Power Washer Owner’s Manual 005612 MODEL:________________________ SERIAL:________________________ DATE PURCHASED:______________ Register your Powermate product at: www.powermate.
Table of Contents Section 1 Introduction and Safety 1 Introduction ..................................... 1 Safety Rules .................................... 1 Safety Symbols and Meanings ........ 2 Section 2 General Information and Setup .............................................. 3 Know Your Power Washer .............. 3 Emissions ........................................ 3 Remove Contents from Carton ....... 3 Assembly ......................................... 3 Add Engine Oil ..........................
Introduction and Safety Section 1 Introduction and Safety Introduction Safety Rules WARNING Consult Manual. Read and understand manual completely before using product. Failure to completely understand manual and product could result in death or serious injury. (000100a) Thank you for purchasing a Powermate product. This unit has been designed to provide high-performance, efficient operation, and years of use when maintained properly.
Introduction and Safety Safety Symbols and Meanings DANGER Asphyxiation. Running engines produce carbon monoxide, a colorless, odorless, poisonous gas. Carbon monoxide, if not avoided, will result in death or serious injury. (000103) DANGER Electrocution. Water contact with a power source, if not avoided, will result in death or serious injury. (000104) DANGER Explosion and Fire. Fuel and vapors are extremely flammable and explosive. Add fuel in a well ventilated area. Keep fire and spark away.
General Information and Setup Section 2 General Information and Setup Know Your Power Washer Assembly WARNING WARNING Consult Manual. Read and understand manual completely before using product. Failure to completely understand manual and product could result in death or serious injury. (000100a) Read this manual thoroughly before assembling and operating this unit. Save this manual for future and immediate reference. Replacement owner’s manuals are available at www.powermate.com.
General Information and Setup See Figure 2-3. Install vibration mount (B) and secure with lock nut and 13mm wrench. A 000115 B Figure 2-6. Remove Dipstick 006426 Figure 2-3. Install Gun Rest and Vibration Mount See Figure 2-4. Install wheels as follows: 1. Slide axle pin (D) through the wheel (C), washer (B) and wheel bracket on frame. 2. Insert cotter pin (A) through axle pin (D). D 4. Add recommended engine oil. NOTE: Some units have more than one oil fill location.
General Information and Setup 4. Slowly add recommended fuel. Do not overfill. . 005609 000117 Figure 2-8. Add Recommended Fuel 5. Install fuel cap. Figure 2-9. Inspect Inlet Screen 4. See Figure 2-10. Connect water supply hose to pump water inlet and handtighten. . NOTE: Allow spilled fuel to evaporate before starting unit. Water Supply NOTE: DO NOT run unit without sufficient water supply. Failure to follow water supply requirements will void unit warranty.
General Information and Setup Nozzles 1. Select correct nozzle for task. 2. See Figure 2-15. Pull back quick–connect collar and install nozzle. 3. Release quick-connect collar to secure nozzle. 4. Verify nozzle is locked in place. 005611 Figure 2-12. Connect High-Pressure Hose to Pump 4. See Figure 2-13. Connect high-pressure hose to base of spray gun and handtighten. 000125 Figure 2-15.
General Information and Setup Wash Pressure Nozzle (White) DELICATE - Lower pressure and higher flow for gentle cleaning of cars/trucks, boats, RV’s, patio furniture, lawn equipment, etc. 001399 Detergent Nozzle (Black) DETERGENT ONLY (BLACK), Only use power washer safe detergents/soaps to help break down stubborn dirt and grime on a variety of surfaces.
Operation Section 3 Operation Operation and Use Questions Call Powermate Customer Service at 1-800445-1805 with questions or concerns about unit operation and maintenance. Before Starting Engine Unit is shipped with no oil in the crankcase. Add engine oil before starting. See Engine Oil Recommendations. 1. Verify engine oil level is correct. 2. Verify fresh fuel level is correct. 3. Verify all fittings and couplers are properly secured. 4. Verify sufficient water supply is properly connected. 5.
Operation A CLOSED OPEN B 000129 005555 Figure 3-2. Fuel Valve and Choke NOTE: For warm engine, verify choke lever is in OPEN position. 4. See Figure 3-3. Turn engine switch ON. WARNING OFF Fluid Injection. This machine produces high-pressure fluid streams that can pierce skin. Fluid injection could result in death or serious injury. (000106b) ON 000128 Figure 3-3. Engine Switch WARNING Vision Loss. Eye goggles are required to be worn when using this machine.
Operation Apply Detergent WARNING Fluid Injection. This machine produces high-pressure fluid streams that can pierce skin. Fluid injection could result in death or serious injury. (000106b) WARNING Personal injury. Risk of fluid injection. Do not aim spray gun at people, animals, electrical devices, or fragile items. Keep out of reach of children. Failure to do so could cause death or serious injury. (000117c) NOTE: DO NOT use caustic liquid with power washer. Use ONLY power washer safe detergents.
Section 4 Maintenance and Troubleshooting Maintenance Regular maintenance will improve performance and extend engine/equipment life. The manufacturer recommends that all maintenance work be performed by an Independent Authorized Service Dealer (IASD). Regular maintenance, replacement or repair of the emissions control devices and systems may be performed by any repair shop or person of the owner’s choosing.
Inspect Spray Gun NOTE: Replace spray gun immediately if it fails any test steps. 000131 Figure 4-3.Back Flush Lance 000123 Figure 4-1.Test Spray Gun (typical) 1. Verify spray gun hose connection is secure. 2. Squeeze and release trigger. NOTE: Trigger should spring back into place and lock when released. Nozzle Maintenance A pulsing sensation felt when squeezing spray gun trigger may be caused by excessive pump pressure. Typical causes of excessive pump pressure are nozzle clog or restriction.
000115 A Figure 4-5. Engine Oil Fill 4. See Figure 4-6. Screw dipstick into filler neck.Verify proper oil level on dipstick. 001556 Figure 4-7.Oil Drain Plug Air Filter 000116 Figure 4-6. Safe Operating Range 5. Add recommended engine oil as necessary. 6. Replace oil fill cap and hand-tighten. NOTE: Some units have more than one oil fill location. It is only necessary to use one oil fill point.
Inspect Spark Arrestor Screen (if equipped) WARNING Hot Surfaces. When operating machine, do not touch hot surfaces. Keep machine away from combustibles during use. Hot surfaces could result in severe burns or fire. (000108) 000134a Figure 4-8. Spark Plug NOTE: Replace spark plug if electrodes are pitted, burned or porcelain is cracked. Use ONLY recommended replacement plug. See Product Specifications Sheet. 4.
Storage Change Oil General Change engine oil before storage. See Change Engine Oil DANGER Explosion and Fire. Fuel and vapors are extremely flammable and explosive. Add fuel in a well ventilated area. Keep fire and spark away. Failure to do so will result in death or serious injury. (000105) WARNING Risk of Fire. Verify machine has properly cooled before installing cover and storing machine. Hot surfaces could result in fire. (000109) • DO NOT place a storage cover on a hot power washer.
Troubleshooting Problem Cause Correction Pump fails to produce pressure, has erratic pressure, chattering, loss of pressure, low water volume. 1. Low pressure nozzle installed. 2. Water inlet is obstructed. 3. Inadequate water supply. 4. Inlet hose kinked or leaking. 5. Clogged hose inlet screen. 6. Water supply is over 100ºF (37.8ºC). 7. High-pressure hose is obstructed, or leaks. 8. Spray gun leaks. 9. Nozzle is obstructed. 10. Pump is faulty. 1. Replace with high-pressure nozzle. 2. Clean inlet. 3.
Part No. 10000015110 Rev. C 05/30/2018 ©2018 Powermate, LLC. All rights reserved. Specifications are subject to change without notice. No reproduction allowed in any form without prior written consent from Powermate, LLC. Powermate, LLC S45 W29290 Hwy. 59 Waukesha, WI 53189 1-800-445-1805 www.powermate.
