Installation Instructions

ManualsBrandsPatriot Lighting ManualsIndoor LightingLoft 1-Light Bronze Track Lighting Pendant

INSTRUCTIONS

FOR ITEM: 349-5921

1. Install a bulb (included). See relamping label at socket area or packaging for maximum allowed

wattage.

2. Attach the glass shade to the glass bracket by threading set screws onto the glass notch. (Do not over

tighten.)

Note: Follow the enclosed “Cable Length Adjustment” to adjust the length of the cable if

necessary.

WARNIGN: To avoid the risk of injury, be sure to turn off electrical power

while installing or servicing this fixture.

Adapter

Cable

For Track Mounting:

Fixture

Hardware Package:

(1 SET)

Bulb Type ST Max.60W

(included)

130829

Set Screw

Glass Bracket

Glass Shade

Notch

1-2 To mount Track, drill holes in ceiling or wall. Attach Track with

toggle bolts or screws if surface is solid material.

CAUTION: Turn off switch at main power source (fuse box)

before installing any Track or fittings.

STEP 1. Place Track over outlet box and mark position of

Track mounting holes on ceiling or wall. On wallboard or

plaster, drill 5/8" mounting holes and install Track to ceiling

or wall using toggle bolts. On wood surfaces, use Dry Wall

Screws.

STEP 2. Install mounting adapter and power fittings.

STEP 3. Switch on main power.

CAUTION: Disconnect power before installation.

To attach mounting adapter to the Track, align the polarity

lines of the Track and the polarity lines of the mounting

adapter. Push top portion of the adapter with contact

fingers into the slot in the Track and turn 90 (if the adapter

does not turn easily, do not force, but turn in other

direction.) To remove, depress the release lever with the

index finger and turn 90 .

Note: If the polarity lines of the Track and the polarity lines of

the mounting adapter don't match, the light won’t be working.

MOUNTING ADAPTER INSTALLATION

ASSEMBLY INSTRUCTIONS

MOUNTING ADAPTER

TRACK

(not included)

POLARITY LINE

Track mounting holes

Plain underside of Track faces ceiling or wall

Open,slotted side of Track faces

OUT to accept lights

Dead end fitting with

set screw

TRACK

(not included)

Track

(not included)

Summary of content (4 pages)

PAGE 1
INSTRUCTIONS FOR ITEM: 349-5921 WARNIGN: To avoid the risk of injury, be sure to turn off electrical power while installing or servicing this fixture. ASSEMBLY INSTRUCTIONS Hardware Package: (1 SET) Track (not included) Adapter Cable Fixture Glass Bracket Set Screw CAUTION: Turn off switch at main power source (fuse box) before installing any Track or fittings. STEP 1. Place Track over outlet box and mark position of Track mounting holes on ceiling or wall.
PAGE 2
INSTRUCTIONS Cable Length Adjustment 1. Remove the adapter cover from the adapter holder by loosening the set screws (Figure 1). Remove the slide pad and spring, and set them aside. Set Screw Adapter Cover 2. Unscrew the wire nuts and separate the wires (Figure 1). Slide Pad Adapter Holder 1 Strain Relief A A Strain Relief 1" A A 3-c 5. Pull the cable down until the strain relief hits the bottom of the adapter holder.
PAGE 3
Figure.1 Outlet Box D(3/8") Wire Nut C(3") Adapter Screw B(9") Lock Nut Strain Relief Mounting Screw Canopy Cable Ball Nut Flat Head Screwdriver Headless Screw A For Ceiling Mounting: Mounting Strap Figure.2 Cable 1. Cut off the cable near the bottom of the adapter. (See Figure 1) 2. Thread the cable through the canopy and two holes of the strain relief in order. Fixture 3.
PAGE 4
In case of damaged or missing parts, please call toll-free at 1-800-887-6326 Contents of Spare Parts: Assembly Kit (1 SET) (4828MM) Glass Shade (1 PC) (9482C) Bulb (1 PC) (8058EB) 5-YEAR LIMITED WARRANTY: This Patriot Lighting fixture carries a limited warranty against defects in material or workmanship.