Internet Camera & Internet Video Server Quick Installation Guide
Table of Contents Chapter 1. Introduction..................................................................................... 4 1.1 Before Installation..................................................................... 4 1.2 System Requirements for Viewer................................................ 4 Chapter 2. IVS-110 – 1-Channel Internet Video Server........................................ 5 2.1 Package Content........................................................................ 5 2.
7.2 Identification of Cables..............................................................18 7.3 Physical Installation..................................................................20 Chapter 8. IPwizard Installation and operation...................................................21 8.1 IPwizard Installation..................................................................21 8.2 Wizard function........................................................................24 8.3 Username and Password ...........
Chapter 1. Introduction Thank you for purchasing the IP surveillance product. It is versatile and high image solution of the perfect indoor / outdoor surveillance application. The IP surveillance state-of-art design is considerable to fit in various network environments. 1.1 Before Installation Before installation, please be sure to read this quick installation guide and user’s manual (CD) carefully to complete machine installation. This QIG includes the following chapter: • Chapter2.
Chapter 2. IVS-110 – 1-Channel Internet Video Server 2.1 Package Content IVS-110 x 1 Power Adapter x 1 Power Cable x 1 CD Disk x 1 Quick Installation Guide x 1 Note 1. If any of the above items are missing, please contact your dealer immediately. 2. Using a power supply with a different voltage that the one included with the IVS-110 will cause damage and void the warranty for IVS-110. 2.2 Physical Installation 2.2.
Video-in Jack You can install an analog camera and connect it to video-in jack. 12V DC-Out Jack The output power is 12V DC. This is used to supply 12V DC power to one external camera. The output power is 12V DC, 400mA maximum. The output power still supplies 12 V DC, 400mA power to one external, when the IVS-110 obtains power from PoE switch. DI/DO/RS-485 Connector This IVS-110 provides a general I/O terminal block with one digital input and one output for device control.
12V DC-in Jack The input power is 12V DC. Note Only use the power adapter supplied with IVS-110. Otherwise, the product may be damaged. 2.2.3 Installation Steps 1. Attach video source to IVS-110 To use IVS-110, user must supply video source to IVS-110. Connect the BNC terminal of camera to the IVS-110’s video input and make sure to power on camera first. 2.
Chapter 3. ICA-310 – 30M Infrared Internet Camera 3.1 Package Content ICA-310 x 1 Power Adapter x 1 Wall Mount Accessories x 1 CD Disk x 1 Quick Installation Guide x 1 Note 1. if any of the above items are missing, please contact your dealer immediately. 2. Using a power supply with a different voltage that the one included with the ICA-310 will cause damage and void the warranty for ICA-310. 3.2 Physical Installation 1.
3. Identification of ICA-310 cables ● RS485 cables (Blue: D+ / Red: D-) - To connect to P/T scanner. ● Power Connector – Connect to DC 12V power adapter. ● BNC connector – For analog video output. ● RJ-45 Connector – For connect a CAT5 cable to hub or switch. The RS-485 of ICA-310 is master that can control external scanner.
Chapter 4. ICA-312 – 25M Infrared Internet Camera 4.1 Package Content ICA-312 x 1 Power Adapter x 1 Wall Mount Accessories x 1 CD Disk x 1 Quick Installation Guide x 1 Note 1. if any of the above items are missing, please contact your dealer immediately. 2. Using a power supply with a different voltage that the one included with the ICA-312 will cause damage and void the warranty for ICA-312. 4.2 Physical Installation 1.
Chapter 5. ICA-350 – 30M Infrared Internet Camera 5.1 Package Content ICA-350 x 1 Power Adapter x 2 (one for ICA-350, another for heater) Wall Mount Accessories x 1 CD Disk x 1 Quick Installation Guide x 1 Note 1. if any of the above items are missing, please contact your dealer immediately. 2. Using a power supply with a different voltage that the one included with the ICA-350 will cause damage and void the warranty for ICA-350. 5.2 Physical Installation 1.
3. Identification of ICA-350 cables ● BNC Connector – For analog video output ● Power Connector – Connect to DC 12V power adapter (for ICA-350) ● RS485 cables (Black: D- / Red: D+) - To connect to P/T scanner. ● RJ-45 Connector – For connect a CAT5 cable to hub or switch. ● Power Connector – Connect to DC 12V power adapter (for heater) The RS-485 of ICA-350 is master that can control external scanner.
Chapter 6. ICA-525 – 20M IR Vandal Proof Dome Internet Camera 6.1 Package Content ICA-525 x 1 Power Adapter x 1 Screws x 4 Telephone box x 1 L-Wrench x 1 CD Disk x 1 Quick Installation Guide x 1 Note 1. if any of the above items are missing, please contact your dealer immediately. 2. Using a power supply with a different voltage that the one included with the ICA-525 will cause damage and void the warranty for ICA-525. 6.
1. RJ-45 LAN socket: Connect to PC or Hub/Switch. For connect to 10Base-T Ethernet or 100Base-TX Fast Ethernet cabling. This Ethernet port built N-Way protocol can detect or negotiate the transmission speed of the network automatically. Please use Category 5 “straight through” cable to connect the ICA-525 to a 100Mbps Fast Ethernet network switch or hub. Note In case you need to connect the device to PC or notebook directly, you should use cross over cable instead. 2.
screws still attached on the cover). The unit has factory installed side conduit entry and one may adjust the cables to back conduit entry according to installation requirement. Note During the installation, please take care and avoid crash. That may cause people hurt and this device damage. 2. Set the mounting base onto the wall or ceiling and center it over the mounting hole, using the supplied four retaining screws to secure the main body.
3. Set the proper image by moving the camera body and set the focus by turning the lens to left or right direction. Note 1. Vari-Focal Dome Operation Guide: Once the picture appears on the monitor, open the cover and adjust the lens wrench to “NEAR ←→ FAR”, get the view zoom that you desire, and then adjust the focus wrench of the lens to obtain the best picture. After adjustment, tighten both wrenches. 2. You may power on the ICA-525 and connect it to a monitor template for adjust the image. 3.
5. When using the side conduit cabling, it is suggested to cover the cables using metal covers (to prevent external damage and for waterproof prevention), and wined the waterproof adhesive type onto the metal cover before installation. 6. Connect the LAN cable to Ethernet’s switch or hub and the DC-Jack to the power source. The video output to monitor or other video through a 75 Ohms type coaxial cable if you will use BNC cable. 7.
Chapter 7. ICA-530 – 15M IR Dome Internet Camera 7.1 Package Content ICA-530 x 1 Power Adapter x 1 Wrench x 1 Telephone box x 1 CD Disk x 1 Quick Installation Guide x 1 Note 1. if any of the above items are missing, please contact your dealer immediately. 2. Using a power supply with a different voltage that the one included with the ICA-530 will cause damage and void the warranty for ICA-530. 7.
5 “straight through” cable to connect the ICA-530 to a 100Mbps Fast Ethernet network switch or hub. In case you need to connect the device to PC or notebook directly, you should use cross over cable instead. Note 2.
7.3 Physical Installation 1. Drill 20mm (3/4”) holes in the ceiling or wall and then align the mounting plate to the holes you have made as below. Ceiling Top Plate Directly install on any horizontal or vertical surface 2. Camera Adjustment: Tilting View Rotating View Panning View Angle range is 0˚~90˚ Angle range is 0˚~180˚ Angle range is 0˚~180˚ 3. Connect the necessary cables and connectors, for examples, Ethernet cable and power jack. 4. Done.
Chapter 8. IPwizard Installation and operation 8.1 IPwizard Installation 1. Insert the bundled CD into the CD-ROM drive to launch the autorun program. Once completed, a welcome menu screen will appear. 2. Click the “IPwizard Utility” hyperlink; you will see the InstallShield Wizard dialog box as below. Note If the welcome screen does not appear, click “Start” at the taskbar. Then, select “Run” and type “D:\Utility\setup.exe”, assume D is your CD-ROM drive. 3.
4. Please click “Next” to install with original settings, or you may click “Change…” button to modify the install folder then press “Next” to continue. 5. Please click “Install” to start the installation.
6. Please click “Finish” to complete the installation 7. Please double-click the utility icon utility. on the desktop then you will see the 8. Press “Search” button. IP Wizard will list all IP Cameras in your LAN environment: Note Please connect you camera or video server to PC directly, and use IP Wizard to search IP address of device, when you use device at first time or forget IP address.
8.2 Wizard function Please select your device and press “Wizard”. The utility featured of “Wizard” function to help user to initial device. User can setup IP address, username and password step by step. Please enter User Name and Password. Default Username is: admin, leave password blank. Then click “Submit”.
8.3 Username and Password You may change the ID and assign a new password to your device or keep the original and press “Next” to continue. Note If you assign new password to your device, please write down and avoid forgetting it. You can select “Static IP” and enter the IP settings. Or select “DHCP ON” when there is a DHCP server in your network. If no IP address is assigned after 30 seconds, device will use its default address 192.168.0.20. User may open your web browser, and key in http://192.168.0.
Chapter 9. Cam Viewer Installation Note The Cam Viewer Pro 30 days trial version installation steps are similar. Below is the installation of Cam Viewer Lite. 1. Insert the bundled Cam Viewer CD disk into the CD-ROM drive to launch the autorun program. Once completed, a welcome menu screen will appear. Click the “Cam Viewer Lite” hyperlink, the below InstallShield Wizard dialog box will appear. Note If the welcome screen does not appear, click “Start” at the taskbar.
3. The “Welcome to the InstallShield Wizard for Planet Cam Viewer Lite 1.0.3” will display on the screen, please click “Next”. 4.
5. Please key in user name and company name for which you want and click “Next” to continue installation. 6. Check the option “Complete” – all program features will be installed (Requires the most disk space) and click “Next” to continue installation.
7. “Ready to Install the Program” will appear to prompt you to start the installation. Please click “Install” to start. 8. Please click “No” to finish the Cam Viewer Lite installation. 9. Note In above step, when Cam Viewer works with MBM5 (Motherboard Monitor 5), Cam Viewer will display CPU temperature and fan speed. Please click “Yes” if you need this function and refer to the manual of Cam Viewer CD disk for complete installation.
Appendix A: Feature Listing for Cam Viewer Software Version Cam Viewer Lite Cam Viewer Pro 32 16 / 32 / 64 - V Smart Guard - V I/O Device V V Hotline - V Address Book - V Unusual event System log Unusual event System log Counting application - 2 way counting IP Camera Input Dual Monitor Log Viewer Counting Application Remote Playback Server Concurrent Playback Counting Function Smart Search Remote Live Viewer 30 - Unlimited 1 Channel 16 Channels - V General Motion General
Appendix B: Suggest Hardware / System Requirement Total FPS ~600 600~480 480~240 240~120 120~ CPU Intel Core 2 Duo QX6800 Intel Core 2 Duo E6600 Intel Pentium D 930 Intel P4 3.0 GHz Intel P4 2.8 GHz RAM 4 GB 2 GB 2 GB 1 GB 1 GB Chipset of Motherboard Intel 946 or 965 chip, Intel Chipset recommended VGA Card ATI Radeon 9200, nVIDIA GeForce FX-5200, Intel 945/965 or above (ATI recommended) Ethernet 100 Base-TX or Above, Gigabit LAN recommended Hard Disk 160 GB or above O.S.
Ordering Information for Cam Viewer Pro Model Description CVP-16 16-Channel Cam Viewer Professional CVP-32 32-Channel Cam Viewer Professional CVP-64 64-Channel Cam Viewer Professional Further Configuration If you want to configure more detail settings of ICA-310, ICA-312, ICA-350, ICA525, ICA-530 and IVS-110, please refer to the user manual in the CD disk.
