Owners Manual / Installation Guide

ManualsBrandsMTI Baths ManualsBathroom SinksAkana 24-1/4" Rectangle SculptureStone Undermount Bathroom Sink with 3 Faucet Holes

Table Of Contents

1. Place sink in desired location and mark drain opening on countertop.

2. Mark a 4-6" cutout for drain assembly. The cutout has to be just large enough so that the drain assembly can be

tightened directly onto the sink. If faucet is to be mounted to sink, allow additional clearance for supply lines.

3. Check for correct drain location by temporarily placing sink on counter.

4. If faucetry will be installed on the sink, drill appropriate sized hole(s) for valve(s) using a standard hole saw.

5. Remove sink from counter and install the drain and faucet assemblies.

6. Apply a thin bead of clear silicone or matching tub and tile caulk to the bottom edge of the sink and secure to

countertop. We recommend the use of silicone in lieu of plumber's putty under the flange of the lavatory drain.

7. Place the sink onto the desired location and allow silicone to cure.

8. Connect the supply lines and drain pipes; then test for leaks.

Installation instructions for semi-recessed lavatory sinks.

1. Place template(s) in desired location and mark line for cutout.

2. Cut countertop using appropriate tools for countertop material.

3. Set sink in place. Note: if sink does not fit properly, lift sink and rotate 180 degrees.

4. Install drain and faucet. We recommend the use of silicone in lieu of plumber's putty under the flange of the lavatory

drain.

5. Test for plumbing leaks.

6. Apply a thin bead of clear silicone or matching tub and tile caulk to the edge of the sink where it meets the countertop.

You may also apply around the underside of the vanity to ensure a water-tight seal.

7. Let silicone or caulk cure for 24 hours before use.

Installation instructions for undermount sinks.

MTI does not provide templates for undermounting. Please have the product on site for the solid surface fabricator.

1. The sink can be fixed to the top using the color matched glue appropriate for the solid surface material being used for

the top.

2. Lay the top face down, and use the counter top glue to attach sink. Allow to set.

3. Complete routing and sanding where countertop meets the sink.

4. Alternatively, the sink can sit on a ledge underneath the vanity counter top. Seal the top seam with color matched

caulk or clear silicone. The fabricator may use the glue appropriate to the counter top material.

5. Install drain and faucet. We recommend the use of silicone in lieu of plumber's putty under the flange of the lavatory

drain.

6. Test for plumbing leaks.

7. Let silicone or caulk cure for 24 hours before use.

Boutique Collection - SculptureStone™ Lavatory Sinks

MTI’s SculptureStone™ sink bowls are designed to accommodate nearly any properly sized lavatory drain kit. Because of

variations in lavatory drain design styles, the following drain installation information is provided:

• Contact area from drain to sink requires careful installation to seal properly.

• MTI recommends the use of a proper water sealant product, such as silicone, in lieu of plumber’s putty under the

waste flange at the contact area.

• Insufficient sealant on installation may result in over tightening in an attempt to achieve a better seal at the contact

area.

• Over tightening will create excessive stress at the contact point which can result in compression cracks over time.

Compression cracks are not considered a defect of material and will void the product’s warranty.

Recommendations:

1. Use sealant (Silicone) generously near and at the contact area and tighten. Typical tightness – snug plus an eighth to

a quarter turn.

2. Allow time for sealant to cure before water testing.

Installation instructions for semi-recessed countertop sinks

Summary of content (9 pages)

PAGE 1
Boutique Collection - SculptureStone™ Lavatory Sinks MTI’s SculptureStone™ sink bowls are designed to accommodate nearly any properly sized lavatory drain kit. Because of variations in lavatory drain design styles, the following drain installation information is provided: • Contact area from drain to sink requires careful installation to seal properly. • MTI recommends the use of a proper water sealant product, such as silicone, in lieu of plumber’s putty under the waste flange at the contact area.
PAGE 2
Boutique Collection - SculptureStone™ Installation - Lavatory Sinks & Counter-Sinks IMPORTANT! Read all instructions carefully before beginning installation or drilling of sink. Installation instructions for wall-mounted Counter-Sinks. 1. Attach carrier arms to wall studs using the hardware supplied. MTI recommends using all the supplied bolts for maximum strength. 2.
PAGE 3
Installation Instructions for Incline Sink The Incline sink uses a unique slot drain that does not have any exposed drain components on top. The incline sink is available as an undermount sink or as an MTI counter-sink. The incline sink is not for top mount, or self rimming applications. This feature requires a special drain trough assembly ** below to catch water and needs to be installed per the following instructions.
PAGE 4
2) Install drain assembly onto trough so it looks like this: **This drain assembly does not have grates by design so objects can move easily to P-trap and no clogging at drain will occur. 3) Once the drain and trough are assembled and the surfaces cleaned, put a thick bead of clear silicone adhesive on the trough lip (shown above in picture) all the way around the entire perimeter. 4) Place trough onto sink bottom (flat area) making sure that the trough completely covers the slot opening in the sink.
PAGE 5
Care & Cleaning: Once installed, the area of the Drain Pan should be periodically flushed with hot water and bleach, usually 10:1 is sufficient (10 parts water, 1 part bleach). Let the bleach 'flush' sit for about 10 minutes, and then flush again with clean hot water. This will keep the Drain Pan area clean and free of mildew. An alternative to bleach is to use straight hydrogen peroxide (3% solution). Pour hydrogen peroxide into the Drain Pan, trying to get the solution into all areas of the Drain Pan.
PAGE 6
Installation Instructions for Petra/Halo Pedestal Sink 1) Install faucet and drain using access area in back of pedestal 2) Attach steel braided hose and P-trap on drain so they are ready for connections to wall. Cut p-trap tubing to correct size. 3) Set pedestal using included adjustable feet to make sure the pedestal sits on the floor level with as little a gap as possible to the floor.
PAGE 7
4) Reach behind pedestal and connect water supplies to angle stops and P-trap compression nut. Turn angle stops fully open. Now turn faucet on and check for leaks at stops and drain/p-trap. 5) Make slight adjustments to the pedestal to get position correct. The pedestal can be pushed slightly toward the wall if a tighter look is desired. Make sure drain and faucet connections remain intact after adjustments. 6) Optionally, the bottom edge can be sealed to the floor with a sealant.
PAGE 8
Boutique Collection - SculptureStone™ Care and Cleaning - Lavatory Sinks and Counter-Sinks CARE AND CLEANING INSTRUCTIONS For Matte Finish The SculptureStone™ (ESS) surface of all MTI Boutique Collection lavatory sinks is among the highest quality surfaces available. Its hard, non-porous surface prevents dirt from accumulating and resists stains better than other materials. With normal use, the ESS will retain its beauty with only a minimal amount of care.
PAGE 9
Boutique Collection - SculptureStone™ Warranty - Lavatory Sinks and Counter-Sinks Residential Warranty This warranty is effective for all MTI SculptureStone™ (ESS) sinks manufactured after January 1, 2007, and is in lieu of all other warranties. MTI Baths provides a limited five year warranty on sinks for use in the continental United States to the original purchaser for personal or single family use. Warranty begins on date of purchase (regardless of installation date).