802 Stirrer Manual 8.802.
Metrohm AG CH-9101 Herisau Switzerland Phone +41 71 353 85 85 Fax +41 71 353 89 01 info@metrohm.com www.metrohm.com 802 Stirrer Manual 8.802.8001EN 06.
Teachware Metrohm AG CH-9101 Herisau teachware@metrohm.com This documentation is protected by copyright. All rights reserved. Although all the information given in this documentation has been checked with great care, errors cannot be entirely excluded. Should you notice any mistakes please send us your comments using the address given above. Documentation in additional languages can be found on http://products.metrohm.com under Literature/Technical documentation.
￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭ Table of contents Table of contents 1 Introduction 1.1 1 Instrument description ......................................................... 1 1.2 About the documentation ................................................... 1 1.2.1 Symbols and conventions ........................................................ 1 1.3 Safety instructions ................................................................ 2 1.3.1 General notes on safety ....................................................
￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭ Table of contents 6 Accessories 17 6.1 Scope of delivery ................................................................ 17 6.1.1 802 Stirrer for 727 Ti Stand 2.802.0010 ................................ 17 6.1.2 802 Stirrer (USA) 2.802.0011 ................................................. 17 6.1.3 802 Stirrer (EU) 2.802.0014 ................................................... 18 6.1.4 802 Stirrer for sample changer 2.802.0020 ............................ 19 6.1.
￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭ Table of figures Table of figures Figure 1 Figure 2 802 Stirrer ......................................................................................... 5 802 Stirrer with its own control .........................................................
￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭ 1 Introduction 1 Introduction 1.1 Instrument description The propeller rod stirrer 802 Stirrer is controlled by a Touch Control or a PC software. It however has its own control. The stirring rate is set by a controller. The 802 Stirrer can be connected to a titration stand, a tower of a sample changer or directly to a sample changer. 1.2 About the documentation CAUTION Please read through this documentation carefully before putting the instrument into operation.
￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭ 1.3 Safety instructions Warning This symbol draws attention to a possible biological hazard. Caution This symbol draws attention to a possible damage of instruments or instrument parts. Note This symbol marks additional information and tips. 1.3 Safety instructions 1.3.1 General notes on safety WARNING This instrument may only be operated in accordance with the specifications in this documentation.
￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭ 1 Introduction Mains voltage WARNING An incorrect mains voltage can damage the instrument. Only operate this instrument with a mains voltage specified for it (see rear panel of the instrument). Protection against electrostatic charges WARNING Electronic components are sensitive to electrostatic charges and can be destroyed by discharges.
￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭ 1.3 Safety instructions 1.3.5 Recycling and disposal This product is covered by European Directive 2002/96/EC, WEEE – Waste from Electrical and Electronic Equipment. The correct disposal of your old equipment will help to prevent negative effects on the environment and public health. More details about the disposal of your old equipment can be obtained from your local authorities, from waste disposal companies or from your local dealer.
￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭ 2 Device overview 2 Device overview 2.1 802 Stirrer 1 2 Figure 1 1 802 Stirrer Connector plug For connecting the propeller stirrer to the stirrer connector of a device or to a controller. 2 Metal rod For fastening a stirring propeller.
￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭ 2.2 802 Stirrer with its own control 2.2 802 Stirrer with its own control 1 4 2 5 3 6 7 8 9 10 Figure 2 802 Stirrer with its own control 1 Drive of the propeller stirrer 2 Electrode holder (6.2021.020) 3 Stirring propeller (6.1909.0104) 4 Support rod (6.2016.070) Length 40 cm 5 Switching contacts The stirrer is switched on by a suitably attached electrode holder. 6 Controller (6.2137.
￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭ 2 Device overview 7 Rotary wheel For setting the stirring rate. If the end of the scale is reached, turn to the other end in order to readjust the scale. 8 Clamping screw For fixing the positioning height of the 6.2137.000 rotary controller on the support rod. 9 Connector plug For connecting the propeller stirrer.
￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭ 3.1 Setting up the instrument 3 Installation 3.1 Setting up the instrument 3.1.1 Packaging The instrument is supplied in highly protective special packaging together with the separately packed accessories. Keep this packaging, as only this ensures safe transportation of the instrument. 3.1.2 Checks Immediately after receipt, check whether the shipment has arrived complete and without damage by comparing it with the delivery note. 3.1.
￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭ 3.2 3 Installation Mounting the 802 Stirrer to the titration stand 1 2 Mounting the propeller stirrer as follows: 1 Insert the propeller stirrer 802 Stirrer without the stirring propeller from above into the center opening of the electrode holder. 2 Plug the stirring propeller from below to the propeller stirrer. 3.
￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭ 3.4 Connecting the 802 Stirrer to the sample changer 3.4 Connecting the 802 Stirrer to the sample changer Connecting the propeller stirrer directly to the sample changer a) Ind. Ref. Temp. Remote Pol. MSB USB Made by Me trohm Switze rland b) Connect the propeller stirrer as follows: 1 Connect the cable of the 802 Stirrer to the stirrer connector (with stirrer symbol) on the rear of the tower (a) or directly to the sample changer (b).
￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭ 3 Installation Connecting the propeller stirrer with the titration stand to the sample changer USB 1 MSB 3.804.30 Contr. MSB 2 MSB 3 0X Connect the propeller stirrer with the titration stand as follows: 1 Exit the control software. 2 Connect the connection cable of the titration stand to one of the sockets marked with MSB on the rear of the control device. 3 Connect the propeller stirrer to the stirrer socket (with stirrer symbol) of the titration stand.
￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭ 4.1 Rotational speed 4 Technical specifications 4.1 Rotational speed Maximum rotational speed ±2050...2250 U/min Setting of the rotational speed ±15 steps Increase of rotational speed per step ±140...150 U/min 4.2 Power supply Voltage +12 V, -12 V, +5 V Power consumption 4W Fuse Electronic overload protection 4.3 Safety specifications Design and testing ￭ ￭ ￭ ￭ ￭ 4.4 EN/IEC 61010-1:2001 UL 61010-1: 2004 CSA-C22.2 No.
￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭ 4 Technical specifications ￭ ￭ ￭ ￭ 4.5 EN/IEC 61000-4-6: 2001 EN/IEC 61000-4-11: 2004 EN/IEC 61000-4-14: 2004 NAMUR:2004 Ambient temperature Nominal function range +5…+45 °C (at a maximum of 85% humidity) Storage –20…+60 °C Transport –40…+60 °C 4.
￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭ 5.1 Declaration of Conformity 5 Conformity and warranty 5.1 Declaration of Conformity This is to certify the conformity to the standard specifications for electrical appliances and accessories, as well as to the standard specifications for security and to system validation issued by the manufacturing company. Name of commodity 802 Stirrer Rod stirrer for the connection to Metrohm instruments.
￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭ 5 Conformity and warranty Metrohm Ltd. is holder of the SQS certificate ISO 9001:2000 Quality management system for development, production and sales of instruments and accessories for ion analysis. Herisau, 6 January, 2009 5.2 D. Strohm A. Dellenbach Vice President, Head of R&D Head of Quality Management Quality Management Principles Metrohm Ltd.
￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭ 5.3 Warranty (guarantee) Manufacture The measures put into practice in the production of our instruments guarantee a constant quality standard. Production planning and manufacturing procedures, maintenance of production means and testing of components, intermediate and finished products are prescribed. Customer support and service Customer support involves all phases of instrument acquisition and use by the customer, i.e.
￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭ 6 Accessories 6 Accessories 6.1 Scope of delivery NOTE Subject to change without notice. 6.1.1 Qty. 1 802 Stirrer for 727 Ti Stand 2.802.0010 Order no. Description 1.802.0010 802 Stirrer Propeller stirrer 1 6.1909.010 Stirring propeller / 96 mm Stirring propeller, fitting length from lower edge of the ground joint: 96 mm. For usage in beakers with 702, 802 propeller stirrer. Material: PP 1 6.2137.000 Controller for 722/727 For 722 Rod Stirrer or 727 Ti Stand 1 6.
￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭ 6.1 Scope of delivery Qty. Order no. Description Propeller stirrer 1 6.1909.010 Stirring propeller / 96 mm Stirring propeller, fitting length from lower edge of the ground joint: 96 mm. For usage in beakers with 702, 802 propeller stirrer. Material: PP 1 6.1910.000 Switching ring For the 6.2137.000 controller for the 722, 803 or 727 Ti Stand, if used with another electrode holder than the 6.2021.030. 1 6.2119.020 Power supply USA 110V/9V DC With US mains plug.
￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭ Qty. 1 6 Accessories Order no. Description 6.1909.010 Stirring propeller / 96 mm Stirring propeller, fitting length from lower edge of the ground joint: 96 mm. For usage in beakers with 702, 802 propeller stirrer. Material: PP 1 6.1910.000 Switching ring For the 6.2137.000 controllor for the 722, 803 or 727 Ti Stand, if used with another electrode holder than the 6.2021.030. 1 6.2117.020 Power supply EU 220V/9V DC With Euro mains plug. Input: 220...240 V AC.
￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭ 6.1 Scope of delivery Qty. 1 Order no. Description 6.1909.020 Stirring propeller / 104 mm Stirring propeller, fitting length from lower edge of the ground joint: 104 mm. For usage in beakers with 722, 802 propeller stirrer. Material: PP 1 6.1.5 Qty. 1 8.802.8001DE Manual 802 Stirrer 802 Stirrer for 804 Ti Stand 2.802.0040 Order no. Description 1.802.0010 802 Stirrer Propeller stirrer 1 6.1909.
￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭ 6 Accessories 6.2 Optional accessories 6.2.1 802 Stirrer 2.802.0010, 2.802.0011, 2.802.0014, 2.802.0020 und 2.802.0040 Order no. Description 6.1909.050 Stirring propeller for 120 mL beakers Stirring propeller for the usage of the 802 Stirrer with a sample rack for 120 mL beakers (6.1459.300). Material: ETFE Length (mm): 111 6.1909.
