NOTE: TO OPERATE, PUSH START SCOOTER TO APPROXIMATELY 3 MPH WHILE TWISTING THROTTLE IN ORDER FOR MOTOR TO ENGAGE. THE SCOOTER MUST BE ROLLING AT 3 MPH BEFORE THE MOTOR WILL ENGAGE. ELECTRIC SCOOTER OWNER’S MANUAL FOR USE WITH THE FOLLOWING PULSE PERFORMANCE PRODUCTS™ SCOOTERS • REVSTER DO NOT RETURN TO STORE! QUESTIONS OR COMMENTS? CALL (866)-434-6067 05.06.
Table of Contents Safety and Warnings Before You Start Assembly Hardware Maintenance Before You Ride Repair and Maintenance Troubleshooting Scooter Components Warranty 2-3 4 5-6 7 7 8-11 12 13 14 Safety and Warnings WARNING: Riding an electric scooter can be a dangerous activity. Certain conditions may cause components to fail without fault of the manufacturer.
Safety and Warnings Maintain a hold with both hands on the handlebars at all times. Never allow more than one person at a time to ride the scooter. Never use near steps, water, or swimming pools. Keep your fingers and other body parts away from the chain, motor, steering system, wheels and all other moving components. Never ride while using a cell phone or wearing headphones. Never hitch on to or with another vehicle or pull anyone or anything.
Before You Start WARNING: Remove all packing and items from the display box. Make sure that the power switch is turned “OFF” before assembling the scooter. Estimated Assembly Time • Allow up to 25 minutes for assembly, not including initial charge time. • Allow up to 12 hours for the initial charge (see page 6 for charging information).
Assembly Handlebar Steer Tube Assembly Tools required: 5 mm hex wrench, 10 mm wrench c a b 1. Depress the push button located on the rear of the fork and insert the handlebar steer tube onto the fork. The push button should align with the locator hole in the handlebar steer tube and lock the steer tube securely in place. 2. Tighten the bolts with the 5 mm hex wrench and 10 mm wrench. Tighten bolts evenly and securely. d 3.
Assembly Charging the Battery WARNING: Battery must be fully charged before you ride your electric scooter. Required components: battery charger • Initial battery charge time - 12 hours • Recharges after initial charge - up to 10 hours • When scooter is not in regular use batteries need to be charged on a monthly basis to maximize performance 1. Make sure power switch is in the OFF position before plugging in the charger. Insert charger into charging port on the right side of the battery box. 2.
Hardware Maintenance Brake Check the brakes for proper function. When you step on the brake it should provide positive braking action. When you apply the brake with the speed control on, the brake cut off switch should stop the motor. Frame, Fork and Handlebars Check for cracks or broken connections. Although broken frames are rare, it is possible for aggressive rider to run into a curb or wall and bend or break a frame. Get in the habit of inspecting your scooter on a regular basis.
Repair and Maintenance Chain and Rear Wheel Replacement Tools required: 4 mm hex wrench, 5 mm hex wrench, two [2] 13 mm wrenches, 10 mm wrench, phillips screwdriver 1. Using a 4 mm hex wrench remove the 2 bolts from the rear chain cover on side of the scooter. 2. Using two [2] 13 mm wrenches loosen the rear wheel axle nuts. CAREFULLY remove the wheel AND axle from the frame, with the wheel remaining on the axle. 3. Note the location of all rear wheel hardware and ensure to properly reinstall all items.
Repair and Maintenance Chain and Rear Wheel Replacement (Continued) 4. If replacing the chain, remove the motor bolts with a 4 mm hex wrench. Slide motor out of the frame slightly so that there is enough room to remove/replace the chain onto the motor gear. Replace spacers and retighten bolts. 5. Place the chain under the guiding wheel and onto the rear chain wheel gear, and install replacement wheel into the frame. Do not tighten axle nuts yet. 6.
Repair and Maintenance Front Wheel Replacement Tools required: Two 5mm hex wrenches 1. Using two 5 mm hex wrenches loosen and remove the front axle by turning the wrenches counter clockwise. 2. Reinstall new replacement wheel ensuring to note the order and location of all components. 3. Reinstall hardware and tighten clockwise with a 5 mm hex wrench. Battery Care and Disposal Do not store the battery in temperatures above 70°F (21°C) or below 32°F (0°C).
Repair and Maintenance Battery Charger Only use the supplied battery charger. If battery charger is damaged discontinue use immediately and replace with a Pulse Performance Products™ recommended battery charger. Wheels Wheels and drive system components are subject to normal wear and tear. It is the responsibility of the user to regularly inspect wheels for excess wear and adjust and replace drive train components as required.
Troubleshooting Problem Possible Cause Solution Scooter will not run. Battery is not charged. Fully charge the battery. First charge should be 12 hours and up to 10 hours for recharges. Wires or connectors are loose or unplugged. Check to ensure that charger is tightly plugged into both the wall and the scooter. Must be rolling 3mph (5 km/h) for motor to engage. Push start scooter to approximately 3 MPH (5 km/h) while twisting throttle in order for motor to engage.
Scooter Components part description 1 Frame 2 Motor 3 Front Fork 4 Headset 5 Clamp 6 Kickstand 7 Battery Box 8 Deck 9 Rear Wheel 10 Chain Cover 11 Front Wheel 12 Chain 13 Thumb Throttle 14 Grip 15 Controller 16 Battery 17 Steer Tube 18 Handlebar 19 Handlebar Clamp 20 Charger Port 21 Reset Button 22 On/Off Switch 23 Chain Wheel 24 Guide Wheel 25 Brake Cut-Off Switch Questions or concerns? Visit our website at www.pulsescooters.
Warranty Limited Warranty The manufacturer warranties this product to be free of manufacturing defects for a period of 90 days from the date of purchase. This Limited Warranty does not cover normal wear and tear, tires, cables, or any damage, failure or loss caused by improper assembly, maintenance, storage or use of this Pulse Performance Products™ electric scooter.
Questions or concerns? Visit our website at www.pulsescooters.com for replacement parts and technical support, or call (866) 434-6067.
facebook.com/pulseperfprod twitter.com/pulseperfprod Pulse Performance Products™ A Division of Bravo Sports™ 12801 Carmenita Rd.
