en USER MANUAL Portable Air Conditioner Rated voltage: 115V Frequency: 60Hz Warning notices: Before using this product, please read this manual carefully and keep it for future reference. The design and specifications are subject to change without prior notice for product improvement. Consult with your dealer or the manufacturer for details. PAP10R1BWT PAP12R1BWT PAP14R1BWT Customer service: 1(866)-646-4332 www.pelonis.
Owner’s Manual Safety Precautions ........................................................................................ 3 Unit Specifications and Features ............................................................... 6 Operating Instructions ................................................................................. 7 Installation Instructions ............................................................................... 12 Care and Cleaning ......................................................
Safety Precautions Safety Precautions To prevent injury to the user or personal and property damage, these instructions must be followed. Incorrect operation due to ignoring of instructions may cause harm or damage. The level of risk is shown by the following indications. This symbol indicates the possibility of death or serious injury. WARNING This symbol indicates the possibility of injury or damage to property. CAUTION WARNING This symbol shows that this appliance uses a flammable refrigerant.
Safety Precautions WARNING • DO NOT install your air conditioner in a wet room such as a bathroom or laundry room. Exposure to water can cause electrical components to short circuit. • DO NOT install the unit in a location that may be exposed to combustible gas, as this could cause fire. • The unit has wheels to allow it to move. Do not attempt to roll the unit across thick carpet or to roll over objects, as this could cause the unit to tip over.
Safety Precautions Safety Precautions WARNINGS (for using R32 refrigerant only) • Do not use any means to accelerate the defrosting process or to clean the unit, other than those recommended by the manufacturer. • Do not use or store the appliance in spaces with potential ignition sources (for example: open flames, an operating gas appliance or an operating electric heater). • Do not pierce or burn refrigerant tubing. Be aware that refrigerants may not contain an odor.
Unit Specifications and Features Unit Specifications and Features Preparation control panel upper air filter horizontal louver blade handle (both sides) upper air intake drain outlet air outlet lower air filter lower air intake power plug socket drain outlet (only for pump heating mode) Caster front power cord outlet power cord buckle bottom tray drain outlet rear Design and Compliance Notes Design Notice: In order to ensure the optimal performance of our products, the design specifications of the u
Operating Instructions Control Panel Features Constant fan Operating Instructions Constant fan (Press 3s) Swing Button (optional) (Applicable to the models with auto swing feature only) Used to initiate the Auto Swing feature. When the operation is ON, pressing the SWING button can stop the louver at the desired angle. NOTE The control is capable of displaying temperature in degrees Fahrenheit or degrees Celsius.
Control Panel Features (cont.) NOTE After 250 hours of operation, the filter indicator light illuminates. This feature is a reminder to clean the air filter for more efficient operation. Press this button for 3 seconds to cancel the reminder. Operating Instructions Power button Power switch on/off. LED display Shows the set temperature in °C or °F and the Auto-timer settings. While on DRY and FAN modes, it shows the room temperature.
Operating Instructions DRY operation • Press the “MODE” button until the “DRY” indicator light comes on. • While in this mode, you cannot select a fan speed or adjust the temperature. The fan motor operates at LOW speed. • Keep windows and doors closed for the best dehumidifying effect. • Do not connect the duct to a window.
Other Features FOLLOW ME/TEMP SENSING Feature (optional) NOTE This feature can be activated from the remote control ONLY. The remote control serves as a remote thermostat allowing for the precise temperature control at its location. Operating Instructions To activate the Follow Me/Temp Sensing feature, point the remote control towards the unit and press the Follow Me/Temp Sensing button. The remote display is actual temperature at its location.
• During heat pump mode, remove the lower drain plug from the back of the unit and install the drain connector (5/8” universal female mender) with 3/4” hose (locally purchased). For models without drain connector, just attach the drain hose to the hole. Place the open end of the hose adaptor directly over the drain area in your basement floor. Remove the upper drain plug Continuous drain hose Make sure the hose is secure so there are no leaks.
Installation Instructions Choosing the Right Location Your installation location should meet the following requirements: • Make sure that you install your unit on an even surface to minimize noise and vibration. • The unit must be installed near a grounded plug, and the Collection Tray Drain (found on the back of the unit) must be accessible. cm h nc .7i 19 50 Installation Instructions • The unit should be located at least 12" (30 cm) from the nearest wall to ensure proper air conditioning.
Tools Needed • Medium Phillips screwdriver • Tape measure or ruler • Knife or scissors • Saw (optional, to shorten window adaptor for narrow windows). Accessories Your Window Installation Kit fits windows 67.5-123 cm (26.5”-48”) and can be shortened for smaller windows.
Window Installation Kit Exhaust hose Exhaust hose assembly Step One: Preparing the exhaust hose assembly Press the exhaust hose into the window slider adaptor and unit adaptor, clamp automatically by elastic buckles of the adaptors.
NOTE Once the Exhaust Hose assembly and Adjustable Window Slider are prepared, choose from one of the following two installation methods. Foam seal B (Adhesive type-shorter) Type 1: Hung window installation 1. Cut the adhesive foam seal A and B strips to the proper lengths, and attach them to the window sash and frame as shown. Foam seal A (Adhesive type) Window slider A Window slider B (if required) Foam seal C (Non-adhesive type) Security Bracket 3.
Foam seal B (Adhesive type-shorter) Type 2: Sliding window installation 1. Cut the adhesive foam seal A and B strips to the proper lengths, and attach them to the window sash and frame as shown. Foam seal A (Adhesive type) Window slider B (if required) 2. Insert the window slider assembly into the window opening. Window slider A Installation Instructions Foam seal C (Non-adhesive type) Security Bracket 3. Cut the non-adhesive foam seal C strip to match the window height.
Care and Cleaning Safety Precautions • • • • Always unplug the unit before cleaning or servicing. DO NOT use flammable liquids or chemicals to clean the unit. DO NOT wash the unit under running water. Doing so causes electrical danger. DO NOT operate the machine if the power supply was damaged during cleaning. A damaged power cord must be replaced with a new cord from the manufacturer.
Troubleshooting Tips Malfunction Diagnosis Please check the following troubleshooting methods before calling for service: Problem Unit does not turn on when pressing ON/ OFF button Possible Cause Troubleshooting P1 Error Code. The water collection tray is full. Turn off the unit, drain the water from the water collection tray and restart the unit. In COOL mode: room temperature Reset the temperature. is lower than the set temperature. The air filter is blocked with dust or animal hair.
Remote Control Instructions Remote Control Specifications RG57H4(B)/BGEFU1 Model Rated voltage 3.0V (Dry batteries R03/LR03x2) Signal receiving range 8 m (approx. 26 ft.) Environment 23°F ~ 140°F (-5°C ~ 60°C) Function Buttons Before you begin using your new air conditioner, make sure to familiarize yourself with its remote control. The following is a brief introduction to the remote control itself.
Handling the Remote Control NOT SURE WHAT A FUNCTION DOES? Refer to the Operating Instructions section of this manual for a detailed description of how to use your air conditioner. SPECIAL NOTE Button designs on your unit may differ slightly from the example shown. If the unit does not have a particular function, pressing that function’s button on the remote control will have no effect.
Remote LED Screen Indicators Transmission Indicator Lights up when remote sends signal to unit MODE display Displays the current mode, including: ON/OFF display Appears when the unit is turned on and disappears when it is turned off AUTO COOL DRY HEAT FAN TIMER ON display Displays when TIMER ON is set TIMER OFF display Displays when TIMER OFF is set ECO display Not available on this unit Battery display Low battery detection SLEEP display Displays when SLEEP function is activated FOLLOW ME display Indic
Basic Functions SETTING THE DESIRED TEMPERATURE The operating temperature range for this unit is 17-30°C (62°F-86°F). You can increase or decrease the set temperature in 1°C (1°F) increments. 3 1 2 AUTO operation O N /O F F SHORT CUT MODE TIMER ON In AUTO mode, the unit will automatically select the COOL, FAN, HEAT or DRY mode based on the set temperature. TIMER OFF 1. Press the MODE button to select Auto mode. T E MP FAN SLEEP FOLLOW ME SWING 2.
Basic Functions (cont.) FAN operation 1. Press the MODE button to select FAN mode. 2. Press FAN button to select the fan speed: AUTO, LOW, MED or HIGH. 3. Press the ON/OFF button to start the unit. 3 O N /O F F 1 MODE 2 FAN SHORT CUT NOTE TIMER ON T E MP SLEEP TIMER OFF FOLLOW ME SWING You cannot set temperature in FAN mode. As a result, your remote control’s LCD screen will not display temperature. LED HEAT operation 1. Press the MODE button to select HEAT mode. 2.
Timer Functions 1 2 TIMER ON x5 TIMER ON Your air conditioning unit has two timer-related functions: TIMER ON - sets the amount of time after which the unit will automatically turn on. TIMER OFF - sets the amount of time after which the unit will automatically turn off. TIMER ON function 3 1sec 4 2sec The TIMER ON function allows you to set a period of time after which the unit will automatically turn on, such as when you come home from work. 1. Press the TIMER ON button.
Timer Functions (cont.) 3. Wait 2 seconds, then the TIMER OFF function will be activated. The digital display on your remote control will then return to the temperature display. T imer on O N /O F F NOTE Continue to press TIMER ON or TIMER OFF until desired time is reached. SHORT CUT TIMER ON MODE T E MP TIMER OFF FAN SLEEP SWING FOLLOW ME 1 LED 2 TIMER ON X12 When setting the TIMER ON or TIMER OFF functions, up to 10 hours, the time will increase in 30 minute increments with each press.
Advanced Functions SLEEP Function The SLEEP function is used to decrease energy use while you sleep (and don’t need the same temperature settings to stay comfortable). This function can only be activated via remote control. Note: The SLEEP function is not available in FAN or DRY mode. O N /O F F SHORT CUT TIMER ON MODE T E MP TIMER OFF FAN SLEEP SWING FOLLOW ME LED SWING Function Used to stop or start louver movement and set the desired up/down air flow direction.
NOTES • When there are differences between features or operation implied by the remote control illustration and the actual functions described in the USER MANUAL, please refer to the descriptions in the USER MANUAL. • The device may comply with local national regulations. In Canada, it should comply with CAN ICES-3(B)/NMB-3(B). In USA, this device complies with part 15 of the FCC Rules.
Warranty Air Conditioner Limited Warranty Your product is protected by this Limited Warranty: Warranty service must be obtained from Midea Consumer Services or an authorized Midea servicer. Warranty • Two-year limited warranty from original purchase date. Five-year compressor warranty from original purchase date. Midea, through its authorized servicers will: • Pay all costs for repairing or replacing parts of this appliance which prove to be defective in materials or workmanship.
How to Stay Cool with a New Portable Air Conditioner Because of a new federal test procedure for Portable Air Conditioners, you may notice that the cooling capacity claims on portable air conditioner packaging are significantly lower than that of models produced prior to 2017. This is due to changes in the test procedure, not to the portable air conditioners themselves. What should I look for first when purchasing a portable air conditioner? The right air conditioner helps you cool a room efficiently.
