Model Model Model Model M20 M27 M30 M34 How to install, operate and maintain your Demand Controlled Water Softener Do not return water softener to store If you have any questions or concerns when installing, operating or maintaining your water softener, call our toll free number: 1-888-64 WATER (1-888-649-2837) Monday- Friday, 8 AM - 7 PM EST or visit www.systemsaver.
For best results use Morton® System Saver® II Pellets to soften your water Morton® System Saver® II Pellets offer superior performance and convenience. Morton® System Saver® II Pellets are created from high purity salt combined with resin cleaning additives. Specially formulated to outperform other water softening salts, System Saver® II is complete with a patented formula that helps keep your softener clean, problem-free and running longer.
TABLE OF CONTENTS Page Inspect Shipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Specifications & Performance Claims . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Inspect Shipment The parts required to assemble and install the unit are included in a bag. Thoroughly check the water softener for possible shipping damage and parts loss. Also inspect and note any damage to the shipping carton. Remove and discard (or recycle) all packing materials. To avoid loss of small parts, we suggest you keep the small parts in the parts bag until you are ready to use them.
Specifications & Performance Claims Model Code Regeneration Control Rated Softening Capacity (Grains @ Salt Dose) Rated Efficiency (Grains/Pound of Salt @ Minimum Salt Dose) Water Used During Regeneration @ Minimum Salt Dose Total Water Used Per Regeneration @ Maximum Salt Dose Rated Service Flow Rate Amount of High Capacity Ion Exchange Resin Pressure Drop at Rated Service Flow Water Supply Max. Hardness Water Supply Max. Clear Water Iron Water Pressure Limits (min. / max.) Water Temperature Limits (min.
Before You Start = The water softener requires a minimum water flow of 3 gallons per minute at the inlet. Maximum allowable inlet water pressure is 125 psi. If daytime pressure is over 80 psi, nighttime pressure may exceed the maximum. Use a pressure reducing valve if necessary (Adding a pressure reducing valve may reduce the flow). If your home is equipped with a back flow preventer, an expansion tank must be installed in accordance with local codes and laws.
Installation Requirements Location Requirements Plumbing Codes Consider all of the following when selecting an installation location for the water softener. All plumbing must be completed in accordance with national, state and local plumbing codes. = Do not locate the water softener where freezing temperatures occur. Do not attempt to treat water over 120ºF. Freezing temperatures or hot water damage voids the warranty.
Installation Requirements Valve Drain Requirements 1/4” NPT Thread Barbs for 3/8” I.D. Tubing Using the flexible drain hose (included), measure and cut to the length needed. Flexible drain hose is not allowed in all localities (check your plumbing codes). If local codes do not allow use of a flexible drain hose, a rigid valve drain run must be used. Purchase a compression fitting (1/4 NPT x 1/2 in. minimum tube) and 1/2" tubing from your local hardware store. Plumb a rigid drain as needed (See Figure 6).
Installation Instructions Typical Installation To Outside Faucets Hard Water r Pipe Main Wate Conditioned Water Pipe Clips Water Softener Valve 1” NPT Sweat Adaptor (not included) To Controller Outlet Plug-in Power Supply O-ring Inlet Overflow Drain Elbow Valve Drain Elbow Salt Storage Tank Overflow Hose* Valve Drain Hose* *Do not connect the water softener valve drain hose to the salt storage tank overflow hose.
Installation Instructions continued from previous page Top Cover 2. Visually check and remove any debris from the water softener valve inlet and outlet ports. 3. Make sure the turbine assembly spins freely in the "out" port of the valve (See Figure 10). 4. If not already done, put a light coating of silicone grease on the single bypass valve o-rings. 5. Push the single bypass valve into the softener valve as far as it will go.
Installation Instructions Step 5. Cold Water Pipe Grounding CAUTION: The house cold water pipe (metal only) is often used as a ground for the house electrical system, The 3-valve bypass type of installation, shown in Figure 8, will maintain ground continuity. If you use a plastic bypass valve at the unit, continuity is broken. To restore the ground, do the following: 1.
Installation Instructions continued from previous page bypass valve body toward the softener (See Figure 15). Improper removal may damage clips. Do not reinstall damaged clips. If removing clips... ...depressurize the plumbing, then push Bypass Valve body toward softener FIG. 15 Step 9. Add Water and Salt to the Salt Storage Tank 1. Using a container, add about three gallons of clean water into the salt storage tank. 2. Add Morton® System Saver® II Pellets to the storage tank.
Programming the Water Softener (Models M20, M27 & M30) UP button Display DOWN button RECHARGE button SELECT button When the power supply is plugged into the electrical outlet, a model code and a test number (example: J2.0), begin to flash in the faceplate display. Then, “12:00 PM” and the words “PRESENT TIME" begin to flash.
Programming the Water Softener (Models M20, M27 & M30) Step 3. Set Recharge (Regeneration) Time Your demand water softener will automatically regenerate when it needs to, based on water usage. The time of day that the automatic recharge cycle begins may be changed as follows: 1. Press the SELECT button once again to display a flashing “2:00AM” and the words “RECHARGE TIME”. This is a good time for the recharge to start in most households, because water is not in use. FIG. 19 2.
Customizing Features / Options (Models M20, M27 & M30) Recharge Now Adjustable Backwash At times of greater than normal water use, such as when you have guests, you could run out of conditioned water before the next scheduled recharge. If this happens, you may want to initiate an immediate regeneration, as follows: If your incoming water supply has higher sediments or clear water iron, a longer Backwash and/or Fast Rinse time may help in keeping the unit cleaner. 1.
Programming the Water Softener (Model M34) Low Salt LED Indicator Display UP button RECHARGE button SELECT button DOWN button When the power supply is plugged into the electrical outlet, a model code and a test number (example: J2.0), begin to flash in the faceplate display. Then, “12:00 PM” and the words “SET TIME" begin to flash.
Programming the Water Softener Step 4. Set Salt Level The water softener has a low salt indicator light to remind you to refill the storage tank with salt. NOTE: You must set salt level each time salt is added to the water softener. To set this monitor system: 1. Lift the salt lid and level the salt in the storage tank. 2. The salt level scale, on the brinewell inside the tank, has numbers from 0 to 8 (See Fig. 32). Observe the highest number the leveled salt is at, or closest to.
Customizing Features / Options (Model M34) Recharge Now Adjustable Backwash At times of greater than normal water use, such as when you have guests, you could run out of conditioned water before the next scheduled recharge. If this happens, you may want to initiate an immediate regeneration, as follows: If your incoming water supply has higher sediments or clear water iron, a longer Backwash and/or Fast Rinse time may help in keeping the unit cleaner. 1.
Customizing Features / Options (All Models) Power Outage Memory If electrical power to the softener is interrupted, the time display is blank, but the electronic controller keeps correct time for several hours. When power is restored, you must reset the present time only if the display is flashing. All other settings are maintained and never require resetting unless a change is desired.
Routine Maintenance Cleaning the Nozzle & Venturi A clean nozzle & venturi (See Figure 42) is a necessity for the water softener to work properly. This small component creates the suction to move brine from the brine tank, into the resin tank. If it should become plugged with sand, silt, dirt, etc., the water softener will not work, and hard water will result.
Troubleshooting Automatic Electronic Diagnostics This water softener has a self-diagnostic function for the electrical system (except input power and/or water meter). The water softener monitors electronic components and circuits for correct operation. If a malfunction occurs, an error code appears in the display. letter appears, the switch is closed. If the dash shows, the switch is open. Water Meter FIG. 44 While an error code appears in the display, all buttons are inoperable except the SELECT button.
Troubleshooting Resetting to Factory Defaults To reset the electronic controller to its factory default for all settings (time, hardness, etc.): 1. Press the SELECT button and hold it until the display changes twice to show “CODE” and the flashing model code. 2. Press the p UP button (a few times, if necessary) to display a flashing “SoS”. Models M20, M27 & M30 Model M34 If water does not enter the tank, look for an obstructed nozzle, venturi, fill flow plug, brine tubing, or brine valve riser pipe. 2.
Notes Morton® System Saver® Installation & Operation Manual 23
Softener Exploded View 13 14 12 Valve Assembly See Pages 26 & 27 for parts 15 27 11 17 1 2 16 4 6 3 18 19 7 8 7 25 20 6 5 5 21 8 10 26 9 22 23 24 24 Morton® System Saver® Installation & Operation Manual
Softener Parts List Key No. Part No. Description – 7112963 1 á Distributor O-Ring Kit (includes Key Nos. 1-3) 3 á 2 á 4 7077870 – 7331177 6 á 5 7 8 7105047 á 7114787 7264922 9 0502272 11 7330977 10 12 13 14 ¢ 7331143 7330985 7331371 7331630 7330993 7331339 7331614 O-Ring, 2-7/8” x 3-1/4” O-Ring, 13/16” x 1-1/16” O-Ring, 2-3/4” x 3” Top Distributor Repl. Bottom Distributor Tank Neck Clamp Kit (includes Key Nos. 6 & 7) Clamp Section (2 req.) Retainer Clip (2 req.) Repl.
Valve Exploded View 50 51 70 52 91 53 90 87 56 57 89 86 88 85 59 60 58 61 84 66 83 67 82 70 62 81 63 80 64 76 65 78 55 54 79 68 69 71 77 74 Wear Strip Seal Cross-section View 26 75 Morton® System Saver® Installation & Operation Manual 73 72
Valve Parts List Key No. 50 Part No. 7338111 51 7281291 53 7284964 52 54 7337474 7030713 – 7331185 55 á 57 á 56 58 59 á á á – 7129716 61 á 60 62 63 64 65 66 67 á á á á á 7082087 7199232 – 7342665 68 á 70 7337563 71 7342673 69 á Description Screw, #6-19 x 1-3/8” (2 req.) Motor Motor Mount Cam & Gear Switch Drain Hose Adaptor Kit (includes Key Nos. 55-59) Clip, Drain Drain Hose Adaptor Hose Clamp O-Ring, 5/8” x 13/16” Flow Plug, 2.0 gpm Seal Kit (includes Key Nos.
