Assembly Instructions

ManualsBrandsMGA Entertainment ManualsDronesMy First Helicopter

CONTENTS

AGES 3+ YEARS

Illustrations are for reference only. Styles may vary from actual contents.

CAUTION: KEEP FINGERS AWAY

FROM SPINNING PROPELLERS

QUICK START

NOTE: Please read all instructions before use and keep this manual for future reference.

Before beginning, an adult must install fresh alkaline batteries. Here’s how:

1. Using a Phillips screwdriver (not included), remove the screw and battery compartment cover

located on the back of the remote.

2. Install six (6) fresh 1.5V AA (LR6) alkaline batteries (not included) making sure the (+) and (-)

ends face the proper direction as indicated inside the battery compartment.

3. Replace the compartment cover and tighten the screw.

BATTERY INSTALLATION

CHARGING THE HELICOPTER

6 x AA Batteries

1.5V AA/LR6

POWER INDICATOR

POWER SWITCH

RIGHT TURN

LANDING

CHARGING PLUG

EMERGENCY

STOP

TAKE OFF

LEFT TURN

Take out the charging cable from the

bottom of the remote.

Turn the helicopter OFF (O/ ) and insert the cable

into the charging station under the helicopter.

I = ON

O = OFF

Turn ON (I / ) the remote control. The light on the

remote control will turn red and blink. Once it has

nished charging, the light on the remote will turn

green. Unplug the charging cable and replace the

cord in the unit.

Turn the helicopter ON (I). The power LEDs on the headlights will ash.

Place the helicopter on a at surface and stand three feet away.

Turn the remote control ON (I/ ). The power indicator will light up.

3 FEET

EMERGENCY STOP:

If the helicopter crashes, press the stop button to

stop the propellers. Turn the helicopter and

remote control o. Examine the helicopter for any

damage before switching it on and ying again.

I /

HELICOPTER AND REMOTE CONTROL PARTS

PROTECTIVE RINGS

STABILIZER

STABILIZER LINKAGE

ROTOR BLADES

CHARGING

SOCKET

POWER

SWITCH

SKID

SENSOR

FLYING LESSONS

• If the helicopter crashes, switch the remote control and the helicopter to the OFF positions. Carefully check

that no damage was done to the helicopter in the crash before turning the unit on again.

• For best results, use the helicopter away from bright lights.

• Do not cover the sensor on the helicopter.

• Keep the remote control within 15 feet (5 meters) of the helicopter to avoid loss of reception.

HELPFUL FLYING TIPS

Replacement Parts

A. 1 Helicopter

B. 1 Remote Control

C. Top Rotor Blade

D. Bottom Rotor Blade

E. 2 Wings

F. Connector

G. Screwdriver

H. 5 Screws (One screw will be attached

to the stem of the top rotor blade.)

I. 2 Screws for the Wings

ADULT SUPERVISION, ASSEMBLY,

AND BATTERY INSTALLATION REQUIRED

1) Install 6 “AA” (LR6) batteries in the remote control.

2) Charge the helicopter’s battery for 30-40 minutes.

3) Turn on the helicopter.

4) Turn on the remote control.

5) Use the buttons on the remote control to y your helicopter in an open, indoor area.

H. x4

I. x2

SKU: 655517E5C

ENG

Summary of content (2 pages)

PAGE 1
FLYING LESSONS AGES 3+ YEARS HELPFUL FLYING TIPS BATTERY INSTALLATION ENG ADULT SUPERVISION, ASSEMBLY, AND BATTERY INSTALLATION REQUIRED SKU: 655517E5C CONTENTS Before beginning, an adult must install fresh alkaline batteries. Here’s how: 1. Using a Phillips screwdriver (not included), remove the screw and battery compartment cover located on the back of the remote. 2. Install six (6) fresh 1.
PAGE 2
EMERGENCY STOP: If the helicopter crashes, press the stop button to stop the propellers. Turn the helicopter and remote control off. Examine the helicopter for any damage before switching it on and flying again. 4 PRESS LIMITED WARRANTY TROUBLESHOOTING The helicopter does not respond: • Check that the helicopter and remote control are both turned to the “ON” position. • The batteries in the remote control may need replacing or the helicopter may need to be recharged. • The helicopter may have crashed.