Design Guide REVISED 11/2021
Designer Refrigeration Designer Refrigeration With custom front panels and hardware, Sub-Zero Designer columns, tall, and drawer models disappear into the decor. Designer units fit flush with cabinetry, making Designer refrigeration as practical and beautiful in the master suite, bar, or theatre room as in the kitchen. Model ID-24RO, approved for outdoor installations, is ideal for any outdoor kitchen.
Designer Refrigeration Overall Dimensions COLUMN COLUMN W 24" (610) 4 1/2" (114) A B 18" Column 18" (457) 21/2" (64) 161/2" (419) 24" Column 24" (610) 4" (102) 221/2" (572) 30" Column 30" (762) 55/8" (143) 281/2" (724) 36" Column 36" (914) 71/4" (184) 341/2" (876) IMPORTANT NOTE: Overall dimensions do not include panels or handles. Dimensions will vary with panel thickness. 69 1/2" 84"* (2134) W (1765) 3 5/8" (92) HEIGHT DIMENSIONS ± 1/2" (13) A 13/4" (45) B subzero.
Designer Refrigeration Overall Dimensions TALL TALL W 24" (610) 4 1/2" (114) W A B 30" Tall 30" (762) 55/8" (143) 281/2" (724) 36" Tall 36" (914) 71/4" (184) 341/2" (876) IMPORTANT NOTE: Overall dimensions do not include panels or handles. Dimensions will vary with panel thickness. 44 7/8" 84"* (2134) (1140) 3/8" (10) 13 5/16" (338) 3/8" (10) 10 9/16" (268) 3 5/8" (92) HEIGHT DIMENSIONS ± 1/2" (13) A 13/4" (45) 17 3/4" (451) 46 B | Sub-Zero Customer Care 800.222.
Designer Refrigeration Overall Dimensions DRAWER DRAWER W 24" (610) 1/4" (6) 13 5/16" (338) 3/8" (10) 34 1/2"* (876) 10 9/16" (268) HEIGHT DIMENSIONS ± 1/2" (13) W 24" Drawer 24" (610) 27" Drawer 27" (686) 30" Drawer 30" (762) 36" Drawer 36" (914) IMPORTANT NOTE: Overall dimensions do not include panels or handles. Dimensions will vary with panel thickness. 3 5/8" (92) 17 3/4" (451) subzero.
Designer Refrigeration Opening Dimensions DESIGNER SERIES OPENING DIMENSIONS COLUMN / TALL 25" (635) OPENING DEPTH 25 3/4" (654) FOR OUTDOOR MODEL 18" Column 24" Column 30" Column / Tall 36" Column / Tall TOP VIEW DRAWER 24" Drawer 27" Drawer 30" Drawer 36" Drawer W* H 18" (457) 24" (610) 30" (762) 36" (914) 84" (2134) 84" (2134) 84" (2134) 84" (2134) W* H 24" (610) 27" (686) 30" (762) 36" (914) 341/2" (876) 341/2" (876) 341/2" (876) 341/2" (876) *For stainless steel side panel accessory, add
Designer Refrigeration Electrical Requirements Plumbing Requirements Locate the electrical supply within the shaded area shown in the illustration and chart below. A separate circuit servicing only this appliance is required. Locate the water supply line within the shaded area shown in the illustration below. Connect the water supply line to the house supply with an easily accessible shut-off valve. Do not use self‑piercing valves.
Designer Refrigeration Stainless Steel Panels Custom Panels The outdoor model requires the use of Sub-Zero stainless steel outdoor accessory panels. Stainless steel panels and handles are available through an authorized Sub‑Zero dealer. For local dealer information, visit the find a showroom section of our website, subzero.com. For all models, door panels and handles must be provided. Refer to the Panel Requirements chart and Typical Panel Dimensions.
Designer Refrigeration Custom Panels TYPICAL PANEL DIMENSIONS DOOR PANEL HEIGHT The height of the custom door panel can extend beyond the typical panel height, provided it does not exceed the weight limit. Refer to the illustration below.
Designer Refrigeration Custom Panels Standard Handles TOE KICK CLEARANCE Optional stainless steel tubular and pro handles are avail able through an authorized Sub-Zero dealer. For local dealer information, visit the find a showroom section of our website, subzero.com. Indoor Models Only: The height of the toe kick area can extend beyond the typical toe kick height, provided it does not exceed the dimensions in the illustration below.
Designer Refrigeration Maximum Door Opening FULL-SCALE TEMPLATE As the panel width and/or depth increases, so does the potential for panel interference. Interference may be minimized by using the 90° door stop. 3/4" (19) PANEL DOOR OPEN MAXIMUM 105° 1/8" (3) REVEAL POTENTIAL INTERFERENCE DOOR CLOSED 3/4" (19) PANEL ADJACENT CABINETRY POTENTIAL INTERFERENCE 0" 1" (25) SCALE Maximum door opening (top view) subzero.
Wine Storage Wine Storage Wine finds a well-deserved place of honor in a Sub-Zero wine storage unit. Every detail is designed to ensure better wine preservation. Cherrywood-faced racks, soft lighting, custom cabinetry if desired—Sub-Zero helps make a wine collection an element of beauty in the home. WINE STORAGE MODELS DEU2450W IW-18 BW-30 54 | Sub-Zero Customer Care 800.222.
Wine Storage Overall Dimensions MODEL DEU2450W 23 1/8" (587) 24" (610) IMPORTANT NOTE: Overall dimensions do not include panels or handles. Dimensions will vary with panel thickness. 34 1/2" (876) HEIGHT DIMENSIONS ± 1/2" (13) 9 5/8" (245) 26 1/2" (673) subzero.
Wine Storage Opening Dimensions MODEL DEU2450W The depth of each model is 231/8" (587). Allow for panel thickness when planning the finished opening depth. A minimum 31/2" (89) finished return is required on all sides of the opening. Framed cabinets require additional finished filler material behind the face frame for a proper installation. Refer to the illustration.
Wine Storage Dual Installation MODEL DEU2450W If two units are installed side by side, a dual installation kit may be required. Installations without a custom filler strip require a dual installation kit. If a dual installation kit is not specified, a 2" (51) filler strip is recommended between the units. Dual installations without a filler strip can only be accomplished using two units with opposite hinges. Refer to the illustrations below.
Wine Storage Overall Dimensions COLUMN COLUMN W 84"* (2134) 24" (610) B IW-18 18" (457) 21/2" (64) 161/2" (419) IW-24 24" (610) 4" (102) 221/2" (572) IW-30 30" (762) 55/8" (143) 281/2" (724) 69 1/2" IMPORTANT NOTE: Overall dimensions do not include panels or handles. Dimensions will vary with panel thickness. (1765) 3 5/8" (92) A 13/4" (45) B | A 4 1/2" (114) HEIGHT DIMENSIONS ± 1/2" (13) 58 W Sub-Zero Customer Care 800.222.
Wine Storage Overall Dimensions TALL TALL IW-30R, IW-30CI W W A B 30" (762) 55/8" (143) 281/2" (724) 24" (610) 4 1/2" (114) IMPORTANT NOTE: Overall dimensions do not include panels or handles. Dimensions will vary with panel thickness. 44 7/8" 84"* (2134) (1140) 3/8" (10) 13 5/16" (338) 3/8" (10) 10 9/16" (268) 3 5/8" (92) HEIGHT DIMENSIONS ± 1/2" (13) A 13/4" (45) 17 3/4" (451) B subzero.
Wine Storage Opening Dimensions DESIGNER WINE STORAGE OPENING DIMENSIONS 25" (635) OPENING DEPTH W* 18" Column 18" (457) 24" Column 24" (610) 30" Column / Tall 30" (762) *For stainless steel side panel accessory, add 1" (25) per panel to opening width. TOP VIEW The depth of each Designer (IW) model is 24" (610). Allow for panel thickness when planning the finished opening depth. A minimum 31/2" (89) finished return is required on all sides of the opening.
Wine Storage Overall Dimensions MODEL BW-30 26 3/16" (665) 30" (762) IMPORTANT NOTE: Overall dimensions are based on the stainless steel model. For flush inset applications, add 1/2" (13) to door clearance dimensions. 84" (2134) 73 3/4" (1873) HEIGHT DIMENSIONS ± 1/2" (13) 4" (102) 23 7/8" (606) 23 7/8" (606) 17" (432) 311/4" (796) 2 3/8" (60) subzero.
Wine Storage Opening Dimensions MODEL BW-30 STANDARD INSTALLATION 24" (610) OPENING DEPTH 3/4" (19) 3 1/2" (89) TYPICAL FINISHED RETURN TOP VIEW W FRAMELESS CABINETRY 3/4" (19) 3 1/2" (89) FINISHED RETURN 83 3/4" (2127) OPENING HEIGHT SIDE VIEW W TYPICAL FILLER W OPENING WIDTH FRAMED CABINETRY FRONT VIEW NOTE: 3 1/2" (89) finished returns will be visible and should be finished to match cabinetry. Shaded line represents profile of unit.
Wine Storage Opening Dimensions MODEL BW-30 FLUSH INSET INSTALLATION 26 3/16" (665) FLUSH INSET DEPTH 5 11/16" 3 1/2" 2 3/16" (56) (89) (145) FINISHED RETURN FINISHED CLEATS TOP VIEW CLEAT 3/4" (19) TYPICAL W FRAMELESS CABINETRY 11/4" 1/4" (6) (32) 5 11/16" 3 1/2" (89) (145) FINISHED RETURN 84" (2134) FLUSH INSET HEIGHT SIDE VIEW W CLEAT FILLER 3/4" (19) TYPICAL W FLUSH INSET WIDTH FRAMED CABINETRY FRONT VIEW NOTE: 3 1/2" (89) finished returns and shaded areas will be visible and s
Wine Storage Opening Dimensions MODEL BW-30 DUAL STANDARD INSTALLATION 24" (610) OPENING DEPTH 3/4" (19) 3 1/2" (89) TYPICAL FINISHED RETURN TOP VIEW W FRAMELESS CABINETRY 3/4" (19) 3 1/2" (89) FINISHED RETURN 83 3/4" (2127) OPENING HEIGHT SIDE VIEW W OPENING WIDTH TYPICAL FILLER W FRAMED CABINETRY FRONT VIEW NOTE: 3 1/2" (89) finished returns will be visible and should be finished to match cabinetry. Shaded line represents profile of unit.
Wine Storage Opening Dimensions MODEL BW-30 DUAL FLUSH INSET INSTALLATION 26 3/16" (665) FLUSH INSET DEPTH (56) CLEAT 5 11/16" 3 1/2" 2 3/16" 3/4" (19) (89) (145) FINISHED RETURN FINISHED CLEATS TOP VIEW TYPICAL W FRAMELESS CABINETRY 11/4" 1/4" (6) (32) CLEAT 5 11/16" 3 1/2" (89) (145) FINISHED RETURN 84" (2134) FLUSH INSET HEIGHT SIDE VIEW W FLUSH INSET WIDTH FILLER 3/4" (19) TYPICAL W FRAMED CABINETRY FRONT VIEW NOTE: 3 1/2" (89) finished returns and shaded areas will be visibl
Wine Storage Electrical Requirements Locate the electrical supply within the shaded area shown in the illustration for your specific model. For Designer (IW) models, also refer to the chart. A separate circuit servicing only this appliance is required. A ground fault circuit interrupter (GFCI) is not recommended and may cause interruption of operation.
Wine Storage Plumbing Requirements MODEL IW-30CI PLUMBING REQUIREMENTS For model IW-30CI, locate the water supply line within the shaded area shown in the illustration below. Connect the water supply line to the house supply with an easily accessible shut-off valve. Do not use self‑piercing valves. The water supply line must not interfere with installation of the anti-tip bracket. Water Supply Pressure Excess Line for Connection 1/4" OD copper, braided stainless steel, or PEX tubing 35–120 psi (2.4–8.
Wine Storage Custom Panels Custom Panel—DEU2450W For all models excluding stainless steel, door panels and handles must be provided. Refer to the panel requirements and custom panel dimensions charts for your specific model and design application. For model DEU2450W, the custom door panel will attach directly to the door frame with screws through a series of pre-drilled holes. Refer to the following charts for panel requirements and dimensions. Do not install a solid panel on a glass door unit.
Wine Storage Custom Panel—DEU2450W TOE KICK CLEARANCE MAXIMUM DOOR OPENING The height of the toe kick area can extend beyond the typical toe kick height, provided it does not exceed the dimensions in the illustration below. For questions regarding the installation, call Sub‑Zero Customer Care at 800-222-7820. As the panel width and/or depth increases, so does the potential for panel interference. Interference may be minimized by using the 90° door stop.
Wine Storage Custom Panel—Designer For Designer (IW) models, custom door panels and handle hardware must be provided. Refer to the Panel Requirements chart and Typical Panel Dimensions. Do not install a solid panel on the glass door unit. A solid door is available as a sales accessory through an authorized Sub-Zero dealer. The thickness of the custom panel can vary. A minimum 5/8" (16) thick panel is required, but the thickness can be increased provided it does not exceed the weight limit.
Wine Storage Custom Panel—Designer TYPICAL PANEL DIMENSIONS DUAL INSTALLATION For dual installations, refer to the illustration for panel height and the chart below for panel width.
Wine Storage Custom Panel—Designer DOOR PANEL HEIGHT TOE KICK CLEARANCE The height of the custom door panel can extend beyond the typical panel height, provided it does not exceed the weight limit. Refer to the illustration below. The height of the toe kick area can extend beyond the typical toe kick height, provided it does not exceed the dimensions in the illustration below.
Wine Storage Custom Panel—BW-30 FRAMED FRAMED PANEL DIMENSIONS The framed application is an overlay model with framed design features. It is not a separate model. If the custom panel is thinner than 1/4" (6), a filler material must be added to achieve a proper fit. If the panel is thicker than 1/4" (6), rout an edge around the panel or mount the custom panel on a sheet of 1/4" (6) thick material and insert into the channel.
Wine Storage Custom Panel—BW-30 OVERLAY OVERLAY PANEL DIMENSIONS Overlay panels are typically created by combining a 3/4" (19) custom panel, a .10" (3) spacer panel, and a 1/4" (6) backer panel. Refer to the illustrations below.
Wine Storage Custom Panel—BW-30 FLUSH INSET FLUSH INSET PANEL DIMENSIONS The flush inset application is an overlay model with flush inset panels. It is not a separate model. The flush inset design allows custom panels to be installed flush with adjacent cabinets. Similar to overlay, flush inset panels are typically created by combining a 3/4" (19) custom panel, a .10" (3) spacer panel, and a 1/4" (6) backer panel. Refer to the illustrations for overlay panels on the previous page.
5/16" (8) Wine Storage 5/8" (16) TOP VIEW 1/2" (13) Custom Panel—BW-30 BACKER SPACER FLUSH INSET PANEL OFFSET CABINETRY 5/8" (16) DOOR A Grille Top B Grille Bottom / Door Top C Door Bottom D 1/2" (13) TOP VIEW DOOR CABINETRY 1/4" (6) 5/16" (8) 5/8" (16) GRILLE SIDE VIEW 5/16" (3) (8) GRILLE CABINETRY 5/32" 5/16" (4) (8) SIDE VIEW 5/16" (8) 1/2" (13) 1/8" (3) 1/4" (6) SIDE VIEW REVEAL DOOR GRILLE 5/16" (8) 5/32" (4) 5/16" (8) 1/2" (13) 1/2" (13) 3/32" 5/16" (2) (8) 1/8" 5S
Wine Storage Custom Panel—BW-30 DUAL INSTALLATIONS DUAL FLUSH INSET PANEL DIMENSIONS A dual installation kit may be required if two models BW-30 or a model BW-30 and a Classic unit are installed side by side. Installations without a custom filler strip require a dual installation kit. If a dual installation kit is not specified, a 2" (51) filler strip is recommended between the units. Dual installations without a filler strip can only be accomplished using two 84" (2134) units with opposite hinges.
Wine Storage TOP VIEW TOP VIEW DOOR / DRAWER / GRILLE BACKER SPACER DOOR CABINETRY DOOR TOP VIEW 5 /16" (8) Custom Panel—BW-30 DUAL FLUSH INSET PANEL 1/2" (13) 5/8" (16) OFFSET 1/8" (3) BACKER SPACER BACKER CABINETRY SPACER ILLUS Door (hinge) / Grille Sides A Door (handle) Sides B Grille Top Door Bottom GRILLE 1/4" (6) CABINETRY 1/2" (13) D E 1/8" 5/16" (3) (8) BACKER 1/2" (13) CABINETRY 5/8" SPACER (16) DOOR TOP VIEW DUAL TRIM 5/16" (8) 1/2" (13) DOOR DOOR TOP VIEW DOOR
Wine Storage Custom Panel—BW-30 SIDE PANEL 24" (610) The custom side panel must be a minimum of 24" (610) deep and 1/2" (13) thick. Routing will be necessary for the side panel to fit flush against the side of the unit. Refer to the illustrations. When installing model BW-30 with a custom side panel, an accessory kit is required. Stainless steel and white enamel side panels are available for an 84" (2134) finished height through an authorized Sub-Zero dealer.
Wine Storage Standard Handles Optional stainless steel tubular and pro handles are avail able through an authorized Sub-Zero dealer. For local dealer information, visit the find a showroom section of our website, subzero.com. Refer to the chart below for standard handle lengths for wine storage models.
Wine Storage Wine Rack Wood Facing FULL-SCALE TEMPLATE WOOD FACING WIDTH The natural cherrywood facing on wine storage racks can be stained and sealed, or replaced with wood more complementary to surrounding cabinetry. Refer to the full-scale templates below for the profile dimensions of the wood facing and the charts for the width.
Wine Storage Framed Panel—BW-30 FULL-SCALE TEMPLATE OPTIONAL EXTENDED FULL-LENGTH HANDLE STANDARD FULL-LENGTH HANDLE 2" 1" (51) (25) 3" (76) 11/4" (32) PANEL 1" (25) PANEL 3/4" (19) PANEL 1/2" (13) PANEL 1/4" (6) FRAMED PANEL DOOR Framed panel thickness 82 | Sub-Zero Customer Care 800.222.
Wine Storage Overlay / Flush Inset Panels—BW-30 FULL-SCALE TEMPLATE Overlay and flush inset panels must be a minimum of 5/8" (16) thick to support mounting the handle. Panel thickness does not include the backer and spacer panels. Mount the handle close to the opening edge of the door. DEPTH OF TUBULAR AND PRO HANDLES 1" 2" (25) (51) 3" (76) 11/4" (32) PANEL 1" (25) PANEL 3/4" (19) PANEL .10" (3) SPACER PANEL 1/4" (6) BACKER PANEL DOOR Overlay and flush inset panel thickness subzero.
Wine Storage Overlay Application—BW-30 FULL-SCALE TEMPLATE 237/8" (606) TO REAR OF UNIT OVERALL WIDTH OF UNIT 0" (0) 1/4" (6) 1/2" (13) 3/4" (19) 1" (25) 11/4" (32) 11/2" (38) 13/4" (44) 2" (51) 21/4" (57) 21/2" (63) 23/4" (70) 3" (76) 31/4" (83) 31/2" (89) 1" (25) THICK PANEL 3/4" (19) THICK OVERLAY PANEL (TYPICAL) 1/4" (6) BACKER PANEL 0" 1" (25) SCALE 90° door opening (top view) 84 | Sub-Zero Customer Care 800.222.
Wine Storage Flush Inset Application—BW-30 FULL-SCALE TEMPLATE 24" (610) TO BACK WALL For panels thicker than 3/4" (19), a 90° door stop may be required to prevent interference with adjacent cabinets. 1 1/4" (32) 2 3/16" (56) ASSUMES 3/4" (19) FLUSH INSET PANEL THICKNESS 1" (25) THICK PANEL 3/4" (19) THICK FLUSH INSET PANEL (TYPICAL) 1/4" (6) BACKER PANEL 0" 1" (25) SCALE 110° door opening (top view) subzero.
Wine Storage FILLER STRIP 11/4" (32) APPROX PROFILE OF STAINLESS STEEL WRAPPED DOOR AND HANDLE Dual Standard Installation—BW-30 FULL-SCALE TEMPLATE Typical framed, overlay, or stainless steel dual installation with filler strip at maximum 110° door opening. Panel thickness may require a 90° door stop. 0" 1" (25) SCALE Dual standard installation (top view) 86 | Sub-Zero Customer Care 800.222.
Wine Storage FILLER STRIP 1 1/2" (38) 1/2" (13) PROFILE OF 3/4" (19) FLUSH INSET PANEL AND TUBULAR HANDLE Dual Flush Inset Installation—BW-30 DOOR CLOSED DOOR OPEN 110° FULL-SCALE TEMPLATE Typical flush inset dual installation with filler strip at maximum 110° door opening. Panel thickness may require a 90° door stop. 0" 1" (25) SCALE Dual flush inset installation (top view) subzero.
SUBZERO.
