30DSERIES E32D5 (Digital Operation) Installation and Operation Manual 234782-1
MANUFACTURED BY Moffat Limited Christchurch New Zealand INTERNATIONAL CONTACTS AUSTRALIA Moffat Pty Limited E.Mail: Main Office: Service: Spares: Customer Service: vsales@moffat.com.au (tel) (03) 9518 3888 (fax) (03 9518 3833 (tel): 1800 622 216 (tel): 1800 337 963 (tel): 1800 335 315 (fax): 1800 350 281 CANADA Serve Canada Web: E.Mail: Sales: Service: www.servecanada.com info@servecanada.com (tel): 800 551 8795 (Toll Free) (tel): 800 263 1455 (Toll Free) NEW ZEALAND Moffat Limited Web: E.
Contents List E32 Turbofan Convection Oven. Model Numbers Covered in this Manual E32D5 - Turbofan Oven - 5 Tray Convection Oven. Introduction ........................................................................................................... 2 Safety Information Specifications ......................................................................................................... 3 Installation........................................................................................................
Introduction Before using your new oven, please read this instruction manual carefully, pay particular attention to any information labelled ‘WARNING’, ‘CAUTION’, ‘IMPORTANT’ or ‘NOTE’ in this manual. Warning Indicates a hazardous situation which, if not avoided, will result in death or serious injury. Caution Indicates a hazardous situation which, if not avoided, will result in minor or moderate injury. This manual must be kept by the owner for future reference.
Specifications E32D5 208V, 50/60Hz, 5.8 kW Oven Power Ratings Oven Tray Details 220 - 240V, 50/60Hz, 6.5 kW Tray Capacity 5 x US Full Pan Tray Spacing 85 mm / 31/3” Max Water Pressure Water Connection 80 psi / 550 kPa.
Installation Installation Requirements Important: • Installation shall comply with local electrical, health and safety requirements. • It is most important that this oven is installed correctly and that oven operation is correct before use. • If you have any questions regarding the proper installation and / or operation of this oven, please contact your local Turbofan distributor.
Installation Electrical Connection Commissioning Before leaving the new installation; Check the oven functions in accordance with the operating instructions specified in the ‘Operation’ section of this manual. Warning This oven must be earthed / grounded. Each oven should be connected to an adequately protected power supply with an appropriate three wire power cord. An isolation switch must be mounted adjacent to, but not behind the oven and must be readily accessible to the operator.
Installation 11. Remove the inner glass latching studs and fit to opposite side of door using Loctite 243 to secure. Reversing the Oven Door NOTE: This operation should only be carried out by a suitably competent person. 12. Turn the door handle over and fit to the other end of the door where the hinges were removed from. Ensure Flat of handle is to the outside. Remove the Oven Door Inner Glass. 1. Open the oven door and open the door inner glass. 2.
Installation 16. Remove the Blanking Screw and Door Catch from the front of the oven and swap around. Door Catch Blanking Screw 17. Fit the door spacers removed at Item 13 opposite to the lower hinge pivot bolt. Oven Door Re-Fitting Fit the Door. 1. Refit the oven door by locating the bottom of the door onto the bottom hinge plate pivot bolt and spacers. 2. Fit the top of the door into the top hinge plate and secure with the top pivot bolt. Top Door Pivot Bolt. Fit Inner Glass to Door.
Operation Operation Guide Warning Warning Take care when opening the oven door during baking. Let hot air and steam escape before removing or replacing food as the steam produced can cause steam burns. Some parts of this oven will become VERY HOT during use and could cause burns if touched. • Turbofan Ovens have been designed to provide simple operation. • This oven is intended for use in a commercial kitchen and must only be put to the use for which it was intended, i.e. cooking food product.
Operation Using the Oven - Manual Mode 1. To check actual oven temperature during preheat or cooking, press ‘Temperature’ button. Actual temperature will display briefly on ‘Temperature Display’ before the display reverts to the pre-set temperature. TURN ‘ON’. Press ‘On-Off’ button. Temperature Dislay. Temperature Display will show actual temperature. 2. Heating ‘On’ Indicator SET TEMPERATURE. + to increase the temperature. - to decrease the temperature.
Operation Cooking in Program Mode 1. TURN ‘ON’. Press ‘On-Off’ button. Press ‘Programs’ button. Program Mode Indicator Heating ‘On’ Indicator Temperature Dislay. Temperature Display will show program selected. 2. To check actual oven temperature during preheat or cooking, press ‘Temperature’ button. Actual temperature will display briefly on ‘Temperature Display’ before the display reverts to the pre-set temperature. SELECT A PROGRAM. + to scroll forward through programs.
Operation Setting the Oven Programs Oven can be pre-programmed with up to 20 Program’s. When you receive your oven, the controller is not programmed. To set programs, carry out the following for each program required:- 1. ENTER PROGRAMMING MODE. Press ‘Programs’ button to enter ‘Programming’ mode. 2. SELECT PROGRAM REQUIRED. Heating ‘On’ Indicator Rotate ‘Temperature Control’ to program required. Temperature Display will show program selected.
Operation Oven Racks The oven is supplied with four general purpose oven racks. • Self Supporting: When fitted, the oven racks are self supporting and will not drop or angle down when the racks are withdrawn during operation, when loading and unloading products onto racks or when attending to the product being cooked during it’s cook cycle.
Operator Accessible Parameters Setting the Operator Accessible Parameters 1. ENTER THE OPERATOR PARAMETER MODE. Press 'Steam' and 'Start / Stop' buttons together. ‘Temperature’ Display will show ‘PAS’. The ‘Time’ Display will flash. 2. SET PASSWORD. Rotate ‘Timer Control’ to set password; (123) (Operator Password). Press ‘Light On / Off’ button to confirm password. ‘Temperature’ Display will show one of Parameter Codes. ‘Time’ Display will show value of the parameter. 3. SETTING THE PARAMETERS.
Cleaning Cleaning Guidelines b. Lift up and unhook the rear of the rack from the locating peg at the rear of the oven. Caution Always turn off electrical power at the mains supply before commencing cleaning. This oven is not water proof. Do not use water jet spray to clean interior or exterior of the appliance. To achieve the best results, cleaning must be regular and thorough. If any small faults occur, have them looked at promptly. Don't wait until they cause a complete breakdown.
Cleaning Side Racks Re-Fitting Right Rack Lamp Glass a. Remove the LH side rack as shown previously. a. Align the bottom of the rack with the 2 brackets in the bottom RH side of the oven. b. Unscrew (anti-clockwise) and remove the lamp glass from the oven. L/Hand Front Locating Peg RH Lower Mounting Brackets b. Tilt the rack upwards and hook the top rear of the rack onto the locating peg in the top rear of the oven. Unscrew Anti-Clockwise R/Hand Rear Locating Peg c.
Cleaning Door Seal a. To remove the door seal, pull the 1 piece seal forward until it pulls out of the location groove around the oven. Note the way the seal is fitted to the oven, with the lip facing inwards. Door Glass Cleaning • Ensure that the oven door is cool before cleaning the oven door glass. a. Open the oven door. b. Lift up the bottom of the inner glass at the centre of the door to unlock from the inner glass retaining catches and swing the glass inwards towards the oven. b.
Fault Finding You may encounter a problem not covered in this section, please contact your service provider who will require the following information:- This section provides a reference to the more common problems that may occur during the operation of your oven. This fault finding guide is intended to help you correct and accurately diagnose problems with your oven.
Electrical Schematics Electrical Schematic E32D5 Turbofan Oven 18
Replacement Parts List Important: Only genuine authorized replacement parts should be used for the servicing and repair of this oven. The instructions supplied with the parts should be followed when replacing components. For further information and servicing instructions, contact your nearest authorized service provider or Turbofan Dealer. When ordering replacement parts, please quote the part number and the description as listed below.
