M.2 NGFF SSD to 2.5in SATA Adapter SAT2M2NGFF25 *actual product may vary from photos DE: Bedienungsanleitung - de.startech.com FR: Guide de l'utilisateur - fr.startech.com ES: Guía del usuario - es.startech.com IT: Guida per l'uso - it.startech.com NL: Gebruiksaanwijzing - nl.startech.com PT: Guia do usuário - pt.startech.com For the most up-to-date information, please visit: www.startech.
FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Table of Contents Introduction.............................................................................................1 Packaging Contents.................................................................................................................................. 1 System Requirements............................................................................................................................... 1 Assembled Adapter View................................................................
Introduction Packaging Contents • 1x M.2 NGFF SSD to 2.5” SATA Adapter • 1x SSD mounting kit • 1x Mini Screw driver • 1x Instruction manual System Requirements • M.
Assembled Adapter View Assembled Adapter View 1. Top mounting holes 2. Side mounting holes 3. SATA DATA & Power Combo (7+15 pin) 4. HDD plate 1 5. HDD plate mounting holes 5 1 5 4 5 1 2 3 1 2 5 Open Adapter View 1. M.2 (NGFF) SSD Connector 2. Drive installation bracket 3. Drive length adjustment holes 4.
M.2 NGFF SSD Installation WARNING: SSD Drives and storage adapters require careful handling. If you are not careful with your SSD Drive, lost data may result. Always handle your drive with caution. Be sure that you are properly grounded by wearing an anti-static strap when handling computer components or discharge yourself of any static electricity build-up by touching a large grounded metal surface (such as the computer case) for several seconds. 1.
2. Determine if the drive installation bracket requires relocating by assessing your drive length. The board is labeled with the respective drive types for length but if your drive type is unknown,place your SSD next to the M.2 (NGFF) SSD connector, note which drive installation hole matches the height of your SSD. If the bracket is already installed in the correct position please proceed to step 4. 3.
Note: It may require a small prying tool or tweezers to carefully remove the board. b) Remove the nut holding the bracket in place on the reverse side using a small set of plyers (Not included).
c) Reseat the drive installation bracket in the drive installation hole that matches your SSD. Replace the removed nut on the reverse side by using a small set of plyers (not included).
d) Carefully reseat the main board inside the adapter enclosure. 4. Using the included screw driver. Remove the screw located in the front of the hard drive installation bracket.
5. Slide the M.2 connector on the SSD into the M.2 receprical connector on the SAT2M2NGFF25. Note: The connector on your M.2 SSD is keyed so the drive will only fit one way. 6. Press the drive down toward the drive mounting bracket, and drive the removed screw through the mounting hole on your SSD drive and into the drive mounting bracket using a Philips head screw driver.
7. Replace the HDD plate on the bottom of the adapter case, and drive four of the included case screws into the HDD plate mounting holes on the HDD plate, into the HDD plate mounting holes on the adapter. 8. The SSD has now been installed, and is ready to be implemented in your 2.5” SATA drive application. Refer to the manual for your SATA host device for installation instructions. The side mounting holes and included screw kit may or may not be required to assist in your installation.
Hard Drive Initialization If the M.2 NGFF SSD is new or otherwise blank, it may need to be initialized and formatted before use. Follow the steps below in a Windows interface to initialize the drive. 1. From the main Windows desktop, right-click on “My Computer” (“Computer” in Vista/ 7 / 8), then select Manage. In the new Computer Management window, select Disk Management from the left window panel. 2. A dialog window should automatically appear, asking you to initialize the drive.
Technical Support StarTech.com’s lifetime technical support is an integral part of our commitment to provide industry-leading solutions. If you ever need help with your product, visit www.startech.com/support and access our comprehensive selection of online tools, documentation, and downloads. For the latest drivers/software, please visit www.startech.com/downloads Warranty Information This product is backed by a two year warranty. In addition, StarTech.
Hard-to-find made easy. At StarTech.com, that isn’t a slogan. It’s a promise. StarTech.com is your one-stop source for every connectivity part you need. From the latest technology to legacy products — and all the parts that bridge the old and new — we can help you find the parts that connect your solutions. We make it easy to locate the parts, and we quickly deliver them wherever they need to go. Just talk to one of our tech advisors or visit our website.
