尺寸：���mm*���mm 骑马钉 封面���g铜版纸，内页��g书纸
www.miroco.net E-MAIL support@mirocohome.com MANUFACTURER Manufacturer: Shenzhen NearbyExpress Technology Development Co.,Ltd. Address: Floor 7, Building E, Galaxy World Phase II, Shenzhen, China USER GUIDE Miroco Milk Frother Model: MI-MF005 CM Intertek 5016950 MADE IN CHINA Rev_1.
CONTENTS IMPORTANT SAFETY INSTRUCTIONS 01 Package Contents 06 Product Diagram 07 Specifications 08 Preparation Guide 09 Before First Use 10 Using Your Milk Frother 11 Hints & Tips 21 Cleaning and Maintenance 22 Troubleshooting 24 Warranty and Service 27
IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL SAFETY INFORMATION AND INSTRUCTIONS. KEEP FOR FUTURE REFERENCE. Thanks for choosing Miroco Milk Frother. Please read this User Guide thoroughly before use and retain it for future reference.
·Do not place on or near a hot gas or electric burner, or in a heated oven. ·This appliance must be provided with correct voltage via a professionally installed power socket. ·Do not operate the appliance with a damaged cord or plug or after malfunctions occur, or has been damaged in any manner. Return the appliance to the nearest authorized service facility for examination, repair or adjustment.
CAUTION ·Never fill milk higher than the max level or lower than the minimum level marked on the inner wall to avoid overflow. ·Do not operate the appliance when there is no milk inside it. ·Always ensure the whisk is securely attached to the milk jug before use. ·Do not touch the frothing whisk when the unit is working. ·Do not touch hot surfaces. Use handles or knobs.
Package Contents • 1 x Miroco Milk Frother (MI-MF005) • 1 x Frothing Whisk • 1 x Frothing Whisk Holder • 1 x Chocolate Cover • 1 x User Guide Product Diagram ① ⑥ ② ③ ④ ⑤ ⑧ ① Transparent Lid ② Stainless Steel Milk Jug ③ Power Base ④ Function Panel ⑤ Power Button 06 ⑦ ⑨ ⑩ ⑪ ⑥ Chocolate Cover ⑦ Frothing Whisk ⑧ Frothing Whisk Holder ⑨ MAX Level for Heating ⑩ MAX Level for Frothing ⑪ MIN Level for Frothing 03
Specifications Preparation Guide Model MI-MF005 Input 120V~ 60Hz Power 550W Maximum Temperature 65°C - 85 °C /149°F - 185°F Maximum Capacity for Frothing 250ml / 8.5oz Maximum Capacity for Heating 500ml / 16.9oz 08 As a general guide, the chart below shows the whisk function, capacity, operating time and temperature for your reference. Whisk Icon Function Capacity Time Temperature Stirring & Heating (a small amount of milk foam) 500ml / 16.
Note: • The operating time varies with the environment, milk type and initial temperature of the frother. • The above operating time is counted based on heating the milk of 10°C under ambient temperature of 25°C. Before First Use • Remove and safely discard all promotional labels and packing materials attached to the milk frother. • Before first use, wash the milk jug, frothing whisk and lid in warm water with a little detergent then rinse and dry thoroughly.
Stirring & Heating 3 1 12 2 4 1. Place the frothing whisk (without chocolate cover) inside the milk jug. 2. Pour milk into the jug. Do not exceed the MAX Level for Heating (500ml). 3. Press the Power Button within 2 seconds to select the Stirring & Heating mode. 4. The will light up red to start stirring & heating. Once completed, the will keep flashing red for 30 seconds and turn off.
Frothing & Heating 3 1 14 2 4 1. Place the frothing whisk (without chocolate cover) inside the milk jug. 2. Pour milk into the jug. Do not exceed the MAX Level for Frothing (250ml). 3. Press the Power Button within 2 seconds to select the Frothing & Heating mode. 4. The will light up red to start frothing & heating. Once completed, the will keep flashing red for 30 seconds and turn off.
Frothing & Heating Chocolate Milk 500ml 1 16 60g 2 3 4 1. Place the frothing whisk (with chocolate cover) inside the milk jug. 2. Pour milk (500ml) and chocolate powder (60g) into the jug. For better mixing of milk and chocolate, please do not remove the frothing whisk when adding the ingredients. 3. Press the Power Button within 2 seconds to select the Frothing & Heating Chocolate Milk mode. 4. The will light up red to start frothing & heating chocolate milk.
Frothing Cold Milk 3 1 18 4 2 15
Milk Frother Sounds Hints & Tips 1. During the operation, the milk frother will alert you with beep sounds. ·Beep once when i. plugged in, ii. starts working under selected mode, or iii. milk jug is removed from the power base. ·Beep 3 times when the selected mode is completed. 2. To mute the sounds, press and hold the Power Button for 3 seconds. ·We recommend the use of a long life milk (UHT) with a high protein content.
before frothing milk. MAX Fill Line (500ml / 16.9oz) before heating milk. ·Pour frothed milk promptly to avoid the milk from separating. ·Clean the milk jug immediately after each use. Flush and clean the walls using warm, soapy water and a non-abrasive cloth. Then dry with a soft cloth. The milk jug and lid can be washed in the dishwasher. water. Once the milk jug and frothing whisk have cooled completely, remove the frothing whisk and rinse off any milk in warm water.
Troubleshooting Problem Milk is not foaming? Milk is not heating 24 Possible Causes Solution Milk is warm or too hot to foam. • Use cold, fresh (or freshly opened) milk. • Do not re-foam already heated milk. • Try reducing the quantity of milk in the milk jug. • Try a different milk. Experiment with different milk and frothing whisks to achieve the desired result. / • Ensure the milk jug is correctly positioned onto the power base. • Ensure that the milk frother has been properly turned on.
Problem Possible Causes Grinding noise • Frothing whisk is not placed correctly. • Take out the frothing whisk during working. • The milk jug has been removed from the power base during operation. 26 Solution Warranty and Service This product is covered with Miroco product and labor warranty for 12 months from the date of its original purchase. If any problems occur, please contact the Miroco Customer Care Centre in your country via the contact information listed in this User Guide.
FCC Compliance This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
