Datasheet
ELECTRICAL CHARACTERISTICS
PTH04T230W , PTH04T231W
SLTS271C – SEPTEMBER 2006 – REVISED MARCH 2009 .............................................................................................................................................
www.ti.com
PTH04T230W
T
A
=25 ° C, V
I
= 5 V, V
O
= 3.3 V, C
I
= 330 µ F, C
O
1 = 100 µ F ceramic, C
O
2 = 150 µ F non-ceramic, and I
O
= I
O
max (unless
otherwise stated)
PARAMETER TEST CONDITIONS PTH04T230W UNIT
MIN TYP MAX
I
O
Output current Over V
O
range 25 ° C, natural convection 0 6 A
0.69 ≤ V
O
≤ 1.7 2.2 5.5
V
I
Input voltage range Over I
O
range V
1.7 < V
O
≤ 3.6 V
O
+0.5
(1)
5.5
Output adjust range Over I
O
range 0.69 3.6 V
Set-point voltage tolerance ± 0.5 ± 1.0
(2)
%V
o
Temperature variation – 40 ° C < T
A
< 85 ° C ± 0.3 %V
o
V
O
Line regulaltion Over V
I
range ± 2 mV
Load regulation Over I
O
range ± 2 mV
Total output variation Includes set-point, line, load, – 40 ° C ≤ T
A
≤ 85 ° C ± 1.5
(2)
%V
O
R
SET
= 1.21 k Ω , V
O
= 3.3 V 94%
R
SET
= 2.38 k Ω , V
O
= 2.5 V 92%
R
SET
= 4.78 k Ω , V
O
= 1.8 V 90%
η Efficiency I
O
= 6 A R
SET
= 7.09 k Ω , V
O
= 1.5 V 89%
R
SET
= 12.1 k Ω , V
O
= 1.2 V 87%
R
SET
= 20.8 k Ω , V
O
= 1.0 V 85%
R
SET
= 689 k Ω , V
O
= 0.7 V 81%
V
O
Ripple (peak-to-peak) 20-MHz bandwidth 1 %V
O
I
LIM
Overcurrent threshold Reset, followed by auto-recovery 10 A
w/o TurboTrans Recovery Time 100 µ Sec
C
O
1 = 100 µ F, ceramic
C
O
2 = 150 µ F,
V
O
Overshoot 100 mV
non-ceramic
2.5 A/ µ s load step
w/o TurboTrans
(3)
Recovery Time 120 µ Sec
50% to 100% I
O
max
Transient response C
O
1 = 100 µ F, ceramic
V
I
= 3.3 V
V
O
Overshoot 60 mV
C
O
2 = 990 µ F, Type B
V
O
= 2.5 V
with TurboTrans Recovery Time 180 µ Sec
C
O
1 = 100 µ F, ceramic
C
O
2 = 990 µ F, Type B
V
O
Overshoot 35 mV
R
TT
= 1.54 k Ω
I
IL
Track input current (pin 9) Pin to GND -130
(4)
µ A
dV
track
/dt Track slew rate capability C
O
≤ C
O
(max) 1 V/ms
V
I
increasing, R
UVLO
= OPEN 1.95 2.19
Adjustable Under-voltage lockout
UVLO
ADJ
V
I
decreasing, R
UVLO
= OPEN 1.3 1.5 V
(pin 10)
Hysteresis, R
UVLO
≤ 52.3 k Ω 0.5
Input high voltage (V
IH
) Open
(5)
V
Inhibit control (pin 10) Input low voltage (V
IL
) -0.2 0.6
Input low current (I
IL
), Pin 10 to GND 125 µ A
I
in
Input standby current Inhibit (pin 10) to GND, Track (pin 9) open 5 mA
f
s
Switching frequency Over V
I
and I
O
ranges, SmartSync (pin 1) to GND 300 kHz
f
SYNC
Synchronization (SYNC) frequency 240 400 kHz
V
SYNCH
SYNC High-Level Input Voltage 2 5.5 V
V
SYNCL
SYNC Low-Level Input Voltage 0.8 V
t
SYNC
SYNC Minimum Pulse Width 200 nSec
(1) The minimum input voltage is 2.2 V or (V
O
+ 0.5) V, whichever is greater.
(2) The set-point voltage tolerance is affected by the tolerance and stability of R
SET
. The stated limit is unconditionally met if R
SET
has a
tolerance of 1% with 200 ppm/C or better temperature stability.
(3) Without TurboTrans, the minimum ESR limit of 7 m Ω must not be violated.
(4) A low-leakage ( < 100 nA), open-drain device, such as MOSFET or voltage supervisor IC, is recommended to control pin 9. The
open-circuit voltage is less than V
I
.
(5) This control pin has an internal pull-up. Do not place an external pull-up on this pin. If it is left open-circuit, the module operates when
input power is applied. A small, low-leakage ( < 100 nA) MOSFET is recommended for control. The open-circuit voltage is less than 3.5
Vdc. For additional information, see the related application information section.
4 Submit Documentation Feedback Copyright © 2006 – 2009, Texas Instruments Incorporated
Product Folder Link(s): PTH04T230W PTH04T231W