User’s Manual SWTC1000 Model ______________ WARNING Read all precautions and instructions in this manual before using this equipment. Save this manual for future reference. Maximum user weight 175 lbs IMPORTANT Trampoline and Enclosures are susceptible to winds. Be sure to secure your trampoline and enclosure.
Model SWTC1000 ...........................................3 .....................................4 ..................................................4 .............................5 ...............................6 ...........................7 ..... ........................................8 ..............................9 ..........10-11 Part Identification Chart 12 Exploded Drawing and Parts List.........................13-14 Ordering Replacement Parts.................................14 Assembly.........
11. 12. 175 13. 14. 15.
14 round 4
METHODS OF ACCIDENT PREVENTION 4 7
• • 175 • • • 8
R 0 .
Model No. SWTC1000 Use below drawings to identify all the parts.
7 6 5 8 20 19 15 12 11 10 12 16 10 15 9 11 1 16 13 14 14 16 1 18 9 17 18 12 3 14 2 13 15 17 11 17 11 18 4 11 10 14 17 18 13 2 3 16 17 18 18 4 14 14 17 18 14 3 9 18 14 3 17 11 2 11 10 15 12 11 9 18 1 17 18 14 1 13 2 14 18 17 3 14 18 17 18 17 14 4 13 18 3 17 14 18 17 3 17 14
SWTC1000 Key No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 # # Qty.
r. • r. 14 • 1. Locate the Top tube with T-joint(1) and the Top tube with Socket(2) as shown. NOTE: Make sure all the spring holes are facing ground. 1 2 Socket T-joint 1 NOTE: If you don’t assemble in the right order, you will have to disassemble the entire trampoline in order to attach correctly. Identify the T-joint and Socket shown in right will be helpful for you, they are pre-installed on Top tube.
2. Insert the Leg Brace(4) into two Leg Extensions(3) as shown, then tighten with M6x47mm Bolts(14), M6 Washers(17) and M6 Nuts(18). 2 4 Press down on both Leg Extensions(3) at the same time and fully insert them into the T-joint and Socket , then tighten by M6x47mm Bolts(14) and M6 Nuts(18). 18 17 3 18 17 Repeat above assembly steps until four frame pieces are completed. then flip the trampoline frame pieces over so that the legs are now holding the trampoline frame pieces up.
4. If the Enclosure net(7) and Jumping mat(5) are not pre-installed, follow below steps to install. 4 7 4.1 Place the Jumping mat(5) on clear ground. Identify the warning label on mat top and the ID label on mat back as shown. 5 4.2 Place the Enclosure net(7) on the Jumping mat(5), make sure the first hole and the first V-ring are aligned as shown. 4.
5. If the Enclosure net and Jumping mat are pre-installed, follow below steps to assemble the Jumping mat to frame. 5 T-joint 5.1 Inspect the connection of Jumping mat and Enclosure net, make sure all the V-rings are passed through the corresponding net holes. Warning Decal 5 5.2 Place the Jumping mat(5) on clear ground inside the frame. and then adjust the location of two warning dacals to align the two T-joint in opposite direction as shown. Enclosure Door Warning Decal T-joint 5.
Attach the Spring as follows: 5 A: Hook one end of Spring (8) into the V-ring sewn on Jumping mat (5). B: Hook a Spring Tool as shown to the free end of the Spring. C: Pull the Spring (8) until it reaches the frame. D: Push the end of the Spring (8) into a hole in the frame, then unlook the Spring Tool V-ring 8 Frame CAUTION: It is wise to wear leather gloves while attaching the springs. Be careful where you place your hands as the Springs and Frame joints can pinch. 5.
5.6 Attach all the remaining V-rings with spring to Top tube holes correspondlingly. Enclosure door T-joint 6. Lay the Frame Pad(6) on the frame. Adjust it’s position so that the slits are just above the Sockets as shown. 6 6 CAUTION: Do not use the trampoline without the Frame Pad(6).The Frame Pad is designed to reduce the possibility of injuries due to jumpers coming in contact with the trampoline frame. If you do not have a Frame Pad,contact your dealer to obtain one.
7. Look underneath the trampoline. Locate the straps attached to the underside of the Frame PAD. Position each outer strap so that one strap is on each side of the frame as shown. Tie the outside straps sewn to the PAD Joints to each side of the frame as shown and attach the inner straps to the near V-rings. Inner Straps 7 Strap sewn in the outside of the Joint for the pad bottom Inner Straps 6 V-ring Frame Repeat this step to tie the remaining straps (not shown). Outer Strap Outer Strap 8 8.
10. Follow below steps to attach Curved tube to cap A A. Identify the hexagon hole on the Pole Cap(12) with a nut buried inside. B Hexagon hole 7 Holes 12 12 B. Insert the Pole Cap(12) into one strap ring on the top edge of net. Make sure the Hexagon hole side of the cap is against the net, and the holes on both the strap ring and the caps are aligned. Strap ring C 15 Strap Hole C. Hold the pole cap close to a Curved Tube(10), then Insert the Curved Tube(10) into the Pole Cap(12).
12. Insert the end cap(13) into the bottom hole of the Socket as shown. 12 Socket 13 13. Using a ladder, reach to the top of the enclosure poles and tie the straps around the pole caps as shown. Make sure to secure the knot tightly. (Do not stand on the edge of the trampoline to do this step. It can be dangerous and could damage the trampoline). 14. Using the included plastic tie, attach the Safety Placard to the frame near the point whare jumpers will climb onto and off the trampoline.
175 5 3 24
