User's Manual

5 6 74
receiver
connect button
receiver
connect button
1. Package Contents:
a. Keyboard. b. Mouse. c. Receiver Box.
d. Software. e. Batteries.
2. Install the Batteries:
a. Mouse. b. Receiver. c. Keyboard
3. Notice
1 2 3
QUICK GUIDE
Keyboard & Mouse RF Combo
c.
b.
AAx2
d.c.
a.
e.
AAx2
AAx2
b.
4. Installation:
a. Turn off the computer. Connect
the receiver cable to the PC
via PS/2 ports.
b. Place receiver away from
electronic devices.
8 in (20 cm)
keyboard PS/2 (purple)
mouse PS/2 (green)
8 in (20 cm)
System Requirements
To use the mouse software and the hot keys on your multimedia keyboard,
you need the following:
· Windows XP/ME/2000/98SE/NT 4.0 or later
· PS/2 mouse and keyboard ports
· Sound Blaster compatible sound card (for CD/VCD/DVD, and MPEG operation)
· CD-ROM drive (for software installation and CD/VCD operation)
a.
unlock
AAx2
PS/2 keyboard
connector (purple)
PS/2 mouse
connector (green)
Mouse/Keyboard
connect button
1. Place the RF receiver in a good location.
2. Place the keyboard and the mouse in the
proper location for your computer.
Place the receiver
at least 8 inches(20cm)
from electrical devices
such as the computer or monitor.
Note! Repeat this Step when connecting the Wireless RF
Keyboard & Mouse for the first time and after replacing
the batteries.
5. ID Select 6. Installing Device Drivers
7. Troubleshooting
Connect switches
Connect
switches
Wireless RF Keyboard & Mouse not detected
If the keyboard and mouse don't respond to activity,
follow these steps:
1. Ensure that the receiver cable is properly connected to the
PS/2 mouse and keyboard ports . Ensure that the purple
connector is connected to the keyboard port, and the green
connector is connected to the mouse port.
2. Ensure that the batteries have been installed correctly .
3. Ensure that there are no IRQ or I/O address conflicts.
Refer to your op-erating system user's manual for
information on resolving IRQ and I/O address conflicts.
(A)
(B)
Important
Important
(A) ID connect for keyboard
Press ID select switch on Receiver and then Keyboard
within 10second.
(B) ID connect for mouse
Press ID select switch on Receiver and then Mouse
within 10second.
Shortcut keys
Scroller
Left-click button
Connect button
Right-click button
1.After you have installed and connected Desktop Wireless,
insert the Installation CD into the CD-ROM drive.
The CD supports Windows Autoplay and starts running
automatically. If not, access the CD from Windows Explorer,
and then click the relevant CD-ROM drive. Double click the
Setup.exe file.
2.Select the driver and applications that you want to install,
and then click the OK button.
3.Follow the onscreen instructions to complete the installation.
ID
ID
ID
ID
ID
ID
I
D
I
D
ID
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:
(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,
INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
Federal Communications Commission Requirements
The equipment has been tested and found to comply with the
limits for Class B Digital Device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instruction, may cause harmful interference to radio
communication. However, there is no guarantee that interference
will not occur in a particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
● Reorient of relocate the receiving antenna.
● Increase the separation between the equipment and receiver.
● Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
● Consult the dealer or an experienced radio/TV technician for help.
The changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to
operate the equipment.