Datasheet


    
SLLS363A − SEPTEMBER 1999 − REVISED NOVEMBER 2000
10
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
DISSIPATION RATING TABLE
PACKAGE
T
A
≤ 25°C
POWER RATING
DERATING FACTOR
†
ABOVE T
A
= 25°C
T
A
= 70°C
POWER RATING
PZP
‡
4.48 W 44.78 mW/°C 2.46 W
PZP
§
2.28 W 22.78 mW/°C 1.25 W
PZP
¶
1.32 W 13.19 mW/°C 0.73 W
†
This is the inverse of the traditional junction-to-ambient thermal resistance (R
θJA
).
‡
1 oz. trace and copper pad with solder.
§
1 oz. trace and copper pad without solder.
¶
Standard JEDEC High-K board
NOTE: For more information, refer to TI application note PowerPAD Thermally Enhanced Package
TI literature number SLMA002.
recommended operating conditions
PARAMETER MIN TYP
†
MAX UNIT
Supply voltage, V
DD
Source power node 3 3.3 3.6 V
Supply voltage, V
DD
Nonsource power node 2.7
‡
3 3.6
High-level input voltage, V
IH
Case 1 (bus holder): ISO=V
DD
, V
DD_5V
= V
DD
Case 2 (5V Tol): ISO
=V
DD
, V
DD_5V
= 5V
LREQ, CTL0, CTL1, D0−D7
2.6 V
High-level input voltage, V
IH
C/LKON, PC0, PC1, PC2, ISO, PD 0.7×V
DD
V
RESET 0.6×V
DD
V
Low-level input voltage, V
IL
Case 1 (bus holder): ISO=V
DD
, V
DD_5V
= V
DD
Case 2 (5V Tol): ISO
=V
DD
, V
DD_5V
= 5 V
LREQ, CTL0, CTL1, D0−D7
1.2 V
Low-level input voltage, V
IL
C/LKON, PC0, PC1, PC2, ISO, PD 0.2×V
DD
V
RESET 0.3×V
DD
V
Output current, I
O
TPBIAS outputs −5.6 1.3 mA
Maximum junction temperature T
J
(see
R
θJA
= 17.85°C/W, T
A
=70°C 93.6
Maximum junction temperature T
J
(see
R
θ
JA
values listed in thermal
characteristics table)
R
θJA
=28.22°C/W, T
A
=70°C 107.3
°C
R
θJA
values listed in thermal
characteristics table)
R
θJA
=49.17°C/W, T
A
=70°C 135.1
C
Differential input voltage, V
ID
Cable inputs, during data reception 118 260
mV
Differential input voltage, V
ID
Cable inputs, during arbitration 168 265
mV
Common-mode input voltage, V
IC
TPB cable inputs, source power node 0.4706 2.515
V
Common-mode input voltage, V
IC
TPB cable inputs, nonsource power node 0.4706 2.015
‡
V
Power-up reset time, t
pu
RESET input 2 ms
TPA, TPB cable inputs, S100 operation ±1.08
Receive input jitter
TPA, TPB cable inputs, S200 operation ±0.5
ns
Receive input jitter
TPA, TPB cable inputs, S400 operation ±0.315
ns
Between TPA and TPB cable inputs, S100 operation ±0.8
Receive input skew
Between TPA and TPB cable inputs, S200 operation ±0.55
ns
Receive input skew
Between TPA and TPB cable inputs, S400 operation ±0.5
ns
†
All typical values are at V
DD
= 3.3 V and T
A
= 25°C.
‡
For a node that does not source power, see Section 4.2.2.2 in IEEE 1394a.