セイコーシステム ストップウオッチ S149 取扱説明書 INSTRUCTION
−−−−−−−−−−−−−−−−−−−− CONTENTS −−−−−−−−−−−−−−−−−−−−−−− １.FEATURES ……………………………38 ２.DISPLAY AND BUTTON/SWITCH OPERATION ……………………………39 ３.TIME/CALENDAR ……………………40 ４.HOW TO USE THE STOPWATCH …………………………40 ５.HOW TO USE THE MEMORY FUNCTION………………………………48 ６.HOW TO PRINT OUT ………………53 ７.HOW TO USE THE AUTO START FUNCTION …………………59 ８.HOW TO INSERT BATTERIES INTO THE PRINTER …………………………64 ９.TIME・CALENDAR SETTING ………………………………65 10.PRECAUTIONS ………………………68 11.REMARKS ON THE BATTERIES……………………………71 12.
３.TIME/CALENDAR ４.HOW TO USE THE STOPWATCH １ Press mode selection button ③ (TIME) to set □ Notes on the block of data in memory ・The SEIKO Stopwatch Cal. S149 features a "Block Memory" stopwatch operation system. The data obtained from start till finish of a race is recorded as a block and stored in memory. ・The time and date of starting the measurement of a block of data are automatically stored in memory.
Accumulated elapsed time measurement (Start) Ａ→○ Ａ→○ Ａ…→○ Ａ→○ Ｂ Press the buttons in the following order: ○ (Restart) (Stop) SPLIT SPLIT SPLIT F F BLOCK LAP F BLOCK LAP STOP BATT. LAP BLOCK LAP STOP BATT. LAP E STOP BATT. LAP E RECALL LAP／SPLIT RESET START STOP \ START STOP \ LAP／SPLIT RESET E RECALL Ａ ○ Ａ ○ LAP／SPLIT RESET START STOP \ RECALL Ａ ○ (Stop) (Reset to "00") Restart and stop of the stopwatch Ａ.
When the grip switch is used: ① Changeover to the grip switch ② Time measurement ● Connect the grip switch to the stopwatch. ● The measurement is started by pressing the grip switch once. Split time and lap time can be measured repeatedly with each press of the grip switch. （Start）→（With each press of the grip switch, split time and lap time are measured repeatedly.） Grip switch ● Slide up the grip switch selector located on the right side of the stopwatch.
When the stopwatch is reset or stopped: The data is recalled starting from the first data in block "1". (Reset) (Start data) SPLIT （Fastest lap time display） (Lap/split data in block "1") SPLIT SPLIT F F BLOCK LAP STOP BATT. LAP E Recall button RECALL F BLOCK LAP STOP BATT. LAP E Recall button RECALL STOP BATT. LAP E Recall button BLOCK LAP STOP BATT. LAP E Recall button STOP BATT. LAP RECALL Fastest lap no.
■Notes on memory capacity ・The number of data in memory is shown graphically by the memory capacity indicator. ・Besides the measured lap times/split times, the start time data and block number are also retained in memory as two separate data. Therefore, a block of data includes at least three data. If more than one block is used to store the data, the memory become full even before the number of lap time/split time measurements in memory amounts to 300.
Printout after the measurement "Printout of the desired block of data" POWER ON （１）Turn on the power switch. （２）Press memory recall button (RECALL). The time data stored in memory are printed out. SPLIT F BLOCK LAP STOP BATT. LAP E RECALL STOP-W. A/S SET TIME ＊When all the stored data are printed out, the printer automatically stops. LOCK CLEAR 1/100 START STOP STOP.W A/S SET TIME ②Turn on the power switch of the printer. ③Keep recall button pressed.
２ Press button Ａ □ ○ to start the printout. With each press of button Ｂ ○, the time when the lap time is measured is printed out.
２.Transfer of the designated auto start time to other stopwatch (Cal. S143, S123, S124) POWER ON SYSTEM STOPWATCH (EX.) Marathon race By transferring the designated auto start time to stopwatches Cal. S143, they can start the measurement at the same time. RECALL LAP/SPLIT RESET SELECT CLEAR START STOP SYSTEM STOPWATCH SET SPLIT F BLOCK LAP STOP BATT. LAP E Starting point First checkpoint Second checkpoint Finish RECALL STOP-W.
８.HOW TO INSERT BATTERIES INTO THE PRINTER Use four SUM-3 (R6P) dry batteries. □ １ Slide the power switch to "OFF" and then remove the battery hatch. □ ２ Inset the batteries into the battery compartment as shown in the illustration below, checking that the (+) and (-) terminals are properly set. ３ Close the battery hatch. □ Put the hatch toward you while pushing the portion indicated by the arrow. battery hatch Slide the battery hatch along the grooves of the battery compartment. ９.
３.Adjustment of the contrast on the display ・The contrast of the display can be adjusted. ②Press recall button to show the contrast adjustment display. The contrast can be adjusted for 10 levels from level "1" to "10". The display is the lightest at level "1" and the darkest at level "10". ①Show the time/calendar mode. ID BLOCK LAP STOP BATT. LAP RECALL SPLIT BLOCK LAP Contrast adjustment display A : Increasing the level (darker) Button ○ Button ○ B : Decreasing the level (lighter) STOP BATT.
CAUTION ・Your watch is not water-resistant, be careful not to get it wet with water. CAUTION ・If your watch is of the fob or pendant type, the strap or chain attached to the watch may damage your clothes, or injure the hand, neck, or other parts of your body. PLACES TO KEEP YOUR WATCH × × ・If the watch is left in a temperature below -10℃ or above +60℃ for a long time it may function improperly or stop operating.
.TROUBLESHOOTING GUIDE Before requesting service, please check your stopwatch following the table below. Problem The motor does not run even if the power switch of the printer is turned "ON". The paper is not advanced by pressing the paper advancing switch. By pressing the start button, the paper is advanced, but the printed digits or letters are detective or the data are not printed at all.
