Datasheet
MAX9176/MAX9177
670MHz LVDS-to-LVDS and
Anything-to-LVDS 2:1 Multiplexers
10 ______________________________________________________________________________________
CHARGE-CURRENT
LIMIT RESISTOR
DISCHARGE
RESISTANCE
STORAGE
CAPACITOR
C
s
100pF
R
C
1MΩ
R
D
1.5kΩ
HIGH-
VOLTAGE
DC
SOURCE
DEVICE
UNDER
TEST
Figure 9. Human Body Test Model
CHARGE-CURRENT
LIMIT RESISTOR
DISCHARGE
RESISTANCE
STORAGE
CAPACITOR
C
s
150pF
R
C
50Ω TO 100Ω
R
D
330Ω
HIGH-
VOLTAGE
DC
SOURCE
DEVICE
UNDER
TEST
Figure 10. IEC 61000_4-2 Contact Discharge Test Model
Applications Information
Power-Supply Bypassing
Bypass the V
CC
pin with high-frequency surface-mount
ceramic 0.1µF and 0.001µF capacitors in parallel as
close to the device as possible, with the smaller valued
capacitor closest to V
CC
.
Differential Traces
Input and output trace characteristics affect the perfor-
mance of the MAX9176/MAX9177. Use controlled-
impedance differential traces (100Ω typical). To reduce
radiated noise and ensure that noise couples as com-
mon mode, route the differential input and output sig-
nals within a pair close together. Reduce skew by
matching the electrical length of the two signal paths
that make up the differential pair. Excessive skew can
result in a degradation of magnetic field cancellation.
Maintain a constant distance between the differential
traces to avoid discontinuities in differential impedance.
Minimize the number of vias to further prevent imped-
ance discontinuities.
Cables and Connectors
Interconnect for LVDS typically has a controlled differ-
ential impedance of 100Ω. Use cables and connectors
that have matched differential impedance to minimize
impedance discontinuities.
Avoid the use of unbalanced cables such as ribbon or
simple coaxial cable. Balanced cables such as twisted
pair offer superior signal quality and tend to generate
less EMI due to magnetic field canceling effects.
Balanced cables pick up noise as common mode,
which is rejected by the LVDS receiver.
Termination
The MAX9176/MAX9177 require external input and out-
put termination resistors. For LVDS, connect an input
termination resistor across each differential input and at
the far end of the interconnect driven by the LVDS out-
put. Place the input termination resistor as close to the
receiver input as possible. Termination resistors should
match the differential impedance of the transmission
line. Use 1% surface-mount resistors.
The MAX9176/MAX9177 feature an integrated differen-
tial output resistor. This resistor reduces jitter by damp-
ing reflections produced by any mismatch between the
transmission line and termination resistor at the far end
of the interconnect.
Board Layout
Separate the differential and single-ended signals to
reduce crosstalk. A four-layer printed circuit board with
separate layers for power, ground, differential signals,
and single-ended logic signals is recommended.
Separate the differential signals from the logic signals
with power and ground planes for best results.
IEC 61000-4-2 Level 4 ESD Protection
The IEC 61000-4-2 standard (Figure 10) specifies ESD
tolerance for electronic systems. The IEC61000-4-2
model specifies a 150pF capacitor that is discharged
into the device through a 330Ω resistor. The MAX9176/
MAX9177 differential inputs and outputs are rated for
IEC61000-4-2 level 4 (±8kV Contact Discharge and
±15kV Air-Gap Discharge). The Human Body Model
(HBM, Figure 9) specifies a 100pF capacitor that is dis-
charged into the device through a 1.5kΩ resistor.
IEC 61000-4-2 level 4 discharges higher peak current
and more energy than the HBM due to the lower series
resistance and larger capacitor.