OWNER’S MANUAL 6V PLUSH RIDE-ON THIS MANUAL CONTAINS IMPORTANT SAFETY, PERFORMANCE AND MAINTENANCE INFORMATION. READ THE MANUAL BEFORE TAKING YOUR FIRST RIDE OR ALLOWING YOUR CHILD TO RIDE YOUR NEW ELECTRIC RIDE- ON TOY. KEEP THE MANUAL HANDY FOR FUTURE REFERENCE. DO NOT RETURN TO STORE! QUESTIONS OR COMMENTS? 1-800-551-0032 FOR AGES 3+ MAXIMUM WEIGHT: 65 lb (29.5 kg) NOTE: Illustrations in this Manual are for reference purposes only and may not reflect the exact appearance of the actual product.
TABLE OF CONTENTS A Introduction, Safety and Warnings . . . . . . . . . . . . . . . . 2 B Before You Begin Assembly . . . . . . . . . . . . . . . . . . . 6 C Parts Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 7 D Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 E How to Use Your Ride-on Toy . . . . . . . . . . . . . . . . . 12 F Detailed Maintenance and Repair . . . . . . . . . . . . . . . 14 G Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION, SAFETY AND WARNINGS A ABOUT THIS MANUAL: This Manual was written to help you and your child get the most performance, comfort, enjoyment and safety when riding your new electric ride-on toy. It is important for you to understand your new electric ride-on toy. By reading this manual before you let your child go out on his/her first ride, you will know how to get the most from your new electric ride-on toy.
RIDER USE AND REQUIRED PARENTAL SUPERVISION RIDERS MUST NOT EXCEED THE WEIGHT LIMIT OF 65 lb (29.5 kg) and MUST BE OVER 3 YEARS OLD. NEVER ALLOW MORE THAN 1 CHILD TO RIDE THE RIDE-ON TOY SIMULTANEOUSLY. The age grade for the electric ride-on toy is for 3 years and older.
SAFE RIDING PRACTICES AND WARNINGS • Check and obey all local laws or regulations which may be in effect in the locations where the electric ride-on toy may be used. • Always wear appropriate clothing and shoes. • Observe the age and weight limitations on the cover of this manual. • Always stay seated while riding the electric ride-on toy. To stop you must take your foot off the foot pedal. • Children must be supervised by an adult at all times to be safe.
• Do not to allow hands, feet, hair, body parts, clothing, or similar articles to come in contact with wheels or other moving parts.
BEFORE YOU BEGIN ASSEMBLY B NOTE: Remove all packing and items from the display box. Make sure that the power switch is turned “OFF” before assembling the electric ride-on toy. ESTIMATED ASSEMBLY TIME You should allow approximately 5 minutes for assembly, not including initial charging time. Initial charging can take approximately 18 hours (see pages 10-11 for charging information). WARNING: DO NOT USE NON-ORIGINAL OR NON-RECOMMENDED PRODUCTS WITH YOUR ELECTRIC RIDE-ON TOY.
PARTS DIAGRAM C Tools Required Scissors (not included) 7 1 2 3 4 5 8 6 NOTE: Some parts shown are assembled on both sides of ride-on toy. 1. Head Assembly x1 2. Bandanna x1 3. M5 Locknut x1 4. M5x35 Machine Screw x1 5. Body Assembly x1 6. Battery (6V/4AH) x1 7. Stable x1 8.
ASSEMBLY D Your new ride-on toy has already been assembled at the factory, but there are a couple of things you need to do before you get started. TOOLS REQUIRED: Scissors (not included) WARNING: Children can be harmed by small parts, sharp edges and sharp points in the ride-on toy’s unassembled state, or by electrical items. In the unassembled state, this package contains small parts. Adult assembly is required; children should not handle parts, or help in assembly of the ride-on toy. 1.
• Gently turn the ride-on body on its side, and unzip the zipper which is located on the underside of the body. • Plug the power connector into the battery connector as shown in figure 4 below, and zip up the zipper.
BATTERY CHARGING IMPORTANT! Before first time use, charge the battery for at least 18 hours. Charge the battery for at least 12 hours after each use of the ride-on toy. Never charge the battery longer than 30 hours. Overcharging or undercharging the battery may shorten battery life and decrease ride-on toy running time. WARNING: The battery can fall out and injure a child if the ride-on toy tips over. Always use the battery retainer. PREVENT FIRE • Never modify the electrical system.
• Use only an original charger (AC 120V 60Hz) with an output of DC 6V 0.5A to charge your ride-on toy battery. • NOTE TO ADULTS: Regularly examine the charger for damage to the cord, plug, housing or other parts that may result in the risk of fire, electric shock or injury. • If your battery is old and will not accept a charge, do not leave it in the ride-on toy. Always remove a dead battery from the ride-on toy. • After the first charge, recharge the battery for at least 12 hours after each use.
HOW TO USE YOUR RIDE-ON TOY E Sound Button Foot Pedal Power Switch POWER SWITCH Turn the ride-on toy on and off. FOOT PEDAL To move the ride-on toy, press the foot pedal down. To stop, take your foot off the foot pedal. SOUND BUTTON Press the sound buttons on the handlebar to play sounds.
IMPORTANT • Do not let any child touch the wheels or be near them when the ride-on toy is moving. • To avoid accidents, inspect the ride-on toy before riding to ensure that it is in proper working order and safe to ride. • This toy has no brake; to stop, remove foot from foot pedal. • Check all the screws, cap nuts and protective coverings regularly and tighten as required. Check plastic parts on a regular basis for cracks or broken pieces.
DETAILED MAINTENANCE AND REPAIR Turn the power “OFF” before conducting any maintenance. TOOLS REQUIRED: Adjustable wrench (not included) Phillips Screwdriver (not included) HOW TO REPLACE FRONT WHEELS Front Wheel M8 Locknut M8x45 Bolt 1. Gently turn the ride-on body upside down. 2. Remove the M8 locknut and the M8x45 bolt with an adjustable wrench. 3. Remove the old wheel, and replace it with a new one. 4. Remount and tighten the M8 locknut and M8x45 bolt to secure the new wheel.
HOW TO REPLACE THE REAR WHEEL M6x25 Bolt Rear Wheel M10 Locknut M6 Locknut Rear Wheel 1. Gently turn the ride-on body upside down. 2. Remove the M6 locknuts and the M6x25 bolts with a phillips screwdriver. 3. Remove the M10 locknut with an adjustable wrench. 4. Remove the old wheel, and replace it with a new one. 5. Remount and tighten the M10 locknut, M6 locknuts and M6x25 bolts to secure the new wheel.
HOW TO REPLACE THE POWER SWITCH 1 2 Power Switch Socket Power Switch Power Switch 1. Gently turn the ride-on body on its side. 2. Use a screwdriver to remove the four screws from the left foot rest. 3. Carefully unplug the old power switch and plug in the new power switch for replacement. 4. Replace the foot rest and re-tighten the screws to finish. HOW TO REPLACE THE COAT Zipper Zipper Zipper 1. Gently turn the ride-on body upside down. 2.
HOW TO REPLACE THE FOOT PEDAL 1. Turn off the power switch in the car on the side of left foot rest. (see figure 1). 2. Use a flat head screwdriver to gently pry up the left side of the foot pedal (see figure 2). 3. Remove the old foot pedal and disconnect it from the pedal switch socket (see figure 3). 4. Connect the new foot pedal to the pedal switch socket and ensure they are connected in the correct position (see figure 4). 5.
BATTERY CARE AND DISPOSAL Do not store the battery in temperatures above 75° F (23.5° C) or below 32° F (0°C). THIS PRODUCT CONTAINS SEALED LEAD ACID BATTERIES WHICH MUST BE RECYCLED IN ACCORDANCE TO YOUR LOCAL AND STATE LAWS. PLEASE CAREFULLY READ AND UNDERSTAND THE FOLLOWING DISPOSAL INSTRUCTIONS: DISPOSAL: This product contains sealed lead acid batteries which must be disposed of or recycled in an environmentally safe manner. Do not dispose of the batteries in your household trash.
MAINTAINING YOUR RIDE-ON TOY Occasionally use a lightweight oil to lubricate moving parts such as wheels and the steering linkages. Park the ride-on toy indoors or cover it with a tarp to protect it from wet weather. Keep the ride-on toy away from sources of heat, such as stoves and heaters. Plastic parts may melt. ADULTS ONLY: Recharge the battery after each use. Recharge the battery at least once a month when the ride-on toy is not being used. DO NOT wash the ride-on toy with a hose.
TROUBLESHOOTING GUIDE Problem Possible Cause Solution Ride-on toy does not run Undercharged battery Charge the battery. A new battery should have been charged for at least 18 hours before using the ride-on toy for the first time. After first-time use, recharge the battery for at least 12 hours after each use. Never charge the battery longer than 30 hours. Check all connectors.
Problem Possible Cause Solution Ride-on toy was running but suddenly stopped Loose wires or connectors Check all wires and connectors. Make sure the battery connector is tightly plugged into the power connector, and that there are no loose wires around the motor. Tripped fuse The fuse may “trip” and shut down operation of the ride-on toy if the ride-on toy is overloaded or the driving conditions too severe.
Problem Possible Cause Solution Ride-on toy runs sluggishly Undercharged battery Charge the battery. A new battery should have been charged for at least 18 hours before using the ride-on toy for the first time. After first-time use, recharge the battery for at least 12 hours after each use. Never charge the battery longer than 30 hours. Check all connectors. Make sure the battery connector is tightly plugged into the charger connector, and that the charger is plugged into the wall outlet.
Problem Possible Cause Solution Charger gets warm during use It is normal for some chargers to get warm during use and is not reason for concern No action required. If your charger does not get warm during use, it does not mean that it is not working properly. Some chargers do not get warm during use Battery makes a sizzling or gurgling noise when charging It is normal for some batteries to make noise and swell slightly while charging and is not reason for concern No action required.
LIMITED WARRANTY Subject to the following limitations, all electric ride-on toys manufactured for Dynacraft are warranted to the original purchaser to be free of defects in materials and workmanship for a period of one year from the date of purchase, except with respect to batteries, for which the limited warranty period is six months from the date of purchase. No other express or implied warranty is given.
Dynacraft Customer Service 1-800-551-0032 8AM to 5PM Eastern Standard Time DO NOT return this item to the store. STOP Please call Dynacraft for assistance. Please have the following information available when you call: Model Number: (sample: 8802-33) Production Date: (sample: 03.03.2015) Serial Number: (sample: DA0233HD00001) Having this information will be required and helps us handle your call more effectively. Dynacraft BSC, Inc.
