Technical Specifications

111
Hangers
© 2015 MiTek. All rights reserved.
Face Mount Hanger Charts
Floor
Uplift
1
Joist Size Ref. No. W H D A Qty Nail Qty Nail 100% 115% 125% 160%
JUS26-2 LUS26-2 18 3-1/8 5-1/4 2 1 4 16d 4 16d 1040 1185 1220 1355
JUS28-2 LUS28-2 18 3-1/8 7-1/8 2 1 6 16d 4 16d 1325 1510 1645 1355
10 10d 4 10d 1250 1405 1515 755
10 16d 4 10d 1470 1670 1800 755
12 10d 4 10d 1500 1685 1815 755
12 16d 4 10d 1765 1915 1915 755
HUS26-2 HUS26-2 14 3-1/8 5-1/4 2 1 4 16d 4 16d 1085 1235 1300 1155
HUS26-2IF HUSC26-2 14 3-1/8 5-1/4 2 1 4 16d 4 16d 1085 1235 1300 1155
HUS28-2 HUS28-2 14 3-1/8 7-1/8 2 1 6 16d 6 16d 1625 1850 1995 1810
HUS28-2IF HUSC28-2 14 3-1/8 7-1/8 2 1 6 16d 6 16d 1625 1850 1995 1810
HD26-2 HU26-2 14 3-1/8 5-1/8 2-1/2 1-1/8 12 16d 6 10d 1690 1945 2095 1140
HD26-2IF HUC26-2 14 3-1/8 5-1/8 2-1/2 1-1/8 12 16d 6 10d 1690 1945 2095 1140
HD28-2 HU28-2 14 3-1/8 7-1/8 2-1/2 1-1/8 14 16d 6 10d 1975 2270 2470 1140
HD28-2IF HUC28-2 14 3-1/8 7-1/8 2-1/2 1-1/8 14 16d 6 10d 1975 2270 2470 1140
JUS28-2 LUS28-2 18 3-1/8 7-1/8 2 1 6 16d 4 16d 1325 1510 1645 1355
JUS210-2 LUS210-2 18 3-1/8 9-1/8 2 1 8 16d 6 16d 1845 2105 2290 1980
12 10d 4 10d 1500 1685 1815 755
12 16d 4 10d 1765 1915 1915 755
16 10d 6 10d 2000 2245 2420 1135
16 16d 6 10d 2350 2670 2880 1135
HUS28-2 HUS28-2 14 3-1/8 7-1/8 2 1 6 16d 6 16d 1625 1850 1995 1810
HUS28-2IF HUSC28-2 14 3-1/8 7-1/8 2 1 6 16d 6 16d 1625 1850 1995 1810
HD28-2 HU28-2 14 3-1/8 7-1/8 2-1/2 1-1/8 14 16d 6 10d 1975 2270 2470 1140
HD28-2IF HUC28-2 14 3-1/8 7-1/8 2-1/2 1-1/8 14 16d 6 10d 1975 2270 2470 1140
HUS210-2 HUS210-2 14 3-1/8 9-1/8 2 1 8 16d 8 16d 2170 2465 2660 2210
HUS210-2IF HUSC210-2 14 3-1/8 9-1/8 2 1 8 16d 8 16d 2170 2465 2660 2210
HD210-2 HU210-2 14 3-1/8 9 2-1/2 1-1/8 18 16d 10 10d 2540 2920 3175 1905
HD210-2IF HUC210-2 14 3-1/8 9 2-1/2 -- -- 18 16d 10 10d 2540 2920 3175 1905
HDQ210-2IF HUCQ210-2 14 3-1/4 9 3 1-1/2 12 WS3 6 WS3 5015 5590 5590 2975 31, R1, F32
JUS210-2 LUS210-2 18 3-1/8 9-1/8 2 1 8 16d 6 16d 1845 2105 2290 1980
16 10d 6 10d 2000 2245 2420 1135
16 16d 6 10d 2350 2670 2880 1135
HUS210-2 HUS210-2 14 3-1/8 9-1/8 2 1 8 16d 8 16d 2170 2465 2660 2210
HUS210-2IF HUSC210-2 14 3-1/8 9-1/8 2 1 8 16d 8 16d 2170 2465 2660 2210
HD210-2 HU210-2 14 3-1/8 9 2-1/2 1-1/8 18 16d 10 10d 2540 2920 3175 1905
HD210-2IF HUC210-2 14 3-1/8 9 2-1/2 -- -- 18 16d 10 10d 2540 2920 3175 1905
HUS212-2 HUS212-2 14 3-1/8 11-1/8 2 1 10 16d 10 16d 2710 3080 3325 3060
HUS212-2IF HUSC212-2 14 3-1/8 11-1/8 2 -- -- 10 16d 10 16d 2710 3080 3325 3060
HD212-2 HU212-2 14 3-1/8 11 2-1/2 1-1/8 22 16d 10 10d 3100 3565 3880 1905
HD212-2IF HUC212-2 14 3-1/8 11 2-1/2 -- -- 22 16d 10 10d 3100 3565 3880 1905
HDQ210-2IF HUCQ210-2 14 3-1/4 9 3 1-1/2 12 WS3 6 WS3 5015 5590 5590 2975 31, R1, F32
JUS210-2 LUS210-2 18 3-1/8 9-1/8 2 1 8 16d 6 16d 1845 2105 2290 1980
JUS214-2 LUS214-2 18 3-1/8 13-1/8 2 1 12 16d 6 16d 2420 2755 2995 1980
16 10d 6 10d 2000 2245 2420 1135
16 16d 6 10d 2350 2670 2880 1135
HD210-2 HU210-2 14 3-1/8 9 2-1/2 1-1/8 18 16d 10 10d 2540 2920 3175 1905
HD210-2IF HUC210-2 14 3-1/8 9 2-1/2 -- -- 18 16d 10 10d 2540 2920 3175 1905
HUS210-2 HUS210-2 14 3-1/8 9-1/8 2 1 8 16d 8 16d 2170 2465 2660 2210
HUS210-2IF HUSC210-2 14 3-1/8 9-1/8 2 1 8 16d 8 16d 2170 2465 2660 2210
HUS212-2 HUS212-2 14 3-1/8 11-1/8 2 1 10 16d 10 16d 2710 3080 3325 3060
HUS212-2IF HUSC212-2 14 3-1/8 11-1/8 2 1 10 16d 10 16d 2710 3080 3325 3060
HD212-2 HU212-2 14 3-1/8 11 2-1/2 1-1/8 22 16d 10 10d 3100 3565 3880 1905
HD212-2IF HUC212-2 14 3-1/8 11 2-1/2 -- -- 22 16d 10 10d 3100 3565 3880 1905
HD214-2 HU214-2 14 3-1/8 13 2-1/2 1-1/8 24 16d 10 10d 3385 3890 4230 1905
HDQ210-2IF HUCQ210-2 14 3-1/4 9 3 1-1/2 12 WS3 6 WS3 5015 5590 5590 2975 31, R1, F32
1
)
U
p
lift loads have been increased 60% for wind or seismic loads; no further increase shall be
p
ermitted.
2
)
Minimum nail embedment shall be 1-1/2" for 10d nails and 1-5/8" for 16d nails.
3
)
16d sinkers
(
0.148 dia. x 3-1/4" lon
g)
ma
y
be used at 0.84 of the table load where 16d commons are s
p
ecified. This does not a
pp
l
y
to JUS, HUS, MUS slant nail han
g
ers.
4
)
For JUS and HUS han
g
ers: Nails must be driven at a 30° to 45˚ an
g
le throu
g
h the
j
oist or truss into the header to achieve the table loads.
5
)
WS3 Wood Screws are 1/4" x 3" lon
g
and are included with HDQ han
g
ers.
6
)
NAILS: 10d nails are 0.148" dia. x 3" lon
g,
16d are 0.162" dia. x 3-1/2" lon
g
.
New
p
roducts or u
p
dated
p
roduct information are desi
g
nated in blue font.
5,
R5,
F2
5,
R5,
F2
(2) 2 x 14
SUH210-2 U210-2 1-1/816 3-1/8 8-9/16 2
5,
R5,
F2
1-1/8
1-1/8
3-1/8 5-1/16 2
1-1/8
3-1/8 26-1/4
1-1/8
3-1/8 8-9/16 2
16
16
16
16
(2) 2 x 10
SUH28-2 -- --
SUH210-2 U210-2
(2) 2 x 8
SUH26-2 U26-2
SUH28-2 -- --
(2) 2 x 12
SUH210-2 U210-2
Fastener Schedule
2,3,5,6
Header Joist
USP
Stock No.
Steel
Gauge
3-1/8 6-1/4 1-1/82
3-1/8 8-9/16 2
16
Roof
Code
Ref.
Corrosion Finish
Dimensions (in)
DF/SP
Allowable Loads (Lbs.)
4
Corrosion Finish
Stainless Steel Gold Coat
HDG Triple Zinc
Corrosion Finish Stainless Steel Gold Coat HDG Triple Zinc
Corrosion
Finish
Stainless Steel
Gold Coat
HDG
Triple Zinc
Continued on next page
Hangers
A
D
H
W