Instruction Manual
Charging Battery
Step 1 - Pre-Flight Checklist
1. Read all warnings and instructions.
2. Install remote batteries, page 4.
3. Charge batteries, page 4.
4. Make sure that the drone and remote are powered o.
Step 2 - Choosing a location
• Drone is designed to be flown indoors and outdoors.
• Always make sure you have enough space to fly drone.
• Always follow warnings, page 2.
Step 3 - Pre-Flight
• Make sure your remote is o.
• Push the power button on top of the drone and hold on 1-2s until LED lights on.
• Place drone on a flat even surface. For ease of control, the blue lights should be toward you.
• Turn on the Remote controller.Push the left stick up and then down.
• The drone’s lights will flicker during the pairing process and then remain on once it has paired.
Step 4 - Lift O
Congratulations on your purchase of the LUMO Stunt Drone.
It’s time for some fun. This drone is capable of total controlled flight, fly up/down, left/right, and pitch forward or
backward, on 6 axis gyro stabilization. Includes USB charging cable, replacement blades and for auto orientation, auto
take-o and auto landing control. The remote controller requires requires 4 AAA 1.5V batteries (not included). Alkaline
batteries are recommended.
Please read all instructions and warnings in this manual prior to using your LUMO Stunt Drone, and keep this
instruction manual as it contains important information for future reference. Adult assembly and a Phillips
screwdriver will be required for battery installation.
Table of Contents
General Warnings Page 2
Contents Page 3
Remote Battery installation and Charging Battery Page 4
Replacing Propellers Page 5
Remote Overview Page 6
Operating Drone Page 7
Operating Page 8
Other Features Page 9
2 3
4 5
6 7
Sharper Image® name and logo (including the 77 logo) are trademarks or registered trademarks. Distributed by and
© 2022 MerchSource, LLC. Irvine, CA 92618. All rights reserved.
For customer support, please visit www.merchsource.com or call 1-800-374-2744.
The artwork and design of this manual are protected by US copyright law and may not be reproduced, distributed,
displayed, published or used for any purpose without prior written permission. It is not permitted to alter, remove or
reproduce any trademarks or copyright notice from this manual.
Printed in China
INSTRUCTION MANUAL
BATTERY WARNING:
• Do not mix old and new batteries.
• Do not mix alkaline, standard (carbon-zinc), or rechargeable batteries.
• Insert batteries using the correct polarity. Do not short-circuit the supply terminal.
• Remove batteries when not in use. Recycle or dispose of exhausted batteries according
to federal, state, and local laws. Do not dispose of batteries in a fire - they may leak or
explode.
• Only use manufacture specified battery(ies), charger(s) and/or adapter, if applicable,
specified by the manufacturer.
• Always use, replace, and recharge (if applicable) batteries under adult supervision.
KEEP THIS PACKAGING FOR REFERENCE AS IT CONTAINS IMPORTANT INFORMATION.
1. Unscrew the screw at the bottom of
the controller and then slide open
the battery compartment.
2. Install 4 “AA” 1.5V batteries.
3. Replace and secure battery
compartment with screw.
LED Drone
BATTERY WARNING-LITHIUM-POLYMER:
There is a risk of fire and personal injury if Li-Po battery is punctured, damage or misused.
• Never expose battery to extreme temperatures or moisture.
• Do not subject battery to strong impacts.
• Always keep battery away from flammable materials.
• Only use manufacture specified battery(ies), charger(s) and/or adapter, if applicable,
specified by the manufacturer.
• Battery is not serviceable.
• Let battery cool to room temperature before charging.
• While charging, never leave battery unattended.
• Recycle or dispose of battery according to federal, state and local laws.
KEEP THIS PACKAGING FOR REFERENCE AS IT CONTAINS IMPORTANT INFORMATION.
USB Charger Cable4 Replacement Propellers.
Note: The drone will light up when it is charging and turn o when the battery is fully charged.
1. Turn o the drone before charging.
2. Connect the battery charger cable to the charging port on the drone.
3. Connect USB connector to the power source.
• Only an adult should replace blades. To remove, pull up the blades directly.
• Replace propellers by following the diagram.
• Each blade spins dierently. Blade B spins counter clockwise and Blade A spins clockwise.
1
Drone Controller
3. Use the Multi Directional
Joystick to move
forwards, backwards or
side to side.
Step 7 - Retrieving Drone
1. Turn o your remote. This will stop you from
accidentally turning the propellers on.
2. Make sure the propellers have stopped spinning
then pick up your drone. Press and hold the
drone's on/o button to turn the drone o.
Note: You will need to pair your drone again
before your next flight, (part 1 of step 4).
Tips
• Do not crash drone into sand or dirt. Drone gears may become clogged.
• When first learning to fly, practice lifting o and hovering indoors.
• Stay several feet from walls and objects.
1. Prepare for flight
• Drone must be charged before each use (Cable included).
• Indicator light on Drone will turn o when fully charged.
• Install batteries in remote.
2. Pair your drone
Before each flight pair the remote with the drone:
• Turn your drone on and place on a flat, level surface.
• Turn on the remote.
• Push the left stick up and then down.
• Repeat steps 1 and 2 if necessary.
3. Calibrate
• Move both joysticks diagonally in toward the middle of the remote.
4. Remote Control Overview
Practice flying your drone indoors, below 10 feet, and at low speeds until comfortable with all controls to avoid
unnecessary damage or injury.
• Left joystick: Up/Down controls elevation.
• Right joystick: controls flight direction.
• Direction Trim: Use to eliminate drift .
• Press the "Take O Land" button to take o and land.
To cut power to drone, press and hold red STOP button.
8 9
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
4. Stunts - Press the
Stunt Button then
press the Multi
Directional Joystick in
the direction you want
to complete a stunt.
Pres the Auto Stunt
Button to complete a
radomn stunt.
Note:
1. The stunt function may be
disabled if the drone battery
power is low.
2. Hover the drone at or above 10
feet before attempting a stunt.
5 FEET
10 FEET
Press the Take o Land Button. Slowly and carefully press
the Throttle stick up. Drone
will begin to elevate.
14+
OR
SPEED
STOP
TRIM
TRIM
LIGHT MODEL
AUTO ARIENTATION
TAKE OFF
LAND
STUNT
AUTO STUNT
SPEED
STOP
TRIM
LIGHT MODEL
AUTO ARIENTATION
TAKE OFF
LAND
LUMO STUNT DRONE
BC
SPEED
STOP TRIM
TRIM
LIGHT MODEL
AUTO ARIENTATION
TAKE OFF
LAND
STUNT
AUTO STUNT
LUMO STUNT DRONE
INTRODUCTION
INTRODUCTION
GENERAL WARNINGS CONTENTS
REMOTE BATTERY INSTALLATION REPLACING PROPELLERS
REMOTE OVERVIEW OPERATING DRONE
OPERATING OTHER FEATURES
KEEP THIS INSTRUCTION MANUAL AS IT CONTAINS IMPORTANT INFORMATION
FOR FUTURE REFERENCE.
Due to continuous product improvements, the picture on the manual may dier
slightly from the actual product.
Adult Assembly Required
WARNING:
CHOKING HAZARD -
Small Parts.
Not for children under 3 years.
SPEED
STOP TRIM
TRIM
LIGHT MODEL
AUTO ARIENTATION
TAKE OFF
LAND
STUNT
AUTO STUNT
A
A
B
B
SPEED
STOP
TRIM
TRIM
LIGHT MODEL
AUTO ARIENTATION
TAKE OFF
LAND
STUNT
AUTO STUNT
SPEED
STOP TRIM
TRIM
LIGHT MODEL
AUTO ARIENTATION
TAKE OFF
LAND
STUNT
AUTO STUNT
Step 5 - Operating Drone in Flight
1. Follow this step if your
drone begins to drift during
take o or during flight.
A. Drone drifts backwards:
Press the Forward Trim
Button.
B. Drone drifts forwards:
Press the Backwards Trim
Button.
C. Drone drift right: Press the
Left Trim Button.
D. Drone drift left: Press the
Right Trim Button.
2. Use the Throttle
Joystick to increase or
decrease your elevation.
Step 6 - Landing Drone
1. Lower drone to 20 feet or less then press the Take
O Land button. Use the Multi Directional Joystick
to maneuver drone. Or Push the left joystick down
until the drone landing.
2. In the event the blades will not stop spinning, you
can perform an emergency stop by pressing and
holding the red STOP button.
STOP
TRIM
TRIM
LIGHT MODEL
AUTO ARIENTATION
STUNT
AUTO STUNT
SPEED
STOP TRIM
TRIM
LIGHT MODEL
AUTO ARIENTATION
TAKE OFF
LAND
STUNT
SPEED
STOP
TRIM
TRIM
LIGHT MODEL
AUTO ARIENTATION
TAKE OFF
LAND
STUNT
AUTO STUNT
Auto Orientation
Press the Auto Orientation Button to turn the mode ON and then again to turn o.
• In this mode, the drone will always move in the direction you press the Multi Directional Button no matter which
way the drone faces. When drone is in auto orientation mode, the drone will orient to the user (remote), no matter
what direction the drone is facing.
• Press the Orientation button. Remote will beep every 6 seconds to indicate it is in Auto Orientation mode.
• Push the right stick up will send the drone away from the user, push left will move left, etc.
• Press Auto Orientation button to exit mode.
Adjust Speed
• Press the Speed button to toggle through three dierent speeds. Each speed is indicated by a tone.
Changing Drone Lights
• Press the Light Mode button to toggle between light on, slow pulse, fast pulse, and lights o.
Charge with Remote
• Use the controller to charge your drone when no other power source is available. Plug in the provided USB cable
into the back of the controller to charge the drone.
SAFETY WARNINGS
• Not recommended for children under 14 years of age. As with all electrical products, precautions should be observed during
handling and use to reduce the risk of electrical shock.
• Adult supervision is required at all times.
• Never fly drones above or near people, sudden changes in wind or other conditions could lead to unexpected crashes.
• Always use caution when flying drone vehicles, obey relevant laws, respect the privacy and property rights of others.
• The drone shall never be modified or used for anything except its intended purpose.
• Before each use, an adult should review the product and battery to determine that no damage or hazards exist.
• DO NOT TOUCH SPINNING PROPELLERS.
• Do not allow anything to intentionally make contact in any way with spinning propellers or prevent contact with spinning blades
by turning o remote prior to handling drone.
• Use caution and pay attention to your surroundings while operating drone.
• Do not fly drone into animals, people, or inanimate objects.
• Keep drone away from power lines, buildings, trees, public areas, and any other potentially hazardous areas.
• Do not operate in rain, heavy wind, and or any type of severe weather.
• Do not land drone on wet surfaces.
• Never touch or allow others to touch drone while it is flying.
• Always turn drone o when it is not in use.
• Always fly drone in large open areas.
Fly-aways are the responsibility of the individual pilot and will not be replaced by the manufacturer.
Connect the battery
charger to drone
Connect the battery
charger to drone
WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accord- ance with the instructions, may cause harmful interference to radio communications. However
there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment o and on the user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Insert the USB
connector into a USB
power source
Insert the USB
connector into a USB
power source