Instructions / Assembly

ManualsBrandsThe RAQ ManualsElectricalRAQ in a Box-2-Solar Panel Roof Mounting System-Universal Pre assembled

SR-3000: 126” X 9”X 8.5” 50 LBS

SR-1000: 43.5” X 9” X 8.5” 21.5 LBS

What is included in The RAQ Solar Mounng Kits?

SR-3000 Includes

Self squaring 3 Panel Rails with adjustable panel clamps, adjustable

anchor bases, ashing and all hardware to assemble

SR-1000 Includes

Self squaring 1 Panel Rail, with adjustable panel clamps, adjustable

anchor bases, ashing and all hardware to assemble

SR-0700 Start Bracket Kit

For a stand alone unit or to start a row, and grounding for stand alone

or row of rails (up to 18 max.)

SR-0400 Addional Wind Zone Kit

4 addional ashing, 4 adjustable anchor bases, end clips and all hard-

ware to assemble.

SR-0900 Micro Inverter Bracket Kit

3 Micro inverter brackets and all hardware to assemble

What will I need to Install The RAQ Solar Mounng

Kits?

Safety Equipment:

Ladders, eye protecon , hard hats and all fall protecon

Tools:

1/2” Socket and Driver (with extra charged baeries on hand)

3/8” Cold Rolled Drill Bit (incase of odd anchor feet placement, or

misaligned raer spacing)

4 1/2” Long Wood Drill Bit (for predrilling lag bolt penetraons)

Open by removing strap that is securing box with box cuer

Unpack Contents and verify order is accurate

Familiarize yourself with the various components and

prepare kit for installaon

Take all equipment on roof and set up for installaon

Cut zip e on assembly

Installation

Instructions

Summary of content (5 pages)

PAGE 1
Installation Instructions What is included in The RAQ Solar Mounting Kits? SR-3000 Includes Self squaring 3 Panel Rails with adjustable panel clamps, adjustable anchor bases, flashing and all hardware to assemble What will I need to Install The RAQ Solar Mounting Kits? SR-1000 Includes Self squaring 1 Panel Rail, with adjustable panel clamps, adjustable anchor bases, flashing and all hardware to assemble Safety Equipment: SR-0700 Start Bracket Kit Ladders, eye protection , hard hats and all fall prote
PAGE 2
6 5 Open the assembly until bi-fold center brace (s) is straight, ensure holes are lined up for securing 7 Place T23 Bolt into predrilled hole by bi-fold hinge ensuring it is lined up with the predrilled hole below and tighten. 8 Locate all squaring arms; connected to the underside of cross brace, rotate them out to the point where they naturally land on the top of rail.
PAGE 3
12 11 Before we secure rail (s) into roof we must be aware of a few things. First, anchor bases will always point up to the peak of the roof. Secondly, placement of preinstalled anchor bases may need to be relocated (depending on rafter spacing on roof being installed onto and wind and snow load capacities) . Preassembled anchor base spacing is set for 24” on center. Now is the time to configure rafter spacing for proper installation of anchor bases onto rail to be lined up with the rafter spacing.
PAGE 4
17 Once the rafter location is determined based on your installation layout configuration predrilled holes should be made with the 4 1/2” drill bit in the location where anchor bases will be installed into roof rafters. Note: Anchor bases may need additional adjustments off the rail before they line up with rafters. Start from the top work your way to the right, then below.
PAGE 5
23 Starting from the top row, from left to right, place the #1 PV module in the portrait position and place the module onto the 1st RAQ unit (under panel clamps on start brackets ) and hold up on right side to attach PV to inverter cables. 25 Before securing the next set of panel clamps onto 1st PV bring in PV module # 2 onto the next RAQ unit to the right. Install just like #1; by setting and tilting left side of PV in portrait position under panel clamps, attach PV to inverter and set down.