SATA to 2.5in or 3.5in IDE Hard Drive Adapter for HDD Docks SAT2IDEADP *actual product may vary from photos DE: Bedienungsanleitung - de.startech.com FR: Guide de l'utilisateur - fr.startech.com ES: Guía del usuario - es.startech.com IT: Guida per l'uso - it.startech.com NL: Gebruiksaanwijzing - nl.startech.com PT: Guia do usuário - pt.startech.com For the most up-to-date information, please visit: www.startech.
FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Table of Contents Introduction.............................................................................................1 Packaging Contents.................................................................................................................................. 1 System Requirements............................................................................................................................... 1 Installation..........................................................................
Introduction The SAT2IDEADP SATA to IDE hard drive adapter enables you to use your 2.5-inch/3.5inch IDE-based (PATA) hard drives in most StarTech.com SATA-based HDD docking stations and drive duplicators. The SATA-IDE adapter features all-metal construction that ensures maximum durability, and is fully compatible with IDE hard drives up to ATA-133 (133MBps).
SATA Power connector SATA Data connector Instruction Manual 2
3.5” Hard Drive Mounting Points 2.5” Hard Drive Mounting Points Installation 3.5in Hard Drive Setup 1. If connecting a 3.5in (40-pin) IDE hard drive, connect the 40-pin IDE ribbon cable to the 40-pin connector on the inside of the SAT2IDEADP. 2. Connect the large 4-pin LP4 power cable to the small 4-pin SP4 floppy power connector on the inside of the SAT2IDEADP.
3. Connect the ribbon cable and power cable to the connectors on the IDE hard drive. 4. Place the IDE drive onto the back plate of the SAT2IDEADP adapter and fold/tuck the cables into the opening of the adapter. Slide the IDE drive towards the connectors until the mounting holes on the bottom of the drive line up with the mounting points on the back plate of the adapter. The edge of the IDE drive should be sitting almost flush with the edge of the adapter’s opening. Tuck in Cables Mounting Screws 5.
2.5in Hard Drive Setup 1. If connecting a 2.5in (44-pin) IDE hard drive, connect the 40-pin to 44-pin IDE ribbon cable to the 40-pin connector on the inside of the SAT2IDEADP. 2. Connect the small 4-pin SP4 floppy power cable from the ribbon cable into the SP4 connector on the inside of the SAT2IDEADP. 3. Connect the IDE hard drive to the 44-pin connector on the ribbon cable. 4. Place the IDE drive onto the back plate of the SAT2IDEADP adapter and fold/tuck the cables into the opening of the adapter.
Specifications Host Interface SATA revision 1.0 1 x 40-pin IDE male Connectors 1 x SP4 Power male Compatible Hard Drives 2.5in and 3.5in PATA (IDE) 66/100/133 hard drive LBA Support 48-bit Enclosure Material Metal Operating Temperature 5°C ~ 80°C (41°F ~ 176°F) Storage Temperature -40°C ~ 70°C (-40°F ~ 158°F) Humidity 8% ~ 90% RH Dimensions (LxWxH) 101.0mm x 78.0mm x 26.
Technical Support StarTech.com’s lifetime technical support is an integral part of our commitment to provide industry-leading solutions. If you ever need help with your product, visit www.startech.com/support and access our comprehensive selection of online tools, documentation, and downloads. For the latest drivers/software, please visit www.startech.com/downloads Warranty Information This product is backed by a two year warranty. In addition, StarTech.
Hard-to-find made easy. At StarTech.com, that isn’t a slogan. It’s a promise. StarTech.com is your one-stop source for every connectivity part you need. From the latest technology to legacy products — and all the parts that bridge the old and new — we can help you find the parts that connect your solutions. We make it easy to locate the parts, and we quickly deliver them wherever they need to go. Just talk to one of our tech advisors or visit our website.
