Barcode Scanner User’s Manual
Notice 1. Please carefully read the User Manual before using the barcode scanner. 2. All software, including firmware, furnished to the user is on a licensed basis. 3. The right is reserved to make changes to any software or product to improve reliability, function, or design. 4. The material in this manual is subject to change without notice.
Contents Scanning And Set Defaults ......................................................................... 5 Programming instruction............................................................................ 6 Programming without Parameter ........................................................ 6 Programming with Parameter .............................................................. 7 Interface selection ......................................................................................
UK/Plessey ................................................................................................ 78 GS1 DataBar (GS1 DataBar Truncated)..................................................... 81 GS1 DataBar Limited................................................................................. 83 GS1 DataBar Expanded ............................................................................. 85 Advanced Bar Code Data Formatting ....................................................... 86 Prefix ...
Scanning When the scanner is scanning, ensure the scan line crosses every bar and space of the bar code. RIGHT RIGHT WRONG WRONG the Scan Line on the bar code Set Defaults And Information Display Set Factory Defaults If you wish to return the base unit to the entire factory default settings (radio communication setting is not included), scan the barcode ”Set Defaults”.
Communication Information and Battery Power Display Wireless scanner Battery Power Display Communication Channel and ID Number or Scanner Display Programming instruction The scanner is programmed by scanning the setting barcode in the Manual. There are two kinds of Programming instructions. One of them programmed with Parameter and the other one of them without Parameter. Programming without Parameter When programming without parameter, only one setting barcode is need to be scanned.
Programming with Parameter It is need to scan more than one setting barcode to program the scanner with parameter. Program Parameters The steps of programming are: 1. Scan the Function Setting Barcode. The Scanner will issue a "beep” sound, and the Red LED is on until the program is finished. 2. Scan the parameters bar code. The parameters may be one or more than one digits.
3. Scan the setting barcode “Finish Setting”. If it is programmed successful , the scanner will issue a “beep beep” sound, but issue a “beep beep beep” sound when fails. e.g.：Set min. code length of Code 128 to 5 chars ： 1 ： Open the manual and turn chapter "code128 ". Scan the setting bar code ○ “Scan Min. Code Length”. Scan Min.
Interface selection This scanner supports interfaces such as keyboard wedge, RS-232 serial wedge, and USB interface. Typically, host is able to identify the host port type automatically. In extreme cases, host port may need setting manually if the host fails to identify it.
Scanning Mode Setting Good-read off scanning Mode: The trigger button must be pressed once to activate scanning. The light source of scanner stops scanning when there is a successful reading or no code is decoded after the Stand-by duration elapsed. Select Good-read off scanning Mode * Auto-detection scanning Mode: The scanner will start scan Automatically if any object enter the scan area.
Click Scanning Mode: When the button is click, the scanner will keep scanning the barcode until the barcode is reader or the Stand-by duration elapsed. Click Scanning Mode Continuous Scanning mode: the scan engine is always scanning and decoding. The module will read the barcode which gets into the scanning area automatically. Only when the barcode that has been read gets out of the scanning area, the module can read the next barcode.
Keyboard wedge Keyboard type IBM AT，PS/2 * Other（Reserved） Keyboard layout USA * Italian French Turkish F Turkish Q 12
Clock period According to the PS2 protocol, the clock is provided by the device, e.g. keyboard or scanner, with the period between 60us to 200us.
Delay-after-compound-key In some rare occasions, machine with low speed PS2 communication portwould require a free time gap following the press/release of the compound key (Shift, Ctrl or Alt).
Power-on simulation All of the PCs check the keyboard status during power-on self test. It simulates keyboard timing and passes keyboard present status to the PC during power-on. Enable Disable * Inter-character delay This delay is inserted after each data character transmitted.
40 mS 80 mS Inter-byte delay: This delay is inserted after each byte transmitted. Normally a character is comprised of three or above bytes.
Caps Lock reversion By setting enable, the status of Caps Lock key (i.e. being pressed ON or OFF) on the keyboard is simulated in a reversion status. Enable Caps Lock * Disable Caps Lock Caps Lock override If this function is enabled, on AT or AT notebook hosts, the keyboard ignores the state of the Caps Lock key.
USB interface USB device type HID Keyboard* Virtual RS232 Port（reserved） IBM Table Top USB IBM Hand-Held USB USB OPOS Hand-Held 18
USB Keyboard layout USA* German French Other USB Keystroke Delay No Delay* 20mS 40mS 19
USB CAPS Lock Override Enable* Disable USB Ignore Unknown Characters Enable Disable* 20
Emulate Keypad Enable this to send all characters as ASCII sequences over the numeric keypad. For example, ASCII A transmits as “ALT make” 0 6 5 “ALT Break Enable Disable* Simulated Caps Lock Enable this to invert the upper and lower case characters on the scanned bar code as if the Caps Lock state is enabled on the keyboard.
USB Keyboard FN 1 Substitution This option applies only to the USB HID Keyboard Emulation device. When enabled, this allows replacing any FN 1 characters in an EAN 128 bar code with a Key Category and value chosen by the user.
RS-232 Interface Baud Rate 2400 4800 9600* 19200 38400 57600 23
Handshaking None：Scan the bar code below if no Hardware Handshaking is desired None（Default） Standard RTS/CTS：Scan the bar code below to select Standard RTS/CTS Hardware Handshaking. Standard RTS/CTS RTS/CTS Option 1: When RTS/CTS Option 1 is selected, the scanner asserts RTS before transmitting and ignores the state of CTS. The scanner de-asserts RTS when the transmission is complete. RTS/CTS Option 1 RTS/CTS Option 2: When Option 2 is selected, RTS is always high or low (user-programmed logic level).
RTS/CTS Option 3: When Option 3 is selected, the scanner asserts RTS prior to any data transmission, regardless of the state of CTS. The scanner waits up to Host Serial Response Time-out for CTS to be asserted. If CTS is not asserted during this time, the scanner issues an error indication and discards the data. The scanner de-asserts RTS when transmission is complete.
ACK/NAK with ENQ: This combines the two previous options. For re-transmissions of data, due to a NAK from the host, an additional ENQ is not required. ACK/NCK with ENQ XON/XOFF: An XOFF character turns the scanner transmission off until the scanner receives an XON character. There are two situations for XON/XOFF: • XOFF is received before the scanner has data to send. When the scanner has data to send, it waits up to Host Serial Response Time-out for an XON character before transmission.
Host Serial Response Time-out 2 sec（Default） 5 sec 7.
Stop Bit Select 1 Stop Bit（Default） 2 Stop Bit Parity None（Default） Odd Even Select Mark parity and the parity bit is always 1. Mart Select Space parity and the parity bit is always 0.
Inter character Delay This parameter specifies the inter character delay inserted between character transmissions.
Global Settings Element amendment Enable Element amendment * Disable Element amendment Printable character Output only Enable Disable* Decoder optimization Enable Decoder optimization * Disable Decoder optimization 30
Save Power Enable* Disable Standby duration 2 second 5 second * 10 second 20 second 31
Double confirm Disable Double confirm* 2 Times 5 Times 10 Times Same barcode delay time If a barcode has been scanned and output once successfully, the laser beam must be off or moved away from the barcode beyond delay time to active scanning the same barcode. When this feature is set to be “0xFF”, then the delay time is indefinite.
Global Max./Min. code length Global Max. code length（2 Digits;00~99;99*) Global Min.
Indication Volume of beeper High* Middle Low Mute Beep tone High Tone Middle Tone * Low Tone 34
Wire Less Communication Setting Unpair the scanner from host Unpair the scanner from host Pair Scanner with Host Pairing is the process by which a scanner initiates communication with a host. The scanner with the Host pairing as follows: 1. Connect the scanner to the Host with the Charging Cable. 2. Press the "Pairing Button” until the Scanner issued a "beep beep" sound. NOTE: A host is able to work with as more as 99 scanners at the same time.
Wire Less Channel When there are more than one host work in the same Space, every host has to work in different channel. Channel is set as follows: 1. Open a Notepad or other text editor. 2. Press the "Channel Settings button" to change the channel of a host, and the channel NO will be displayed in the screen. Scanner ID Set the Scanner ID（2 Digits；00~99；00*） Add Scanner ID as Prefix If this item is enabled, the scanner will add its ID as prefix of every barcode. E.g.
Power off Interval Power Off Interval（2 Digits；00~99seconds；15seconds*）4 Shut down the Scanner Immediately RF operating mode: NO-Store Mode: Do not batch data. The scanner attempts to transmit every scanned barcode. If the transmission is failed, the barcode data is ignored and issued a "beep beep beep” sound. Auto-store Mode: The scanner starts storing barcode data when it loses its connection to a host (for example, when a user holding the scanner walks out of range).
Manual Transmission Mode : Data transmission is triggered by scanning “Start transfer Bar Code Data” . Auto-Store Mode* NO-Store Mode Manual Transmission Mode Start transfer Bar Code Data (for Manual Transmission Mode) Wire Less Communication Inter-character delay Scan Wire Less Communication Inter-character delay（2 Digits； 0.0~9.9seconds；0.
EAN-13 and ISBN/ISSN Enable/Disable EAN-13 Enable EAN-13* Disable EAN-13 EAN-13 Check Digit Verification Enable EAN-13 Check Digit Verification * Disable EAN-13 Check Digit Verification EAN-13 Check Digit Transmission Transmit EAN-13 Check Digit* Do Not Transmit EAN-13 Check Digit 39
Supplement Digits 2 Digits 5 Digits 2 Digits or 5 Digits None* ISBN/ISSN Conversion Convert EAN-13 to ISBN/ISSN Do Not Convert EAN-13 to ISBN/ISSN* 40
Code ID setting Code ID is a one-or-two-character string used to represent the symbol upon a succeeding reading. If you want application to transmit Code ID, you must set Code ID transmission to be enabled. Refer to the chapter of Scan Code ID（2Bit；00~FF； 65* ‘e’）C Insert String 1 Selection Scan one digits parameter (0~6) that: 0: no string insert to the barcode; 1~6: insert to the barcode G1~G6 to the barcode.
EAN-8 Enable/Disable EAN-8 Enable EAN-8* Disable EAN-8 EAN-8 Check Digit Verification Enable EAN-8 Check Digit Verification * Disable EAN-8 Check Digit Verification EAN-8 Check Digit Transmission Transmit EAN-8 Check Digit L* Do Not Transmit EAN-8 Check Digit 42
Supplement Digits 2 Digits 5 Digits 2 Digits or 5 Digits None* Expand EAN-8 to EAN-13 Expand EAN-8 to EAN-13 Do Not Convert EAN-8 to EAN-13* 43
Code ID setting (“d”) Scan Code ID（2 Digits；00~FF； 64*） Insert String 1 Selection Scan Insert String 1（1 Digit；0~6；0*） Insert String 2 Selection Scan Insert String 2（1 Digit；0~6；0*） 44
UPC-A Enable/Disable UPC-A Enable UPC-A 0* Disable UPC-A UPC-A Check Digit Verification Enable UPC-A Check Digit Verification * Disable UPC-A Check Digit Verification UPC-A Check Digit Transmission Transmit UPC-A Check Digit * Do Not Transmit UPC-A Check Digit 45
Supplement Digits 2 Digits 5 Digits 2 Digits or 5 Digits None * UPC-A Truncation/Expansion Expand UPC-A to EAN-13 Truncate leading zeros None* 46
Code ID setting (“b”) Scan Code ID（2 Digits；00~FF； 62*） Insert String 1 Selection Scan Insert String 1（1 Digit；0~6；0*） Insert String 2 Selection Scan Insert String 2（1 Digit；0~6；0*） 47
UPC-E Enable/Disable UPC-E Enable UPC-E* Disable UPC-E UPC-E Check Digit Verification Enable UPC-E Check Digit Verification * Disable UPC-E Check Digit Verification UPC-E Check Digit Transmission Transmit UPC-E Check Digit * Do Not Transmit UPC-E Check Digit 48
Supplement Digits 2 Digits 5 Digits 2 Digits or 5 Digits None* UPC-E Truncation/Expansion Truncate leading zeros Expand UPC-E to EAN-13 Expand UPC-E to UPC-A None* 49
Code ID setting (“c”) Scan Code ID（2 Digits；00~FF； 63*） Insert String 1 Selection Scan Insert String 1（1 Digit；0~6；0*） Insert String 2 Selection Scan Insert String 2（1 Digit；0~6；0*） 50
Code128 C Enable/Disable Code128 Enable Code 128* Disable Code 128 Code128 Check Digit Verification Enable Code 128 Check Digit Verification * Disable Code 128 Check Digit Verification Code 128 Check Digit Transmission Transmit Code 128 Check Digit * Do Not Transmit Code 128 Check Digit 51
Code128 Length Scan Max. Code Length（2 Digits；00~99；99*） Scan Min.
UCC/EAN 128 Enable/Disable UCC/EAN 128 Enable* Disable UCC/EAN 128 Check Digit Verification Enable* Disable UCC/EAN 128 Check Digit Transmission Transmit UCC/EAN 128 Check Digit * Do Not Transmit UCC/EAN 128 Check Digit 53
UCC/EAN 128 Length Scan Max. Code Length（2 Digits；00~99；99*） Scan Min.
Code 39 Enable/Disable Code 39 Enable* Disable Code 39 Check Digit Verification Enable Disable* Code 39 Check Digit Transmission Transmit Code 39 Check Digit Do Not Transmit Code 39 Check Digit * 55
Code 39 Full ASCII Conversion Enable Code 39 Full ASCII Disable Code 39 Full ASCII * Start/End transmission Enable Code 39 Start/End transmission Disable Enable Code 39 Start/End transmission * Convert Code 39 to Code 32 Enable Convert Code 39 to Code 32 Disable Convert Code 39 to Code 32* 56
Code 32 Prefix “A” transmission Enable Code 32 Prefix “A” transmission Disable Code 32 Prefix “A” transmission* “*” as data character Enable Disable* Code39 Length Scan Max. Code Length（2 Digits；00~99；99*） Scan Min.
Code ID setting（ ‘a’） Scan Code ID（2 Digits；00~FF； 61*） Insert String 1 Selection Scan Insert String 1（1 Digit；0~6；0*） Insert String 2 Selection Scan Insert String 2（1 Digit；0~6；0*） 58
Code 93 Enable/Disable Code 93 Enable* Disable Code 93 Check Digit Verification Enable Code 93 Check Digit Verification * Disable Code 93 Check Digit Verification Code 93 Check Digit Transmission Transmit Code 93 Check Digit ** Do Not Transmit Code 93 Check Digit 59
Code 93 Full ASCII Conversion Enable Code 93 Full ASCII Disable Code 93 Full ASCII * Code 93 Length Scan Max. Code Length（2 Digits；00~99；99*） Scan Min.
Code ID setting（ ‘h’） Scan Code ID（2 Digits；00~FF； 68*） Insert String 1 Selection Scan Insert String 1（1 Digit；0~6；0*） Insert String 2 Selection Scan Insert String 2 （1 Digit；0~6；0*） 61
Interleaved 2 of 5 Interleaved 2 of 5 Data digits (Variable) Check digit (one bit ,optional) Enable/Disable Format of Interleaved Enable* Disable Interleaved 2 of 5 Check Digit Verification Enable Disable* 62
Interleaved 2 of 5 Check Digit Transmission Transmit Interleaved 2 of 5 Check Digit Do Not Transmit Interleaved 2 of 5 Check Digit * Interleaved 2 of 5 Length Scan Max. Code Length（2 Digits；00~99；99*） Scan Min.
Code ID setting（ ‘i’） Scan Code ID（2 Digits；00~FF； 69*） Insert String 1 Selection Scan Insert String 1（1 Digit；0~6；0*） Insert String 2 Selection Scan Insert String 2（1 Digit；0~6；0*） 64
Industrial 2 of 5 Enable/Disable Industrial 2 of 5 Enable* Disable Industrial 2 of 5 Check Digit Verification Enable Disable * 65
Industrial 2 of 5 Check Digit Transmission Transmit Industrial 2 of 5 Check Digit Do Not Transmit Industrial 2 of 5 Check Digit * Industrial 2 of 5 Length Scan Max. Code Length（2 Digits；00~99；99*） Scan Min.
Code ID setting（ ‘j’） Scan Code ID（2 Digits；00~FF； 6A*） Insert String 1 Selection Scan Insert String 1（1 Digit；0~6；0*） Insert String 2 Selection Scan Insert String 2（1 Digit；0~6；0*） 67
Matrix 2 of 5 Enable/Disable Matrix 2 of 5 Enable* Disable Matrix 2 of 5 Check Digit Verification Enable Disable * Matrix 2 of 5 Check Digit Transmission Transmit Matrix 2 of 5 Check Digit Do Not Transmit Matrix 2 of 5 Check Digit * 68
Matrix 2 of 5 Length Scan Max. Code Length（2 Digits；00~99；99*） Scan Min.
Codabar Enable/Disable Codabar Enable* Disable Codabar Check Digit Verification Enable Disable* Codabar Check Digit Transmission Transmit Codabar Check Digit Do Not Transmit Codabar Check Digit * 70
Start/End type ABCD/ABCD * abcd/abcd ABCD/TN*E abcd/tn*e Start/End transmission Enable Disable * 71
Codarbar Length Scan Max. Code Length（2 Digits；00~99；99*） Scan Min.
Code 11 Enable/Disable Code 11 Enable* Disable Code 11 Check Digit Verification Enable 1bit check Digit * Enable 2 bit check Digit Disable check Digit 73
Code 11 Check Digit Transmission Transmit Code11 Check Digit Do Not Transmit Code11 Check Digit * Code 11 Length Scan Max. Code Length（2 Digits；00~99；99*） Scan Min.
Insert String 1 Selection Scan Insert String 1（1 Digit；0~6；0*） Insert String 2 Selection Scan Insert String 2（1 Digit；0~6；0*） MSI/Plessey Enable/Disable MSI/Plessey Enable *0 Disable 75
MSI/Plessey Check Digit Verification Enable 1 digit（Mod10） Enable 2 digit（Mod10/10） Enable 2 digit（Mod11/10） Disable* MSI/Plessey Check Digit Transmission Transmit MSI/Plessey Check Digit Do Not Transmit MSI/Plessey Check Digit * 76
MSI/Plessey Length Scan Max. Code Length（2 Digits；00~99；99*） Scan Min.
UK/Plessey Check digit verification: The UK/Plessey has two optional check digits. The check digit 1 and check digit 2 will be calculated as the sum module 10 or 11 of the data digits.
UK /Plessey Check Digit Transmission Transmit UK /Plessey Check Digit Do Not Transmit UK /Plessey Check Digit * UK/Plessy Lenght Scan Max. Code Length（2 Digits；00~99；99*） Scan Min.
Code ID setting（‘u’） Scan Code ID（2 Digits；00~FF； 75*） Insert String 1 Selection Scan Insert String 1（1 Digit；0~6；0*） Insert String 2 Selection Scan Insert String 2（1 Digit；0~6；0*） 80
GS1 DataBar (GS1 DataBar Truncated) GS1 DataBar Truncated is structured and encoded the same as the standard GS1 DataBar format, except its height is reduced to a 13 modules minimum; while GS1 DataBar should have a height greaterthan or equal to 33 modules.
Code ID setting（‘r’） Scan Code ID（2 Digits；00~FF； 72*） Insert String 1 Selection Scan Insert String 1（1 Digit；0~6；0*） Insert String 2 Selection Scan Insert String 2（1 Digit；0~6；0*） 82
GS1 DataBar Limited Enable/Disable GS1 DataBar Limited Enable* Disable Conversion Convert GS1 DataBar Limited UCC/EAN 128 Convert GS1 DataBar Limited UPC-A OR EAN-13 Disable Conversion* 83
Code ID setting（‘s’） Scan Code ID（2 Digits；00~FF； 73*） Insert String 1 Selection Scan Insert String 1（1 Digit；0~6；0*） Insert String 2 Selection Scan Insert String 2（1 Digit；0~6；0*） 84
GS1 DataBar Expanded Enable/Disable GS1 DataBar Expanded Enable* Disable Conversion Convert GS1 DataBar Expanded UCC/EAN 128 Disable Conversion* GS1 DataBar Expanded Lenght Scan Max. Code Length（2 Digits；00~99；99*） Scan Min.
Scan Code ID（2 Digits；00~FF； 70*） Insert String 1 Selection Scan Insert String 1（1 Digit；0~6；0*） Insert String 2 Selection Scan Insert String 2（1 Digit；0~6；0*） Advanced Bar Code Data Formatting Format of barcode data transmission： Prefix Code Preamble Code Code 86 Code Code Postamble Suffix
name ID length data Suffix Quick Setup CR *L0 LF CR & LF None Prefix Transmit Prefix: 87 ID
Do Not Transmit Prefix * Scan Prefix（0~16 Chars，2 Digits /Char；00~FF； 00*） Suffix The default Suffix is CR。 Transmit Suffix * Do Not Transmit Suffix Scan Suffix（0~22 Chars，2 Digits /Char；00~FF； 00*） Preamble Transmit Preamble Do Not Transmit Preamble * 88
Scan preamble（0~16 Chars，2 Digits /Char；00~FF； 00*） Postamble Transmit Postamble Do Not Transmit Postamble * Scan Postamble（0~16 Chars，2 Digits /Char；00~FF； 00*） Code ID Transmit Proprietary ID Transmit AIM ID 89
Do Not Transmit Code ID* Code ID position Before code data After code data * Code name transmission Transmit Code name Do Not Transmit Code name * Code length transmission Transmit Code length Do Not Transmit Code length * 90
Case conversion: The characters within code data or the whole output string can be set in either upper case or lower case Disable* Upper (data only) Lower (data only) Upper (whole string) Lower (whole string) Insert String G1 Setting Scan Inert String G1（0~16 Chars，2 Digits /Char；00~FF； 00*） Scan the Position of G1（2 Digits；00~99； 00*） 91
Insert String G2 Setting Scan Inert String G2（0~16 Chars，2 Digits /Char；00~FF； 00*） Scan the Position of G2（2 Digits；00~99； 00*） Insert String G3 Setting G3 is also used as the string to be replaced when the replace function is enabled. Scan Inert String G3（0~16 Chars，2 Digits /Char；00~FF； 00*） Scan the Position of G3（2 Digits；00~99； 00*） Insert String G4 Setting G4 is also used as the string to replace G3 in a bar code data when the replace function is enabled.
Scan the Position of G4（2 Digits；00~99； 00*） FN1 substitution string setting The FN1 character (0x1D) in an UCC/EAN128 barcode, or a Code 128 barcode, or a GS1 DataBar barcode can be substituted with a defined string. Enable FN1 Substitution Disable FN1 Substitution * Scan FN1 substitution string setting（0~4 Chars，2 Digits /Char；00~FF； 00*） Truncate leading G5 String setting By setting G5, a defined leading character or string can be truncated. G5 can also be set to be repeated.
Truncate leading G5 string setting (2 Digits；00~99； 01*） Truncate ending G6 string setting By setting G6, a defined ending character or string can be truncated. G5 can also be set to be repeated. Scan G6 String（0~16 Chars，2 Digits /Char；00~FF； 00*） Scan Repeat of a G6 String (2 Digits；00~99； 01*） Replace String Setting Replace G3 string to G4 string in barcode data.
Disable * Test Bar Code 95
Appendix 2 Default setting for each barcode Table 2 Default setting for each barcode Code type Read Check Check digit Min.
ISBN/ISSN1 √ √ √ (13) e ]Em UPC-A √ √ √ (12) b ]Em UPC-E √ √ √ (8) c ]Em Code 128 √ √ - 1 g ]Cm UCC/EAN 128 √ √ - 1 q ]Cm Code 93 √ √ - 1 h ]Gm Code 39 √ - - 1 a ]Am Code 11 √ √ - 4 m - Interleaved 2 of 5 √ - - 6 i ]Im Industrial 2 of 5 √ - - 4 j ]Im Matrix 2 of 5 √ - - 6 x ]Im China Post √ √ - (11) y ]Im Codabar √ - - 5 k ]Fm MSI/Plessey √ - - 4 f ]Mm UK/Plessey √ - - 1 u ]Mm GS1 DataBar √ - - (16)
1 The settings for ISBN/ISSN and EAN-13 must be the same. 2 Fixed-length barcodes. 3 The settings for GS1 DataBar Truncated and GS1 DataBar must be the same.
Long-Range series 99
Appendix 6 ASCII Table Table 3 Function Keys H L P/S2 keyboard/USB 0 1 RS-232 0 1 NUL DLE 0 Null 1 Up F1 SOH DC1 2 Down F2 STX DC2 3 Left F3 ETX DC3 4 Right F4 EOT DC4 5 PgUp F5 ENQ NAK 6 PgDn F6 ACK SYN F7 BEL ETB 7 8 Bs F8 BS CAN 9 Tab F9 HT EM F10 LF SUB A B Home Esc VT ESC C End F11 FF FS D Enter F12 CR GS E Insert Ctrl+ SO RS F Delete Alt+ SI US 101
Table 4 Chars H 2 3 4 5 6 7 0 SP 0 @ P ` p 1 ! 1 A Q a q 2 “ 2 B R b r 3 # 3 C S c s 4 $ 4 D T d t 5 % 5 E U e u 6 & 6 F V f v 7 ‘ 7 G W g w 8 （ 8 H X h x 9 ） 9 I Y i y A * ： J Z j z B + ; K [ k { C , < L \ l | D - = M ] m } E .
Appendix 8 Parameter bar code 0 %N0 1 %N1 2 3 4 5 6 7 8 9 103
A B C D E F Finish Setting 104
