Internet Video Server and Camera IVS-110 / ICA-310 / ICA-312 / ICA-350 / ICA-525 / ICA-530 / ICA-120 Quick Installation Guide
Table of Contents Chapter 1. Introduction..................................................................................... 3 1.1 Before Installation.................................................................................. 3 Chapter 2. IVS-110 – 1-Channel Internet Video Server........................................ 4 2.1 Package Content.................................................................................... 4 2.2 Physical Installation ................................................
7.1 Package Content...................................................................................19 7.2 Identification of Cables..........................................................................19 7.3 Physical Installation...............................................................................21 Chapter8. ICA-120 CMOS Box Internet Camera..................................................22 8.1 Package Content.................................................................................
Chapter 1. Introduction Thank you for purchasing the IP surveillance product. It is versatile and high image solution of the perfect indoor / outdoor surveillance application. The IP surveillance state-of-art design is considerable to fit in various network environments. 1.1 Before Installation Before installation, please be sure to read this quick installation guide and user’s manual (CD) carefully to complete machine installation. This QIG includes the following chapter: • Chapter 2.
Chapter 2. IVS-110 – 1-Channel Internet Video Server 2.1 Package Content IVS-110 x 1 Power Adapter x 1 Power Cable x 1 CD Disk x 1 Quick Installation Guide x 1 Note 1. If any of the above items are missing, please contact your dealer immediately. 2. Using a power supply with a different voltage that the one included with the IVS-110 will cause damage and void the warranty for IVS-110. 2.2 Physical Installation 2.2.
Video-in Jack You can install an analog camera and connect it to video-in jack. 12V DC-Out Jack The output power is 12V DC. This is used to supply 12V DC power to one external camera. The output power is 12V DC, 400mA maximum. The output power still supplies 12 V DC, 400mA power to one external, when the IVS-110 obtains power from PoE switch. DI/DO/RS-485 Connector This IVS-110 provides a general I/O terminal block with one digital input and one output for device control.
12V DC-in Jack The input power is 12V DC. Note Only use the power adapter supplied with IVS-110. Otherwise, the product may be damaged. 2.2.3 Installation Steps 1. Attach video source to IVS-110 To use IVS-110, user must supply video source to IVS-110. Connect the BNC terminal of camera to the IVS-110’s video input and make sure to power on camera first. 2.
Chapter 3. ICA-310 – 30M Infrared Internet Camera 3.1 Package Content ICA-310 x 1 Power Adapter x 1 Wall Mount Accessories x 1 CD Disk x 1 Quick Installation Guide x 1 Note 1. if any of the above items are missing, please contact your dealer immediately. 2. Using a power supply with a different voltage that the one included with the ICA-310 will cause damage and void the warranty for ICA-310. 3.2 Physical Installation 1.
3. Identification of ICA-310 cables ó RS485 cables (Blue: D+ / Red: D- ) - To connect to P/T scanner. ó Power Connector – Connect to DC 12V power adapter. ó BNC connector – For analog video output. ó RJ-45 Connector – For connect a CAT5 cable to hub or switch. The RS-485 of ICA-310 is master that can control external scanner.
Chapter 4. ICA-312 – 25M Infrared Internet Camera 4.1 Package Content ICA-312 x 1 Power Adapter x 1 Wall Mount Accessories x 1 CD Disk x 1 Quick Installation Guide x 1 Note 1. if any of the above items are missing, please contact your dealer immediately. 2. Using a power supply with a different voltage that the one included with the ICA-312 will cause damage and void the warranty for ICA-312. 4.
Local Video output (BNC port): The Network Camera also provides composite video output. User can use BNC video cable to connect the Network Camera with a TV monitor or VCR. DC-in Jack: The input power is 12VDC. Note that supply the power to the Network Camera with standard power adapter included in package. Otherwise, the improper power adapter may damage the unit and result in danger. RJ45 LAN socket: Connect to PC or Hub/Switch. For connect to 10Base-T Ethernet or 100Base-TX Fast Ethernet cabling.
Chapter 5. ICA-350 – 30M Infrared Internet Camera 5.1 Package Content ICA-350 x 1 Power Adapter x 2 (one for ICA-350, another for heater) Wall Mount Accessories x 1 CD Disk x 1 Quick Installation Guide x 1 Screws with plastic washer x 2 Minor pad x 1 L wrench x 1 Note 1. if any of the above items are missing, please contact your dealer immediately. 2. Using a power supply with a different voltage that the one included with the ICA-350 will cause damage and void the warranty for ICA-350. 5.
RJ-45 LAN Connector For connect a LAN cable to your Hub/Switch. The LAN port is a RJ-45 connector for connections to 10Base-T Ethernet or 100Base-TX Fast Ethernet cabling. This Ethernet port built N-Way protocol can detect or negotiate the transmission speed of the network automatically. Please use Category 5 “straight” cable to connect the ICA-350 to a 100Mbps Fast Ethernet network switch or hub.
Chapter 6. ICA-525 – 20M IR Vandal Proof Dome Internet Camera 6.1 Package Content ICA-525 x 1 Power Adapter x 1 Screws x 4 Telephone box x 1 L-Wrench x 1 CD Disk x 1 Quick Installation Guide x 1 Note 1. if any of the above items are missing, please contact your dealer immediately. 2. Using a power supply with a different voltage that the one included with the ICA-525 will cause damage and void the warranty for ICA-525. 6.
1. RJ-45 LAN socket: Connect to PC or Hub/Switch. For connect to 10Base-T Ethernet or 100Base-TX Fast Ethernet cabling. This Ethernet port built N-Way protocol can detect or negotiate the transmission speed of the network automatically. Please use Category 5 “straight through” cable to connect the ICA-525 to a 100Mbps Fast Ethernet network switch or hub. Note In case you need to connect the device to PC or notebook directly, you should use cross over cable instead. 2.
6.3 Physical Installation 1. Use the provided L-wrench, loosen the tamper-resistant housing cover (with screws still attached on the cover). The unit has factory installed side conduit entry and one may adjust the cables to back conduit entry according to installation requirement. Note During the installation, please take care and avoid crash. That may cause people hurt and this device damage. 2.
3. Set the proper image by moving the camera body and set the focus by turning the lens to left or right direction. Note 1. Vari-Focal Dome Operation Guide: Once the picture appears on the monitor, open the cover and adjust the lens wrench to “NEAR © ™ FAR”, get the view zoom that you desire, and then adjust the focus wrench of the lens to obtain the best picture. After adjustment, tighten both wrenches. 2. You may power on the ICA-525 and connect it to a monitor template for adjust the image. 3.
5. When using the side conduit cabling, it is suggested to cover the cables using metal covers (to prevent external damage and for waterproof prevention), and wined the waterproof adhesive type onto the metal cover before installation. 6. Connect the LAN cable to Ethernet’s switch or hub and the DC-Jack to the power source. The video output to monitor or other video through a 75 Ohms type coaxial cable if you will use BNC cable. 7.
Chapter 7. ICA-530 – 15M IR Dome Internet Camera 7.1 Package Content ICA-530 x 1 Power Adapter x 1 Wrench x 1 Telephone box x 1 CD Disk x 1 Quick Installation Guide x 1 Note 1. if any of the above items are missing, please contact your dealer immediately. 2. Using a power supply with a different voltage that the one included with the ICA-530 will cause damage and void the warranty for ICA-530. 7.
1. RJ45 LAN socket Connect to PC or Hub/Switch. For connect to 10Base-T Ethernet or 100BaseTX Fast Ethernet cabling. This Ethernet port built N-Way protocol can detect or negotiate the transmission speed of the network automatically. Please use Category 5 “straight through” cable to connect the ICA-530 to a 100Mbps Fast Ethernet network switch or hub. Note In case you need to connect the device to PC or notebook directly, you should use cross over cable instead. 2.
6. Line out (audio out) Connect a loud speaker to the ICA-530. This function is for voice alerting and two-way audio. 7.3 Physical Installation 1. Drill 20mm (3/4”) holes in the ceiling or wall and then align the mounting plate to the holes you have made as below. Ceiling Top Plate Directly install on any horizontal or vertical surface 2. Camera Adjustment: Tilting View Rotating View Panning View Angle range is 0o~90o Angle range is 0o~180o Angle range is 0o~180o 3.
Chapter8. ICA-120 CMOS Box Internet Camera 8.1 Package Content ICA-120 x 1 Power Adapter x 1 Camera Mount Kit x 1 CD Disk x 1 Quick Installation Guide x 1 Note 1. If any of the above items are missing, please contact your dealer immediately. 2. Using a power supply with a different voltage that the one included with the ICA-120 will cause damage and void the warranty for ICA-120. 8.2 Physical Description 8.2.
8.2.2 Rear View Audio Output Jack DC Power Jack Factory Default Reset LAN Socket DI/DO Connector External MIC Jack Power & LAN LED Audio Output Jack Audio-out Jack allows this device to output audio for two-way communication or alerting sound. DC Power Jack The input power is 12VDC. Note Only use the power adapter supplied with ICA-120. Otherwise, the product may be damaged. LAN Socket The LAN socket is a RJ-45 connector for connections to 10Base-T Ethernet or 100Base-TX Fast Ethernet cabling.
Power & LAN LED (green color) This LED is used to indicate whether DC power is on or not. In addition, this LED will be flashing while network accessing via Ethernet. DI/DO Connector The Camera provides a terminal block with 4 pins of connectors for DI and DO. Please refer to the Appendix B in this manual for more information. External Microphone The Camera also supports external microphone. User can plug in an external microphone to pick up voice more.
Chapter 9. IP Wizard Installation and operation This chapter shows how to quick set up your IP surveillance product. The IP surveillance product is with the default settings. However to help you find the networked camera quickly the windows utility-IP Wizard can search the cameras in the network that shall help you to configure some basic setting before you started advanced management and monitoring. 9.1 IP Wizard Installation Note In the installation steps below, this guide use ICA-310 as the example.
4. The “Welcome to the InstallShield Wizard for IPWizard” will display on the screen and click “Next” to continue. 5. Please click “Next” to install with original settings, or you may click “Change…” button to modify the install folder then press “Next” to continue.
6. Please click “Install” to start the installation. 7.
8. Please double-click the utility icon utility. on the desktop then you will see the 9. Press “Search” button. IP Wizard will list all IP Cameras in your LAN environment: Note Please connect you camera or video server to PC directly, and use IP Wizard to search IP address of device, when you use device at first time or forget IP address. 9.2 Wizard function Please select your device and press “Wizard”. The utility featured of “Wizard” function to help user to initial device.
Please enter User Name and Password. Default Username is: admin, leave password blank. Then click “Submit”. 9.3 Username and Password You may change the ID and assign a new password to your device or keep the original and press “Next” to continue. Note If you assign new password to your device, please write down and avoid forgetting it.
You can select “Static IP” and enter the IP settings. Or select “DHCP ON” when there is a DHCP server in your network. Note If no IP address is assigned after 30 seconds, Internet Camera will use its default address 192.168.0.20. User may open the web browser, and key in the IP address (for example: http://192.168.0.20, the default IP address) in the address field to login web configuration page and refer to the User’s manual in the bundled CD disk for more configuration.
Chapter 10. Cam Viewer Plus Installation Note The Cam Viewer Plus Pro 30 days trial version installation steps are similar. Below is the installation of Cam Viewer Plus. Insert the bundled CD disk into the CD-ROM drive to launch the autorun program. Once completed, a welcome menu screen will appear. Click the “Cam Viewer Plus” hyperlink, the below InstallShield Wizard dialog box will appear. Note If the welcome screen does not appear, click “Start” at the taskbar.
The “Welcome” window will then pop-up, click on “Next” to continue. You may choose where to install the program. Click on “Change” button to browse your computer. Once you have specified the directory, click on “Next” to continue.
You are now ready to install the program. Click on “Install” to begin the installation process. You will now see the installation progress. Please wait a few minutes to complete the installation.
Click on “Finish” to exit the InstallShield wizard. You will now be prompted to create an administrator account. This account allows full control of Cam Viewer Plus Pro. Enter a password for this administrator account in the “Password” field and re-enter it in “Password Confirm” field.
You will then be prompted to login by the administrator user name and password. Enter “administrator” in the “User Name” field. Enter the password you just created in the “Password” field. You have successfully entered Cam Viewer Plus.
Appendix A: Feature Listing for Cam Viewer Plus Specification Description Cam Viewer Plus Pro Cam Viewer Plus Up to 64 channels Live view channel Max. channels monitored simultaneously Up to 64 channels E-Map Showing camera's location and map background V N/A Remote Server Provide remote server, support remote live view V N/A Counting Function Provide counting function V N/A Compression format H.
Appendix B: Suggest Hardware / System Requirement The Minimum system requirement CPU Intel® Pentium 4 3.0GHz with Hyperthreading RAM 1 GB Video RAM 128MB Display Chip nVIDIA GeForce 8500GT ATI Radeon HD 4350 Display Resolution 1024X768 24bits Operating System Windows2000 SP4 / Windows XP Pro SP2 / Windows 2003 /Vista DirectX 9.
Ordering Information for Cam Viewer Plus Pro Model Description CVPP-4 4-Channel Cam Viewer Plus Pro CVPP-9 9-Channel Cam Viewer Plus Pro CVPP-16 16-Channel Cam Viewer Plus Pro CVPP-25 25-Channel Cam Viewer Plus Pro CVPP-36 36-Channel Cam Viewer Plus Pro CVPP-49 49-Channel Cam Viewer Plus Pro CVPP-64 64-Channel Cam Viewer Plus Pro Further Configuration If you want to configure more detail settings of ICA-120, ICA-310, ICA-312, ICA350, ICA525, ICA-530 and IVS-110, please refer to the user manu
This page is intentionally left blank
This page is intentionally left blank
