REMOVABLE SERIAL ATA DRIVE DRAWER 5.
FCC COMPLIANCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
1 Table of Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Installing the Hard Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Installing the Drive Bay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Installing the Caddy . . . . . .
2 Introduction Thank you for purchasing a StarTech.com 5.25” Serial ATA hard drive drawer. Now, you can quickly add and remove hard drives from your system without having to open your computer. Each unit consists of a bay portion that fits into your 5.25” drive bay and a removable caddy that holds your hard disk. Whether for using multiple operating systems, making high speed, high capacity backups, or minimizing downtime on mission-critical computers, StarTech.
3 Contents • 1 x drive caddy • 1 x drive bay • 2 x Keys to lock/unlock the drive • 1 x Bag of assorted screws Installation This section will guide you through the installation of your external drive case. Please read through the instructions carefully and complete each step in the order listed. Installing the Hard Drive NOTE: Before installing the hard disk in the case, make sure that you have properly configured your hard disk according to your hard disk manufacturer’s specifications. 1.
4 Installing the Drive Bay in the PC 1. Make sure that your system is unplugged and you are grounded. 2. Remove the side covers from your PC and remove the front cover from an available 5 1/4” drive bay (see your computer’s user manual for details, if necessary). 3. a) By default, DRW150SAT/DRW150SATBK is configured for use with a SATA II drive. If you wish to use a SATA (150) drive, move the switch on the rear panel to the rightmost position (as illustrated below).
5 Installing the Caddy in the Bay 1. With the handle lifted, slide the caddy into the bay until it is firmly seated. Lower the handle to click the caddy into its proper position. 2. Insert the key and turn clockwise to lock the drive into place and supply the drive with power. The drive will not function if the drawer has not been locked. Removing the Drive Drawer 1. Insert the key and turn counter-clockwise to unlock the drive drawer. 2. Lift the handle and gently pull the caddy out of the bay.
6 Technical Specifications Enclosure Dimensions Length W idth Height 7.5 inches (190 mm) 5.8 inches (147 mm) 1.6 inches (41 mm) Enclosure Construction Aluminum Hard Drive Compatibility Compatible with 3.5” Serial ATA Hard Drives Data Transfer Rate Up to 300 MBytes/sec. Power 15 pin Serial ATA power connector 4 pin power connector Safety Certifications CE Interface Serial ATA 1.0 Front Fan 1.5 inches x 0.
7 Technical Support The following technical resources are available for this StarTech.com product: On-line help: We are constantly adding new information to the Tech Support section of our web site. To access this page, click the Tech Support link on our homepage, www.startech.com. In the tech support section there are a number of options that can provide assistance with this product. FAQ - This tool provides quick answers to the top questions asked by our customers.
Revised: April 10, 2007
