Color Video Camera Instruction Manual Models: LD300N-B/C/D/E/F LD300P-B/C/D/E/F Before installing, operating or adjusting this product, please read this instruction booklet carefully and completely.
CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
WARNING: Do not install this equipment in a confined space such as a bookcase or similar unit. WARNING: This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. WARNING: Wiring methods shall be in accordance with the National Electric Code, ANSI/NFPA 70. WARNING: To reduce a risk of fire or electric shock, do not expose this product to rain or moisture.
Important Safety Instructions 1. 2. 3. 4. 5. Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9.
Safety Precautions Do not attempt to disassemble the camera Avoid the camera with direct sunlight Do not use strong solvents or detergents Handle the camera with care To prevent electric shock, do not remove screws or covers. There are no user serviceable parts inside. Ask a qualified service personnel for servicing. Use a dry cloth to the camera when it is dirty. If it is hard to remove the dirt on the camera, use a mild detergent and wipe it gently.
What's in the box Video Cable Power Cable Camera Body M4 Tapping Screws (2EA) (Pan Lock Screw) Optional Adapter (DC 12V, 300mA)
Construction Front View 6-pin Dip Switch Tilt Base Focus Lock Screw Side View Lens Tilting Lock Screw Dome Cover Separatory Spring
Installation Camera Installation 1. Aim the LG logo of the Dome Camera to face the place that you wish to watch. 2. Tighten the M4 Tapping Screws to fix the Dome Camera on the ceiling, then adjust the Pan (Left /Right) by moving the Pan Base. Tighten the M4 Tapping Screws after adjustment. 3. Loosen the Tilting Lock Screw. Adjust the Tilt(Up /Down) by moving the Tilt Base then tighten Tilting Lock Screw. 4. Loosen the Focus Lock Screw.
Installation Camera Connection Connect the Power Adapter (DC 12V, 300mA; optional) to the Power Input Jack of the camera as shown below.
Installation Notes: • When you disassemble the Dome Cover, lift the Dome Cover Separatory Spring on the opposite side of LG Logo and turn the Dome Cover clockwise simultaneously. Dome Cover Separatory Spring • When you install the camera, handle with care. The camera could be damaged by improper handling or storage. • If this camera is mounted on the other places except ceiling, you need an extra bracket for mounting.
Setup 6-pin Dip Switch Setting This camera has the 6-pin Dip Switch for setting. 2. FL (Flickerless) Use for removing the flicker of picture. The default setting is OFF. 3. AWB/HOLD AWB (Auto White Balance), HOLD (White Balance Hold). The default setting is AWB. 4. BLC Backlight compensation eliminates strong background light which makes the camera picture dark such as a spotlight. You can select the mode for adjusting the iris lens. The default setting is OFF. 5. L/L Not used. 1.
Troubleshooting Check the following guide for the possible cause of a problem before contacting service. The picture is poor Does the Dome Cover have lots of dust on the surface? - Use a dry cloth to clean the camera when it is dirty. Smear may be caused to the screen of night than daytime. - Adjust the Focus by moving the Focus Lens. 12 Contrast of the screen is not clear. Check the condition of the monitor. A light source such as a spot light causes burn-in on the display screen.
Dimension ø100 76.5mm 26.
Specifications Model Signal System Total/Effective Pixels Pick-Up Device Lens Angular Field of View(D) Focus Signal Process Scanning System Sync. System Scanning Frequency Resolution S/N Ratio Standard Illumination Minimun Illumination Video Output Signal Gain Control Shutter speed White Balance Back Light 14 LD300P-B/C/D/E/F LD300N-B/C/D/E/F PAL NTSC 470K/440K 410K/380K 1/3 - inch interline color CCD(Super HAD) Fixed Lens (F=3.0mm (LD300-B), 3.7mm (LD300-C), 6.0mm (LD300-D), 8.
Specifications Model Power Source Power Consumption Operating Temp. Storage Temp. Weight Dimensions LD300P-B/C/D/E/F LD300N-B/C/D/E/F DC 12V Less than 2.3W -10 ºC ~ 50 ºC (Humidity :0%RH ~60%RH) -20 ºC ~ 60 ºC (Humidity :0%RH ~85%RH) 205g 120 (Diameter) x 76.
P/NO: MFL40426658