool (such as Dremel®) (optional)
FRONT
4.5mm
0.177"
4.5mm
0.177"
Fig. 2
REAR
4mm
0.1575"
4mm
0.1575"
Fig. 3
Tapered Body Reamer
Diameter Measurements
CAUTION: RISK OF INJURY!
Always wear eye protection when using motorized tools.
Use care with hobby knives, tapered reamers, and other
cutting tools as they are extremely sharp and can cause
severe injury, deep cuts, and/or punctures.
#8084 Kit Contents
(parts #8116 and #8117 required,
sold separately):
• Headlights harness assembly
• Tail lights harness assembly
TRAXXAS.com
Traxxas, 6250 Traxxas Way, McKinney, TX 75070, Phone: [phone], Fax: [phone], e-mail: [e-mail]
HKC18060-R04 Rev 200130
*4-in-2 wire harness (part #8089, sold
separately) required when installing
both the #8086 and #8087 kits.